Question about Cars & Trucks

1 Answer

Do I need to remove the radiator etc to replace the fan belt on 2l 2009 Actyon ute ?? ta Paul

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 47,675 Answers

Should not be necessary
remove the belt from the pulleys then put the belt over the top of a fan blade , turn the fan and put the belt over the next blade and so until the belt is in front of the fan then pull it out between blades
fitting belt is the reverse procedure

Posted on Dec 17, 2016

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Repacement of belt that drives the second radiater fan on jetta cli 2l 1992. the 1st one is driven electrically.


huh ... jetta cooling fans show up as electric direct driven

number one or five .... 2.... drive belt layout

or diesel last picture

26347671-5c0cei0pi4b5yrcoqdtg5q3m-2-0.jpg

26347671-5c0cei0pi4b5yrcoqdtg5q3m-2-1.jpg

26347671-5c0cei0pi4b5yrcoqdtg5q3m-2-3.gif

Nov 09, 2016 | Cars & Trucks

1 Answer

How to replace the clutch fan on a Isuzu rodeo


no year, engine (size) stated.
on all cars its the same,
gain access to it, (shrouds,etc, depands on how big your arms are.)
off the fan belt. (release tension-er.)
off the fan and clutch replace new clutch to old fan/.
put back
set tension on belt.

the FSM steps for fan off are below (buy the FSM and read it?)
guess 1995...
  1. the fan is first then clutch.
  2. Disconnect the negative battery cable.
  3. Remove the upper radiator shroud and, if desired for additional clearance, remove the radiator from the vehicle.
  4. Although it is not necessary in most cases, the radiator may be removed from the vehicle for easier access to the fan
  5. retainers. If the radiator is left in place, use extra caution to prevent damage to the fragile radiator fins.
  6. Remove the fan assembly attaching nuts (clutch type) or bolts (standard type), then remove the fan assembly from the engine.
  7. Some vehicles use a space between the fan and the water pump pulley. If used, be sure to retain the spacer for
  8. installation.
  9. If necessary, the clutch may be removed from the fan by removing the attaching nuts or bolts (as applicable).
  10. end remove.

Nov 12, 2015 | Isuzu Cars & Trucks

1 Answer

Need to replace the radiator on my 1999 Ford Contour SE. It's a 2L. Some pages say take from top..others, from the bottom. Can't find any videos to help me out


You need to raise and support the vehicle high enough to remove the radiator from the bottom. Drain the coolant. Disconnect the coolant hoses from the radiator. Disconnect and remove the fan shroud assembly. You can leave the wiring attached to the fan shround. There are a couple electrical plugs to disconnect and a ground wire near the passenger headlight that needs to be disconnected. There are two mounts on the bottom of each side of the radiator and a bolt on either side of the fan side near the top. You'll also need to unbolt the A/C condensor from the bottom edge of the radiator and support it out of the way. Be careful not to snag the radiator on the condensor or it may cause a leak. If the car has an automatic trans, disconnect the trans fluid lines from the radiator.

Jan 25, 2015 | Ford Cars & Trucks

1 Answer

Hola buenas tardes tengo un problema con mi ford escape 2009 motor 3.0 que las ventiladoras de enfriamiento se me an quedado directac y no hacen sus ciclos de parar cuando el motor esta frio si no que...


Necesitas un sensor de enfriamiento del ventilador. Est? ubicado en el radiador.

You need a Fan Cooling Sensor. It is located in the radiator.

2005 Ford Escape radiator cooling fan repair. - YouTube

? 3:19
https://www.youtube.com/watch?v=3Sk5g4PGVWs
Sep 24, 2014 - Uploaded by hufhuffy
2005 Ford Escape cooling fan problems ,cooling temp sensor auxiliary fan control unit ,radiator fan switch ...

2009 Ford Escape Hybrid radiator cooling fan - YouTube

? 1:42
https://www.youtube.com/watch?v=tRdrV825xak
Mar 8, 2017 - Uploaded by stevenofpa
00243 2009 Ford Escape Hybrid radiator cooling fan - This video shows the engine cooling fan radiator fan ...

2008 Ford Escape Cooling Fans: Both Aux and Main Cooling Fans ...

https://www.2carpros.com/questions/2008-ford-escape-cooling-fans Jun 17, 2014 - I have replaced the Main cooling fan relay but didn't help. Not sure if there is ... 2002 Ford Escape Coolant Overflow Bottle Replacement.

2009 Ford Escape Cooling Sensors, Switches & Relays - CARiD.com

https://www.carid.com > ... > Ford > Escape Results 1 - 21 of 21 - Ford Escape Replacement Engine Cooling Parts - 2009 ... Ford Escape 2009, Coolant Temperature Sensor Connector by Standard®. 2009 ford escape replace cooling fan sensor Google Search

Oct 28, 2017 | 2003 Ford Escape

1 Answer

I need to replace a serpentine belt on a 1984 Ford Bronco. Can anyone tell me where to find the belt tensioner? Also can the belt be replaced without removing the radiator fan? Thanks.


No - your belt cannot be replaced without taking the fan off. More than likely, you also have multiple belts. You will have a 1/2 inch spot on most of the plates to tighten each individual component. Look for a place to attach a 1/2 inch breaker bar/ratchet next to the alternator, steering pump, smug pump, etc. These should all be v-belts on a 1984, not a true serpentine.

May 08, 2010 | 1984 Ford Bronco

1 Answer

Need to replace the water pump on a 1992 gmc pick-up need diagram of how to replace do I need to pull the fan cluch and radiator to get to it???


hi,first off you have to remove the acc. drive belts, ac,alt.,pwr str belt etc.but loosen up the 4 bolts that hold the fan to the water pump.then remove any brackets 4 bolts hold the water pump in place and remove water hoses before removing pump bolts. clean and replace gaskets and pump reinstall all parts and added coolant .also you may want to replace thermostat.

Oct 23, 2009 | 1992 GMC Sierra K1500

2 Answers

BELT REPLACEMENT


U shouldnt need too remove the fan to replace the belt. all u need too do is work the belt around the fan blades.

Feb 09, 2009 | 1984 Chevrolet Caprice

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14398 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...