Question about 2008 Chrysler Sebring Convertible

Open Question

How do I remove rear window from my 08 Sebring convertible?

Do I have to remove the bolt from under the headliner to remove the rear window or can I just cut the window out to replace the top?

Posted by on

  • yadayada
    yadayada Dec 16, 2016

    Unless you want to really mess things up leave this to a auto trim shop!

×

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
crayzeetrayn
  • 837 Answers

SOURCE: 2000 sebring convert front /rear motor mt replacement

I would suggest you go purchase a Haynes manual .. they are great for all the DIY things .. Here's a link

Posted on Feb 10, 2009

Ad
  • 840 Answers

SOURCE: Remove and replace convertable top on a Chryster Sebring

albert I need to tell you this buddy you have saved some money on the top I would call a uphostry shop in your area they will pick up car and repalce the top for you and the window needs to be seemed in there for safety reasons call one up I hate to tell you that but. Your better off having a specailty company do this if you need anything go to collsionrepairadvice.com

Posted on Mar 09, 2009

  • 158 Answers

SOURCE: 2000 sebring transmission pan torque spec

10 ft lbs no real patterm needed

Posted on Apr 03, 2009

  • 50 Answers

SOURCE: 2000 chrysler sebring convertable top will go down but will not

Typically, when when this happens, the system is low on fluid and/or must be bled. Here are the procedures:
Lower the top to the full down position.

  1. Remove the rear seat cushion, seat back and inner quarter trim panels. Pull up sharply on the seat cushion at the front about midway between the middle of the seat and the outside edges. The seat back is held in by nuts. The quarter trim panels are held in by screws I think.
  2. Remove the cylinder mounting brackets and remove the cylinders from the trunnion pivot mounts.
  3. Rotate the cylinders 180 degrees (the hose fittings will now face to front of the vehicle.
  4. Disconnect the motor/pump retaining clips from the body.
  5. Rotate and raise the motor/pump assembly so the reservoir is in the up position. The rubber filler plug will be at the top.
  6. Raise motor/pump fitting to at least 2 inches above the horizontal rear seat back reinforcement.
  7. Tilt the motor/pump assembly to approximately the 10 o'clock position, with the rubber filler plug still at the top CAUTION: THE MOTOR/PUMP ASSEMBLY MUST REMAIN IN THE CURRENT POSITION UNTIL THE RUBBER FILLER PLUG IS REINSTALLED IN THE Step 12.
  8. Remove the rubber fill plug from reservoir.
  9. Fill the hydraulic system by adding Dexron 2 Automatic Transmission Fluid to the bottom of the fill hole CAUTION: DO NOT OPERATE THE TOP SWITCH IN THE UP (CLOSING THE TOP) DIRECTION.
  10. With two people, activate the top switch in the down (opening the top) position to fully retract the cylinder rods and hold for approximately 5 seconds, until the motor/pump stalls. A percolating or gurgle sound/feeling is an indication that the procedure is working.
  11. Top off the motor/pump with Dexron 2 and insert the filler plug.
  12. Install the motor/pump assembly into the vehicle mounting bracket.
  13. Rotate the cylinders back to the original position (hose fitting rearward)
  14. Install the motor/pump lead and hydraulic line clips (the hydraulic line clips are to assist in the production process) to ensure that the seat back/seat cushion do not pinch the lines. If the sticky side is no longer holding to the floor pan, the clips can be left off.
  15. Ensure that the bushing is still on the trunnion pivot mount and bracket. Tap the top switch in (raising the top) to get the cylinder trunnion onto the trunnion pivot mounts, if needed.
  16. Install cylinder mounting brackets.
  17. Raise and lower the top to ensure proper operation.
  18. Install the inner quarter panels, and the rear seat back and cushion.
  19. And Just a fair warning here - you WILL spill fluid inside your car. If you manage not to, I want to know how. I cover everything with garbage bags because there have been a few instances where I accidentally hit the button the wrong way and that stuff went EVERYWHERE. Be careful and good luck.

Posted on Apr 17, 2009

  • 1986 Answers

SOURCE: window off track driver side 1997 sebring

You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door

Posted on Aug 14, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you access the rear strut assembly on a 2004 Sebring Convertible? The videos show a trunk access but its not there?Is it located behind the back seat?


its in the trunk area over the wheel. you have to remove the trunk liner panel and then you can access the strut mounting bolts

Feb 17, 2015 | 2004 Chrysler Sebring Convertible

Tip

How To Install Replace Rear Power Window Regulator Nissan Maxima 04-08...


How To Install Replace Rear Power Window Regulator Nissan Maxima 04-08 1AAuto.com

on Mar 30, 2012 | 2004 Nissan Maxima

Tip

How To Install Replace Remove Rear Door Panel Nissan Maxima 04-08 1AAuto.com


How To Install Replace Remove Rear Door Panel Nissan Maxima 04-08 1AAuto.com

on Mar 30, 2012 | 2004 Nissan Maxima

1 Answer

How do i remove the rear brake rotors on a 2004 chrysler sebring convertible?


there are two bolts holding the caliper bracket on. then after that they tend to get stuck to the hub. i usually tap on the rotor with a hammer to get them loose

Jul 02, 2014 | 2004 Chrysler Sebring

1 Answer

How do you remove the rear bumper on a 2000 sebring convertable


very carefully..it is held on with clips and plastic retainers and a few bolts..some can be simply pried loose others systematically removed..a body shop can assist with info here..MAYCO

Feb 09, 2013 | 2000 Chrysler Sebring

1 Answer

When it rains my sebring convertible has water sloshing in the rear somewhere. is there a drain that empties this problem if so where is it exactly could you please tell me exactly were the drain holes are...


yes there are holes. the holes are on both sides of the back window. climb in back seat and look under the back window on the side rear quarter panel inside you will one on each side

Nov 04, 2012 | 1998 Chrysler Sebring

1 Answer

08 Sebring Convertible trunk wont latch it acts like the bar the latch is attached to has not returned to the home position?


I had the same problem on my 08 convertible. Every time I opened the trunk I was having to "bend" the upper catch to match the lower latch. I didn't want to take it to the dealer because they would charge me an arm and a leg.
Here is the quick fix:
Remove the latch plate (attched to the body with a spring) this requires a rachet and 1/2" socket or 1/2" wrench. Place 2 to 3 washers behind the latch plate over the bolts, not between the bolts and the plate. You have to be careful or you will drop the washers. Tighten the bolts and whala! the trunk lid closes and locks.
Better fix.
Get a piece of 1/8" or 3/16" metal the same size as the latch plate and drill two holes to match. Place it between the latch plate and the body to act as a shim. Replace the latch plate and bolts as described above. This method will provide better stability.
Hope this helps.

Aug 24, 2010 | 2008 Chrysler Sebring Convertible

3 Answers

How do I replace the window motor in my car? I have a 2001 Chrysler Sebring LX


take the door panel off...should be 3 bolts holding motor inplace and wiring to unplug...make sure the window is up when attempting ...its not as difficult as it seems thanks and have a good day

Nov 08, 2009 | 2001 Chrysler Sebring

2 Answers

08 chrysler sebring cruise control not working


under the hood under a black box or in the door or under the dash but more than likely under the hood

Aug 17, 2009 | 2008 Chrysler Sebring Convertible

Not finding what you are looking for?
2008 Chrysler Sebring Convertible Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...