Question about 2003 Kia Rio

Open Question

Will a 2004 Kia Rio engine bolt directly into a 2003 Kia Rio? All wiring harnesses etc fit without modification?

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: My 2003 Kia Rio Cinco back hatch latch handle is

We had the same problem.
I took out the bolts outside, then crawled into the back area of the car, and took a screw driver, and slid it along the inner hatch catch, and found the safety latch and released the hatch. Then I took the inside off, and disconnected the handle device from the inside. It was rusted, and broken. I went to Kia, and bought a new one and reinstalled, after greasing the new one up. Took me a while, but they wanted 280.00 in labor, so it was well worth it.
Just be patient and go slow. A good metric socket set will be the best thing, with a regular and phillips screw driver.
Good luck
David

Posted on Jun 24, 2009

  • 14036 Answers

SOURCE: 2003 Kia Rio check engine light keeps coming on,

you could have a dirty fuel injector or a leaking intake.

Posted on Jul 24, 2009

  • 972 Answers

SOURCE: Check engine light is on for my 2003 Kia Rio. At

my 01 did that and it was the plug wires it bucked real bad
next time it happened it was just sluggish up hills and light would come on. it was the fuel filter it had 255,000 miles on it

Posted on Mar 23, 2010

  • 46 Answers

SOURCE: i need to find the torque specs for the connecting

22 - 24 ft. lbs. for the rod caps and....
110795143Cylinder Head Tightening Torque and Sequence.

Tighten cylinder head bolts in order shown.
Tightening torque: 36.1 ft. lbs. (49 Nm, 5 kg-m)

Loosen bolts in reverse of order shown.

Retighten cylinder head bolts in order shown.
Tightening torque: 18 ft. lbs. (25 Nm, 2.5 kg-m)

Mark cylinder head bolts for rotational reference.
Rotate cylinder head bolts 90°(1/4 Turn) in order shown.

CAUTION:

  • Do not reuse the old cylinder head bolts.

Posted on May 31, 2010

Testimonial: "thank you so much for your help is been a nightmare getting info on this car thanks again"

roniecon
  • 6826 Answers

SOURCE: 2004 Kia Rio turns over but won't start.

These are coil packs,the most likely problem will be the crank sensor,or the cam sensor,these are what trigger the pulse for spark,and injector pulse.

Posted on Jun 07, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the knock sensor located on the engine of 2003 kia rio?


Take off the air cleaner assy and on the back of the engine by the fire wall under the exhaust manifold you will see a wire coming up going to a connector thats the knock sensor one bolt that holds it on the engine and unplug it your done

Apr 30, 2016 | 2003 Kia Rio

2 Answers

Firing order for 2003 kia rio? ? ? 1 2 3 4 ? ? ...


Hi Grey:
1-3-4-2. (2004 Kia Rio Manual, current for A3D and A5D engines.)

Hope this helps; also keep in mind that your feedback is important and I'll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using Fixya, and have a nice day.

Dec 13, 2011 | 2003 Kia Rio

4 Answers

2003 kia rio I changed the fuel filter the car


had similar problem, 2003 rio 1.6l idle fine and die when trying to accelerate or lurch and die ran fine in reverse change timing belt,wires plugs, had codes for multi cyl misfire and low injector voltage, still same lurch and die. try wiggle test on sensor plugs and main engine harness between battery and engine . i did this and found car smoothed out,tried wiggle again and car died,took harness apart where i wiggled it and found broken wire to crank sensor.good now

Apr 11, 2010 | 2003 Kia Rio

1 Answer

Where is the drain/refill plug for gear oil? kia rio 5spd 2002


I have a 2004 Kia Rio and you have to take off the speedometer cable/wiring harness from the top of the trans and fill it from there...the drain plug/bolt is underneath the trans from there...

Apr 06, 2010 | 2004 Kia Rio

1 Answer

Check engine light is on for my 2003 Kia Rio. At


my 01 did that and it was the plug wires it bucked real bad
next time it happened it was just sluggish up hills and light would come on. it was the fuel filter it had 255,000 miles on it

Mar 23, 2010 | 2003 Kia Rio

1 Answer

Knock sensor replacement ....2003 kia rio....emissions ...obd II....failure...need to pass inspection...failure code P0325 (Knock sensor 1 circuit malfunction)....where vis the knock sensor located on a...


Turn ignition off. Disconnect knock sensor 3
-
pin harness connector. Locate knock sensor, on cyli
nder block.
On Optima 2.7L engine, sensors are located on both
sides of cylinder block. . Remove knock
sensor from cylinder block. To install, reverse rem
oval procedure.

Mar 19, 2010 | 2003 Kia Rio

2 Answers

How do I replace the knock sensor on my 2003 kia rio?


On 2003 Kia Rio the knock sensor is located under the intake manifold and must be changed from underneath the car. If you remove the oil filter it is directly above it and is in clear view once the oil filter is out of the way. The connector plugs in behind the intake manifold air breather on the top side. If you remove the air breather cover it will help you get to it. I wish I had someone tell me where it was instead of looking for it for over 2 hours. It is simple after you find it.

Dec 10, 2009 | 2003 Kia Rio

1 Answer

Gear box oil filler plug - kia rio 2004


you have to take off the speedometer cable/wiring harness from the top of the trans and fill it from there....one 10mm bolt...very awkward spot...it might be snug, so just take a flat head screwdriver from underneath to tap it loose...

Dec 26, 2008 | 2002 Kia Rio

1 Answer

Gear box oil filler plug - kia rio


you have to take off the speedometer cable/wiring harness from the top of the trans and fill it from there....one 10mm bolt...very awkward spot...it might be snug, so just take a flat head screwdriver from underneath to tap it loose...

Dec 26, 2008 | 2004 Kia Rio

Not finding what you are looking for?
2003 Kia Rio Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kia Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

75066 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...