Question about 2002 Mazda Tribute

1 Answer

The bast way to remove an alternator on an 02 tribute 4 cylinder

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Mazda Master
  • 14,204 Answers

2.0L Engine

  1. Remove or disconnect the following:

    Negative battery cableDrive beltAlternator electrical connectors and loosen the upper alternator bolt while moving the alternator to the rear of the engineAlternator. Torque the lower bolt to 35 ft. lbs. (48Nm). Torque the upper bolt to 18 ft. lbs. (25 Nm).To install:
    1. Install or connect the following:

      Alternator with the upper bolt in the alternator before installation. Torque the bolts to 18 ft. lbs. (25 Nm).Alternator electrical connectors Drive belt Negative battery cable.

Posted on Dec 17, 2016

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove the alternator in an 2001 Mazda Tribute 4 cylinder?


Disconnect battery , remove the driven belt,remove belt,remove wire and push in plug remove long bolt lift away from motor.

Aug 18, 2016 | 2001 Mazda Tribute

1 Answer

I cannot locate the PCV valve on my mazda tribute 2.3L 4 cylinder engine


It is below the intake manifold, you will need to remove the manifold to access the PCV valve

Jan 23, 2011 | 2005 Mazda Tribute

1 Answer

How do you get the alternator out?


I am trying to remove the alternator in a 2004 Mazda Tribute--I have removed the belt, dropped the crossmember, removed the exhaust under the alternator, and taken loose the axel carrier support in hopes that it would move far enough to remove the alternator but it doesn't have enough flex.

Nov 11, 2010 | 2004 Mazda Tribute

1 Answer

Timing diagram for mazda tribute 4 cylinder


You will have to remove the valve cover to align cam's, the lobs to cylinder number one should point out at 45 deg, and set crank at TDC.Hope this helps you.

265b7cf.gif1d016e6.gif

Aug 17, 2010 | 2001 Mazda Tribute

1 Answer

Replace spark plugs on a 2008 4 cylinder tribute


This is a fairly easy job. Do each cylinder one by one (removal and install), make sure to reinstall the coil on the same exact cylinder (DO NOT MIX UP). 1. Remove coil retaining scre 2. Pull upward on the coil to remove. 3. Remove spark plug (using a spark plug socket). 4. Properly gap new spark plug (if applicable). 5. Apply sprark plug anti-seize compound on plug threads. 6. Install plug. 7. Aplly coil boot grease on the coils' rubber boot tips. 8. Reinstall coil.

May 22, 2010 | 2008 Mazda Tribute

2 Answers

I can not get the alternator out


ok im a mazda tech i won a price for doing this for mazda
alot of techs were taking off the drive shaft and mazda was paying to much for the warranty labor haha

loose and remove the alternator and move it out of the way
from the alternator braket
what going to do next is remove the alternator braket its 3 or 4 bolts
remove joint shaft too
remove it completely and you can remove the alternator its a snug fit but its been done and going back in its the same prossedure alternator in first and braket next
braket torque bolts to 29 to 41 ft lbs

May 14, 2010 | 2002 Mazda Tribute

1 Answer

How to change spark plug on 02 mazda tribute


Is it a V6? For a V6 if you are standing in front of the car it will be the middle cylinder on the firewall side of the engine. You will have to remove the plastic engine cover and the intake manifold to get to it. If it were on the front side of the engine you would only have to remove the plastic cover. Since there is a good bit of work involved removing the manifold, I would suggest that you go ahead and replace all of the sparkplugs and consider replacing the coil for the one cylinder also. I have a 2001 Mazda Tribute. Mine started running rough so I decided to replace all the sparkplugs. After replacing the sparkplugs it continued to run rough. I took it to a shop and got it scanned (no cost for the scan). The scan showed the coil on the 3rd cylinder was bad. So I wound up having to pull the manifold off again to replace the coil :(
The first time it took me 1-1/2 hours to do the plugs, second time 1 hour to do the coil. Car runs great after coil replacement. Hope this helps.

Apr 28, 2010 | 2002 Mazda Tribute

1 Answer

I have an 02 Mazda Tribute with a leaking radiator.Are there any tricks in removing the radiator to repair it? The Radiator People told me that they have never done one of these before and may have to...


1. Drain coolant
2 Remove lower splash shields
3. Disconnect the lower radiator hose and the high pressure transaxle line
4. Lower the vehicle
5. Disconnect the transaxle return line
6. Disconnect the upper radiator hose and degas hose
7. Position the hood latch assembly out of the way
8. remove the 2 bolts and the center support
9 remove the 2 top bolts retaining the cooling fan to the radiator
10. remove the upper radiator support brackets, and remove the radiator from the vehicle
11. To install, reverse the removal procedure

Feb 07, 2010 | 2002 Mazda Tribute

1 Answer

How do you remove a alternator from a 2001 mazda tribute 6 cylinder


First, disconnect battery, than remove cables from starter (you may want to make mark so you don't get them mixed up when reinstalling,
Than Remove the two bolts holding starter.
Now you can pull out from top by exhaust manifold or if you have room to move through crossmember

Jun 03, 2009 | 2001 Mazda Tribute

Not finding what you are looking for?
2002 Mazda Tribute Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...