Question about Ford Cars & Trucks

1 Answer

2005 Ford f350 diesel 6.0 liter Where is the pcm location

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 1,381 Answers

This is on a 2006 don't now if yours the same
You need to remove the driver side battery and then the pcm is located on the inside of the fender just behind were the battery was and I believe that there are 2 10m bolts holding the pcm in there and unbolt it and look at the bottom of it, should have 3 letters and a number.

Posted on Dec 16, 2016

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 140 Answers

SOURCE: How do you change the glow plugs and relay in a F350 1997

Hello, here is the proceedure. Any questions please ask. Good luck. CAUTION The red-striped wires on the 1994-96 DI Turbo engine carry 115 volts DC. A severe electrical shock may be given. Do not pierce the wires.

  1. Make sure the ignition switch is OFF.
  2. For 1994-96 engines, remove the valve cover.
  3. Disconnect the wire connector from the glow plug.
  4. Using a 10mm deep socket, with enough clearance as to not break or bend the wiring connector, unscrew the glow plug from the manifold.
To install:
  1. Place anti-seize on the threads of the glow plug and screw it into the manifold.
  2. Tighten the glow plug to 12 ft. lbs. (16 Nm).
  3. Plug the wiring connector.
  4. Connect the negative battery cable.
  5. For 1994-96 engines, install the valve cover.
0900c152801cd773.jpgFig. 4: Disconnect the wire, then remove the glow plugs as shown

Posted on Jan 23, 2009

DIESELMUDDER
  • 2760 Answers

SOURCE: replace fuel pump on 03 Ford F350 diesel

simple : obtain replacement pump from parts provider (no used stuff)

Now help me out here: thats the year they were bolted to the pass side front of engine
and not inside the tank right? (better go look to see for sure)

using a tube wrench unscrew the fuel lines (i use large wire nuts to temp block off fuel leakage)

with a 12 mm wrench undo the two side bolts holding the pump to block

wiggle pump it should come straight off

clean mounting place on block with solvent let dry

silicone back (or use gasket that comes with pump ) of pump

apply pump to block (depending on where crank stopped you may have some tension on arm you will have to overcome to get flange to meet block )

use locktite (blue)or simmiliar thread lock on bolts retighten firmly but not hang up the dog tight

use light grease or vasolene on tube connections don't try to tighten dry

Now the fun part your diesel now has air in the fuel system

there are two ways to remove this ( hard and harder)
your choice here are both methods

loosten the fuel supply line for #8 injector ( I did not say remove) 1 full turn ought to be enough

crank engine 30 seconds only
wait 5 minutes for starter to cool down
crank engine 30 sec again
did it start but runs rough while it's still running tighten #8 injector (caution fuel under high pressure)
engine smooth out good your lucky
engine did not start yet
wait 5 minutes
crank engine 30 sec again
start yet
if so tighten #8 injector up

Now here's something I've done to my diesel to make this much less a hasstle

trace fuel line as it comes up from pump
obtain a small low pressure electric fuel pump and a two short pieces of fuel line
and a few clamps

use tube cutter and cut fuel line just before it bends to go in filter
deburr edges
slide tube and clamps over pipe (both sides)
insert pump observe flow arrrow towards filter

the wires of pump can be stretched over to #1 battery terminals

now any time you change a filter or open your fuel system for any reason
all you need do is connect pump to battery
open sharader valve on top of filter for a few min
and start truck as normal
then disconnect wires and stow away for another day

Posted on Jul 08, 2009

  • 56 Answers

SOURCE: 2005 ford f350 diesel charging system

take the termanals off and look inside them. Use coke to clean them.

Posted on Jul 21, 2009

  • 8 Answers

SOURCE: Need a pic veiw of 2004 ford f350 6.0L diesel EGR

1st of all when Ford started out with putting "EGR's" on those diesel engines, they rushed it and are nothing less than a pain in the ***! i recommend having an EGR cleaning service performed by your local Ford dealer, i know they charge up the wazoo, but they're the best people to perform the service period.this is a VERY common problem with those engines and that service is "supposed" to be performed every 30K I believe. i dont recommend attempting to remove and service it youself, this WILL only make it worse.

Posted on Mar 26, 2010

Testimonial: "Im relieved to here that someone else is thinking the same thing. Im still going to try it myself as i am somewhat skilled at this but Thanks a bunch!"

  • 1 Answer

SOURCE: location of pcm on 2005 pacifica?

I have a 2004 Pacifica and mine is on the drivers side front, underneath between the bumper and the wheel splash guard. You will need to remove the splash guard ti access the PCM. Not very hard at all. Replacement time for a handy DIYer: about 1/2 hour. Good luck!!

Posted on Jun 05, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2005 6.0 liter ford Diesel glow plugs how do you replace


Just below each valve cover you will find a wire harness that has 4 plugs on it. Remove each plug(becareful they get brittle over time). down in each well you will see the glow plug. there is a hex on the glow plugs. unscrew the old plugs and replace. Good Luck

Nov 13, 2012 | 2006 Ford F 350 Super Duty

1 Answer

1996 Ford F350 diesel won't start


Hi Austin, I think you hit the nail right on the head! Replace the glow plugs:-) Regards John

Oct 19, 2012 | Cars & Trucks

1 Answer

Where is the Engine Control Module located on Diesel 6.0 Ford F350 2006?


The 2006 Ford F350 Powertrain Control Module is located in the Top, Middle of the Firewall when looking under the Hood, behind the Engine.

Here is the Service Procedure with Diagram of the PCM:
http://www.4shared.com/document/jJK8SGad/2006_Ford_F350_Powertrain_Cont.html

Mar 27, 2011 | Ford F-350 Cars & Trucks

1 Answer

Where is the oil pressure switch on a 2004 f350?


the oil pressure switch on a 6 liter diesel is right behind the oil filter housing
it has a 1 wire switch the oter switch close to it is the oil temp switch

Nov 07, 2010 | 2004 Ford F350

3 Answers

I ahev a 2005 ford f350 with 6.0 diesel, i am


Bad Injectors most likely. I have a 2006 f-350 and was having the same problem. I ended up changing the fuel pump and 4 injectors.

Jan 11, 2010 | 2006 Ford F 350 Super Duty

1 Answer

1999 f350 diesel engine shut down, turns over but


that fuse powers pcm fuel heater and some other things. when the fuse blows the pcm shuts down. causing it to not run. usually its the heater that is bad. it is located at the back driver side by the fuel pump. you can unplug it and see if it starts. if so you will need to replace the heater

Jan 06, 2010 | 2002 Ford F350 Super Duty DRW Reg. Cab

3 Answers

Ford f350 diesel truck 30 amp fuse keeps blowing.


It is the fuel heater, All you have to do is unplug it.a4c0d50.gif

Dec 27, 2009 | 2000 Ford F350 Super Duty Super Cab

1 Answer

Shut 05 Ford f350 diesel off wont start


when you get a code the PCM will keep that code and till it get easased. you need a scaner or disconect your battery for 1h. this should clear your codes. when the battery is disconected don't sit in your can. the air bags may deploy if you hit the steering collem or a sensor to hard. just let it sit. reatach your battery then try to start your truck. if the codes are still pressent you make need let the car sit for longer or bit the big one and get the shop to do it.

May 30, 2009 | 2005 Ford F 350 Super Duty

1 Answer

I have a ford f350 power stoke 7.3 liter and it is blowing white smoke and it won't go above 2500rpms


Hi, I am a mechanic for a large fleet service company, i mostly work on ford 7.3 and 6.0l diesels. If you have a 7.3l that runs like **** and is blowing white smoke there are a number of things that could cause this. first is the service engine light on, if so the DTC's contained in the pcm can be very valuable in finding the cause of your problem. Most of the time you'll get white smoke and a power loss due to bad injectors, but not always. Check the top fuel filter (it is located atop the engine in the middle of the valley, it has a black cap about 4 or 5 inches in diameter). This filter being blocked could also cause the problem your having. If it is blocked with black or brown (rusty) fuel i would recommend dropping the fuel tank and checking the screens in the fuel sending unit. Let me know how you make out.

Sep 27, 2008 | 2001 Ford F350 Super Duty SuperCab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...