Question about Cars & Trucks

1 Answer

What causes the lite not to come on I changed the bulb still no lite

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 12,962 Answers

Either no power or the switch powering it is not working.

Posted on Dec 16, 2016

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change head lite 2009 buick lacurene


Check you owners manual. That will tell you.

Apr 23, 2015 | 2009 Buick Lucerne

1 Answer

I was trying to change the inside trunk bulb , not the third brake lite! Put in a new buld it would not lite.


Did you find the fuse that the owners manual tells you is 4 the trunk lite?? If its not the fuse and the light it has 2 B the wiring somewhere. Check the bulb socket with a volt meter to make sure you have voltage at the socket itself with the trunk hood up obviously. It could also be the actuator switch. Good luck!!

Aug 30, 2014 | Cars & Trucks

3 Answers

I got pulled over for my tag light being out what fuse controls that tag light?


same lite that control your parking lites. most likely the bulb has burned out. you can acces this from behind the bumper. it usuall twists to unlock the cover to the lite

Jan 20, 2011 | Ford Focus Cars & Trucks

1 Answer

Right rear tail lights only work when using turn signal or brake. Fuse under IP changed x2. What else could cause this?


its probaly the bulb it has 2 filiments 1 for the brake and turning the othr for side lites

Apr 13, 2010 | 1998 Buick Park Avenue

3 Answers

My 2006 Subaru B8 Tribeca keeps blowing headlight bulbs. In October I replaced them both for the 3rd time. They both blew out again within 2 days of each other last week. This will make 4 times. I have...


YOUR HEAD LIGHT BULBS IS HALOGEN BULBS NOT SUPPOSE TO TOUCH WITH HANDS.BECAUSE OF OILS ON THEM.THAT WILL CAUSE HALOGEN BULBS OVER HEAT AND BLOW.USE CLEAN PAIR CLOTH GLOVES WHEN YOU REPLACE HALOGEN BULBS.

Feb 15, 2010 | 2006 Subaru B9 Tribeca

1 Answer

I put new lite bulbs in and changed the head lite switch but it still blowing the head lites


you have halogen bulbs when replacing them you have to wear clean gloves on hands .your hands has oil on them it will cause bulbs to over heat and blow. you need to wear new cloth gloves.when replacing halogen bulbs.

Dec 03, 2009 | 2001 Hyundai Tiburon

1 Answer

Wiring problem left blinker does not work properly


bad ground ..trace from bulb area back to fuse block with flashers...wire is shorting to ground or ground is loose.. good luck... also... my 05 ram had wrong sized gaskets around bulbs in back causing bulbs to not last til i discovered it not sealing out the elements and replaced

Jan 07, 2009 | 2001 Dodge Ram 2500 Truck

1 Answer

2001 Chev 2500HD


Based on what you are saying I would look to see if there are any corroded or broken wires, and I would take a good look at the ground wires that are leading into each of your rear lites.
Sometimes a wire will look as though it is connected but in fact has corroded off inside of the connector.
If the trailer plug is an afterthought then I would carefully inspect each of the wires as some people use test lites that have to be poked through the insulation on the wire thus allowing condensation to get into the wire and corrode them.
At each point where two wires meet and where ever a wire go's into a connector or lite socket ( pigtail ) I would give the wire a little tug to see that it indeed is secure.
Also if you have a test lite then remove the lite bulbs and test to see if there is any power to the lite pigtail itself. I'm sure that you have physically checked each bulb itself. if notthis is rare but it does happen on occasions, a bulb will burn out and the filament in the bulb will drop down and across to the other filament on the bulb causing the lite to short out that particular circuit and this will only happen when that particular part of the circuit is powered. As I mentioned this is very rare I've only seen it happen twice in my career.
Good luck, and I hope that this info is helpfull.

Oct 14, 2008 | 2000 Chevrolet Tahoe

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...