Question about Chrysler Cirrus

1 Answer

With heat or a/c the air only blows out the defroster holes near windshield. Why will it not com out the a/c cutouts ? Is there some sort of door in there that can be stuck >

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 322 Answers

Check for any vacumm hoses broken, check for any obstuctions into the blower.

Posted on Jul 20, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Windshield defrost is not blowing out any air


A vaccume line is either cracked or broken.

Dec 17, 2013 | 2005 Cadillac STS

2 Answers

I have a 2007 dodge 2500 diesel and the heater will only heat up to a very light heat.


Mode Door 1.
a.This door regulates air flow to either the dash vents or defrost/floor. If you have air flowing only through the vents with no defrost or floor, this door is failing. From our experience, this door is usually the first domino to fail. Not sure why, just is.
<!--[if !supportLists]-->4.Mode Door 2.
a.When mode door 1 is set to divert air away from the vents and into the second stage of the system, door #2 chooses whether air goes to the defrost vents to the windshield or out through the floor vents in the passenger and driver's side footwells. Failure is indicated by an inability to choose between defrost and floor.
b.This door turns out to be the most difficult to replace. In order to replace the door, the dash panel has to be removed. It's still better than the dealer fix because you don't have to evacuate the AC system, drain the radiator, and remove the plenum box. But it is more work than the other fixes. When this door breaks, it falls in the down position, blocking the floor vents and diverting all air through the defrost vents. From a safety standpoint, this is good since you'd most likely rather have a clear windshield than warm feet. We suspect that a large percentage of customers will just leave this door unrepaired. You will have heat through the dash vents and to the windshield, just nothing to the floor. It's inconvenient, but you'll have to make the determination if warm feet are worth the extra work to fix the door. An extra pair of socks is easier.

Jan 12, 2013 | 2007 Dodge Ram 2500

1 Answer

Defroster not blowing


your blend door motor IS your defroster problem , as it is needed to direct heat mixed with the ac to properly defrost the windshield . if when you change your blend door motor and the problem still exsist , then youy have a defective blend door package , meaning one of the doors are faulty , which could get very expensive to repair , good luck !!!

Aug 21, 2012 | 1989 Chevrolet C1500

1 Answer

Little heat


Check the air divert-er door, does the air blow any harder when the panel controls are set to any other direction? If so check for blockage in the defrost vents.

Dec 13, 2011 | 2000 Cadillac Catera

1 Answer

Where is the windshield washer motor located? Is it near the heater motor? I had mine fixed and now the heat comes out of the dash for the defroster


Windshield Washer Pump Removal & Installation To Remove:
  1. Remove the air cleaner assembly.
  2. Remove the bolts. windwash.gif

  3. Position the pump and reservoir aside.
  4. Disconnect the electrical connectors.
  5. Disconnect the washer hose.
  6. Remove the pump and reservoir.
  7. Remove the washer pump.
washpump.gif

WARNING
Windshield washer solution contains methanol which is poisonous. Observe all cautions and warnings indicated on label of washer solution container.
NOTE: Windshield washer fluid should be collected in a container after the windshield washer hose is disconnected.
To Install:
WARNING
Windshield washer solution contains methanol which is poisonous. Observe all cautions and warnings indicated on label of washer solution container.
  1. Install washer pump in reservoir.
  2. Install washer pump reservoir assembly.
  3. Connect washer hose.
  4. Connect washer electrical connector.
  5. Install air cleaner assembly.
---
The windshield wiper fluid pump is located in the tank which is not in the heater motor or defroster area in the dash.

The defroster/heat control door is located in the dash board area:

Air Door Actuators, Cables or Motors Removal & Installation Air Inlet Door Vacuum Control Motor To Remove:
  1. Remove the instrument panel lower insulator cover.
  2. Disconnect the vacuum connector.
  3. Remove the control arm clip and the spring.
  4. Remove the nuts and the air inlet door vacuum control motor.
Air inlet door vacuum motor mounting screws for-10-00-245.gif

To Install:
  1. Install the vacuum motor on the mounting bracket.
  2. Connect the control arm and spring.
  3. Connect the vacuum hose to the vacuum motor.
  4. Install the lower instrument panel lower cover.
Floor Defrost Door Vacuum Control Motor To Remove:
  1. Disconnect the negative battery cable.
  2. Remove the left lower dash insulator panel and disconnect the lamp.
  3. Remove the two pin-type retainers and remove the fill panel.
  4. Remove the DLC mounting screws.
  5. Detach the vacuum line.
  6. Remove the lighting module.
  7. Remove the screws and the bracket.
  8. Remove the floor/defrost door vacuum control motor.
Floor/Defrost vacuum motor mounting screws for-10-00-246.gif

To Install:
  1. Connect the vacuum lines and install the floor/defrost vacuum motor.
  2. Install the bracket and lighting control module.
  3. Install the DLC bracket and mounting screws.
  4. Install the fill panel.
  5. Install the left lower dash insulator panel.
  6. Connect the negative battery cable.
Panel Door Vacuum Control Motor To Remove:
  1. Remove the instrument panel.
  2. Reach through the door opening and remove the pin.
  3. Disconnect the panel door vacuum control motor vacuum line.
  4. Remove the screws and remove the panel door vacuum control motor.
To Install:
  1. Install the panel door vacuum motor.
  2. Connect the vacuum line to the panel door motor.
  3. Reach through the opening and install the pin to the linkage.
  4. Install the instrument panel.
prev.gif next.gif

Jan 19, 2011 | 2003 Mercury Grand Marquis

2 Answers

98 Jimmy throws out heat but won't switch to all vent options


Your going to have to replace the switch. The switch it self may have gone bad, since it works on a vacuum. It's common for the diaphragm in the switch assembly to go bad, if it's not the switch. Then it's going to be a bad actuator door and will need to be freed up. I have found it to be the switch it self get dirty and the vacuum needed to activate the actuator door is not there.

Good luck and keep me posted. When you turn the switch from defrost to heater, do you hear a air leak??? If you do then it's a good chance that it's the switch it self.

Dec 03, 2009 | 1998 GMC Jimmy

1 Answer

Air blows only on windshield even when placed on vents or feet


you may have abad slector door acuator.which is alittle motor bolted on the heater box.It move a door in box to direct air flow to right location.hope this helps.

Sep 27, 2009 | 2000 Dodge Durango

1 Answer

No heat - ac stays on blowing through defrost vents


If you have the heater directed to the windshield, the AC will turn on. Move the control away from defrost.

Feb 01, 2009 | 1998 Ford Windstar

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

267 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...