Question about Dodge Ram 1500

1 Answer

I want to turn off the alarm chime on 2016 1500 ram

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Dodge Master
  • 2,760 Answers

Door chime or headlight reminder chime ??? as im not in the knowing that the headlight chime can be shut off as for the door chime they can be tuned down by simply adding a few pieces of thick tape overtop of chime under dash (I know there loud)

Posted on Dec 16, 2016

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Alarm chimes 6-8 times when i turn off


i think that is a factory setting if it is a factory alarm. I have a 2001 and my horn honks once when I set it and no noise when I turn it off.(you probably have a aftermarket alarm)

Jul 18, 2014 | 2000 GMC Yukon Denali

1 Answer

Key fob don't work and chimes 6-8 times when i turn off


you have a aftermarket alarm system. you will have to take it to an alarm specialist. (it also could be a bad battery in your remote)

Jul 18, 2014 | 2000 GMC Yukon Denali

1 Answer

Interior lights on 95 grand am done went slap stupid.


Power Output Diagnostic Mode
You may use a power output diagnostic mode in the multifunction alarm module in order to run a quick test on the operation of the following outputs:
• The courtesy lamps control
• The inadvertent power control
The power output diagnostic mode activates after you perform all of following actions:
• Close all of the doors.
• Set the park brake.
• Turn the ignition switch to RUN.
Before 15 seconds pass, perform the following steps:
• Open the right front door.
• Cycle the headlamp switch from OFF to PARK three times.
During a normal operation, the multifunction alarm module will flash the interior lamps until the ignition switch turns OFF. If an internal short occurs in the multifunction alarm module, the module will chime in the following patterns:
• One chime every 3 seconds implies an inadvertent output failure.
• Two chimes every 3 seconds implies a courtesy output failure.

Sep 14, 2017 | Cars & Trucks

2 Answers

Location of tail gate alarm on 2004 Chrysler Pacifica


you may have a bad switch which is located on the latch asm

Sep 03, 2012 | 2004 Chrysler Pacifica

2 Answers

Does the bcm control the alarm in a 2006 monte Carlo? I can't seem to get the alarm to go off. I've also noticed that I have no chime and turn signal sounds. I just recently purchased this car and...


The no chime and turn signal has nothing to do with the alarm. You have a issue with power supply to turn flasher and door chime. The alarm consist of The door ajar switch,body control module,front door lock switch,power door lock switch. You need to check your fuse for turn signal and the door chime

Feb 22, 2012 | 2006 Chevrolet Monte Carlo

1 Answer

2005 silverado Z71 4X4 truck chimes while driving but no indication of what the alarm is for


This is intersting but ck and see if both turn signals are working and see if when the chime starts is the turn signal on If so it is normal your truck has a turn signal reminder chime on it and will start to chime after the truck has been driven for ablut 1 mile.If this isnt it than will need more info.

Mar 08, 2010 | 2005 Chevrolet Silverado

1 Answer

I have a 1999 Olds Intrigue, headlight left on alarm is stuck


The Body Control Module (BCM) controls the audible warnings. Refer to Body Control System Description in Body Control System for more information regarding the BCM.
The body control module (BCM) controls these reminders:
• Key in ignition reminder: An audible warning intended to remind the driver that the key has been left in the ignition cylinder. The BCM sounds the chime for this reminder at a rate of 150 chimes per minute.
• Fasten seat belt reminder: An audible warning intended to remind the driver at the beginning of the driving cycle that the driver's seat belt is unfastened. The BCM sounds the chime for this reminder at a rate of 50 chimes per minute.
• Fasten belts indicator control: A visual warning intended to remind the driver that the driver's seat belt is unfastened.
• Parking brake reminder: An audible warning intended to remind the driver that the parking brake has been left applied with the transaxle shifted out of PARK. The BCM sounds the chime for his reminder at a rate of 200 chimes per minute.
• Turn signal reminder:
An audible warning intended to remind the driver that the turn signal has been left on while the vehicle has traveled over 1.2 km (¾ mile). The BCM sounds the chime for this reminder at a variable rate (in unison with the turn lamps on) of 90 chimes per minute.
• Headlamps ON reminder: An audible waring intended to remind the driver that the headlamps have been left on. The BCM sounds the chime for this reminder at a rate of 200 chimes per minute.
• Last door closed locking confirmation: An audible warning intended to provide the driver feedback that the last door closed locking feature is active. The BCM sounds the chime for this remainder at a rate of 200 chimes per minute.
• Feature customization and diagnostics feedback: An audible feedback used when changing feature customization modes. Also used by service technicians during the BCM diagnostics. The BCM sounds the chime during the feature customization, and also during diagnostics. Refer to Body Control Module (BCM) for additional information.

Step
Action
Value(s)
Yes
No
1
Was the BCM diagnostic system check performed?
--
YES - Go to Step 2
NO - Go to Diagnostic System Check - Body Control System in Body Control System
2
Check for Powertrain Control Module (PCM) Diagnostic Trouble Codes (DTCs). Refer to Powertrain On Board Diagnostic (OBD) System Check (LX5) or Powertrain On Board Diagnostic (OBD) System Check (L36) in Engine Controls for more information.
Are there any PCM DTCs present?
--
Go to Appropriate DTC Table in Engine Controls
Go to Step 3
3
Connect a scan tool to the Data Link Connector (DLC).
Using scan tool, select BCM data display inputs and monitor the park brake switch input.
While observing the scan tool, apply and then release the park brake.
Does the scan tool indicate that the park brake input is off while the park brake is released?
--
Go to Step 7
Go to Step 4
4
Turn the ignition switch off.
Disconnect the scan tool from the DLC.
Disconnect the BCM connector C1.
Release the park brake.
Using a test light, connect between B+ and the BCM connector C1 terminal D5.
Is the test light off?
--
Go to Step 7
Go to Step 5

Your best bet ,take it to a qualified repair shop

Aug 01, 2017 | 1998 Chevrolet S-10 Pickup

5 Answers

2005 seat belt reminder keep beeping and the light keeps flashing


take wire harness apart underseat that connects to seatbelt on drivers side. then take a piece of aluminum foil and stuff it into male part so it makes contact with both prongs and plucg connection back together..problem solved!!!!!!

Jun 29, 2009 | 2004 Dodge Ram 1500

1 Answer

1997 venture keyless remote programming


SYSTEM OPERATION

System warning lamp located on top of the instrument panel
Press UNLOCK button once , turns on interior lamps and deactivates alarm (if fitted)
Press UNLOCK button twice w/in 5 seconds unlocks all doors, turns on interior lamp and deactivates alarm (if fitted)
To activate alarm system (if fitted):
Switch ignition OFF
Open driver's door
Press Lock button on remote
Close Driver door
warning lamp will flash when system is activated
Press remote power sliding door button will open sliding door (if fitted) only if unlocked first
Pressing remote panic button:
*Sounds horn intermittently
*Flashes exterior lamps
*Turns on interior lamps
**Pressing panic for the second time OR switching ignition ON deactivates alarm.


PROGRAMMING
Remobe key from ignition switch
Remove the "BCM PRGRM" fuse, from the fuse box
Close all doors
Turn ignition switch to the ACC position
With in 1 SECOND , turn the ignition switch to OFF then back to 'ACC'
(really, with in one second)
Open and close the driver's door. A chime will sound, indicating programming mode activated
Press and HOLD LOCK and UNLOCK SIMULTANEOUSLY untill a chime sounds 2 times ( about 15 seconds)
Repeat this exact procedure for all remotes to be programmed
Remove key from ignition
Refit 'BCM PRGRM' fuse.

4 REMOTES MAXIMUM CAN BE PROGRAMMED

Aug 24, 2008 | 2000 Chevrolet Venture

1 Answer

VW Golf handbrake alarm and chime


the switch under handbreak is destroy or wire of it

Jul 20, 2008 | 2006 Volkswagen Golf

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6918 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...