Question about Cars & Trucks

1 Answer

How to replace the cable on my come along - Cars & Trucks

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Habit-Forming:

    Visited the website for 3 consecutive days.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 57 Answers

Fasten cable around a tree or something to anchore it,reverse until it all comes off the spool and you will see the conecction to remove good luck

Posted on Dec 17, 2016

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

There is no place to attach the cable on my come along


come alongs are attached at one end to a fixture ( tree ,back of a vehicle etc
the cable is thread through the jaws of the comalong and the back and forward action of the lever pulls it in and consequently anything that the other end of the cable is attached to is pulled along ( out of the bog etc)
that is why the cable has one end with a "eye" and the other end is plain and straight so that it goes through the machine

Dec 17, 2016 | Cars & Trucks

1 Answer

How do i replace my hand brake cable on my ford falcon XH ute


wait a bit ....is it rear disc or rear drums on that ute

will assume its under dash hand brake pull lever tyoe

the disc setup may have single cables for each rear
rear disk brake cable is approx $ 150

if your XH it is close to the XE and XF set up drums
a complete one line loop cable outer and inner
with plastic grommets along the back chassis rail ( they break )
so the one inner cable works both rear handbrake shoes


hand brake cable is a shorty

undo the adjustment thread
just below the hand brake cable point up somewhere above the gearbox
(drums )
after new cable fitted
drums are adjusted with the old school way with the handbrake adjuster tool
handbrake cable adjusted

then the handbrake handle when pulled out to hold needs14 plus clicks
comes out a long way for some weird reason
on drums
if cable adjustment is done wrong onrear drums the handbrake cable will come loose in the drum as you drive along

26261095-l1jraapkfcyxqeqgczv0cruv-4-0.jpg

26261095-l1jraapkfcyxqeqgczv0cruv-4-3.jpg

26261095-l1jraapkfcyxqeqgczv0cruv-4-5.jpg

Aug 17, 2016 | Ford Cars & Trucks

1 Answer

How do i replace interior latch for hood


The interior latch is a kit along with the latch. The latch alone cannot be replaced as it comes along with a steel cable.

Aug 22, 2014 | 2010 Mitsubishi Lancer

1 Answer

S40, volvo, keep blowing a turn signal fuse


When a fuse keeps blowing everytime you replace it that means there is a short circuit along its cable. Check the flasher cables or call a car electrician to do it.

May 27, 2014 | 2004 Volvo S40

1 Answer

How to change shifting cable on a 2004 pacifica


just work your way along cable and remove parts as you go remembering how they go back take notes,draw sketch's etc you'll be ok,all so get a workshop manual

Apr 25, 2014 | 2004 Chrysler Pacifica

1 Answer

Positive battery cable replacement


Use a battery wrench usually 8mm to open the terminal bolts. Undo both of them and disconnect both the cables (positive and negative). Disconnect the other end of the positive cable by following it along its length. Undo the bolt that holds it. And now you can replace the cable. Follow the same process in reverse for reinstallation.

Jun 23, 2013 | Toyota Avalon Cars & Trucks

1 Answer

GROUND CABLE CLAMP BROKE AND IS BADLY CORRIDED


its just taped into the harness you should be able to run a new one along side the harness

Jul 11, 2012 | 1999 Jeep Grand Cherokee

2 Answers

Sir, i have a problem with my hyundai accent. I see spark jumping from the ignition coil. And it is affecting my vehicles performance. sometimes it seems to be like the engine is going to stop. when i...


if the coil is arching still after replacing it new then replace the spark plug wires. faulty wires will cause the arching and so will a cracked distributor cap replace it along with the wires and your problem will be solved

Nov 06, 2010 | 2000 Hyundai Accent

1 Answer

How do u replace a shifter cable for a 1988 honda accord lx


remove cable from transmission,follow cable behind engine,along exhaust pipe,then up through floor into center console.along the way you will find retainer clips (on both ends of cable) which hold the cables in place,and also underneath you will find a fastner which holds cable to bottom of floorboards and a panel with a rubber gasket in which the cable goes up into the console through. you must then remove center console to release the other end of cable.Once cable is loose go under car in the middle of the cable and pull out from floor then pull the other end out from engine compartment.

Jul 17, 2008 | 1988 Honda Accord 4 Door

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...