Question about Jaguar Cars & Trucks

Open Question

Wipers ground and drivers side low beam headlight ground location on 2005 S Type Jaguar

Posted by on

  • 1 more comment 
  • Thomas Burgess Dec 15, 2016

    No I have replaced the bulb and switched the ballast from the other side. I have current there I think it's a ground problem because the wipers will work for a while then stop again.

  • yadayada
    yadayada Dec 15, 2016

    The grounds are just behind the headlights.

  • Thomas Burgess Dec 15, 2016

    Does anyone know where the ground is for the wipers I think they are connected on the 2005 S type Jaguar

×

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
j_del
  • 1586 Answers

SOURCE: burned out headlight/bulb bmw 1991 325i 2dr

It's a bulb replacement. If it's anything similar to my Audi, there is a cover on the back of the headlight housing that you pop off. Then you can reach in, pull the wire connector off the bulb, and unclip a metal retainer over the bulb, and pull the bulb out. Installation of the new one is the reverse. Just be SURE not to touch the glass part of the bulb. Skin oils can cause a halogen bulb to burn very hot and burn out very quickly. If you do touch the glass, wipe it gently but thoroughly on a cotton cloth to clean it off before you install it.

Posted on Oct 31, 2008

Ad
  • 75 Answers

SOURCE: how to change bulb on drivers side low beam head light

My niece has a jimmy, they should be the same. The inside should be the high beam, the outside the low, DO NOT TOUCH THE GLASS ON NEW BULBS! Oil will cook on them and pop them! Both come off the same way. Take off the big rubber thing. They are soft but over hard plastic. Just pull them off. If you have trouble, you can flip the little wire clips that hold the headlight housing in place, this will give you room to see the rubber caps enough to figure them out better. The bulb assembly rotates CCW counter clockwise, and should slip out easily. Take the wires and plug off. it should be obvious how it pulls off. Snap the new bulb into the wires without touching the glass part. Gently replace in backwards order as you removed it. Put the rubber caps on, they keep water off the bulbs. It will break them!

The passenger side was harder for me. I had to take the air cleaner off, the whole cover and filter.You should be able to see or feel the same type caps, The low beam outside, High beam inside. The same 2 wire clips are there to release the housing. Everything pretty much goes the same, other than the air cleaner has to be removed and replaced. And make sure the rubber cap is replaced! Good Luck and good motoring!

Posted on Dec 19, 2008

emissionwiz
  • 76846 Answers

SOURCE: one headlight brighter than other on low beam

This is caused by a dirty/corroded headlight ground to the sheet metal of the car, the ground is usually near the headlight

Posted on Feb 25, 2009

  • 7353 Answers

SOURCE: my passenger side low beam headlight is out. the

Check the fuse. There are seperate fuses for right and left. You dont mention if the high beam works for that side? If it does, the fuse is good. The GREEN wire at the bulb is the ground for the low beam. If that wire has power, then the ground is bad. If the high beam works, the hi'lo beam switch is good, and there is a problem between that headlight and the Engine Compartment Junction Block

Posted on Dec 16, 2009

  • 76 Answers

SOURCE: Low Beam Drivers Side doesn't work ... low voltage,

Power for the headlights on the Left side (High and low beam.) comes from the same fuse... The ORANGE wire and the ORANGE/BLACK are the same, they connect in the harness. If you only lack the 12v to make the light work connect them at the headlight assembly.

If your low beam also lacks ground the Left low beam ground is shared with the right low beam ground... Run a wire from left low beam DARK BLUE to right low beam DARK BLUE/WHITE.

If its not working now then your cursed, seek a witch doctor.

Posted on May 23, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Driver side headlight goes dim on high beam while passenger side is bright


bad connection or bad earth check all connection or bulb

Jan 24, 2016 | Cars & Trucks

1 Answer

Where is the fuse for the right high beam headlight for a 2005 Jaguar X Type


Headlights have no fuses since the filament inside the bulb burns out like a fuse would. If the lamp is new and is not working on one side most likely a shorted wire is present. Check for corroded terminals or loose ground wires in that area of the light

Apr 24, 2011 | Jaguar X-Type Cars & Trucks

1 Answer

Low Beam Drivers Side doesn't work ... low voltage,


Power for the headlights on the Left side (High and low beam.) comes from the same fuse... The ORANGE wire and the ORANGE/BLACK are the same, they connect in the harness. If you only lack the 12v to make the light work connect them at the headlight assembly.

If your low beam also lacks ground the Left low beam ground is shared with the right low beam ground... Run a wire from left low beam DARK BLUE to right low beam DARK BLUE/WHITE.

If its not working now then your cursed, seek a witch doctor.

May 23, 2010 | 2004 Buick Regal

1 Answer

'05 Nissan Altima Low Beam not working


Need to disconnect ground to battery before replacing light bulb or fuse will blow. Fuse is located in engine compartment next to windshield washer fluid.

Jan 06, 2010 | 2005 Nissan Altima

1 Answer

My passenger side low beam headlight is out. the driver side low beam headlight works fine. I replaced the bulb and the headlight still doesn't work. What should I look at next?


Check the fuse. There are seperate fuses for right and left. You dont mention if the high beam works for that side? If it does, the fuse is good. The GREEN wire at the bulb is the ground for the low beam. If that wire has power, then the ground is bad. If the high beam works, the hi'lo beam switch is good, and there is a problem between that headlight and the Engine Compartment Junction Block

Dec 16, 2009 | 2004 Hyundai Santa Fe

2 Answers

2002 audi s3 zenon headlight is to low is it possible to adjust it manualy if so how


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Oct 26, 2009 | 2005 Audi A3

2 Answers

How do you adjust the headlights in a 2005 Chevy Colorado?


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Jun 15, 2009 | 2005 Chevrolet Colorado

1 Answer

Need to replace the low beam headlight on drivers side


there is a cover in front of battery or ABS module depending on which bulb is blown, is held on with 2 spring clips, pop off clips, cover can be moved aside. becarefull have seen connector melt to headlight bulb requiring replacement as well. DO NOT touch the bulb by the glass.

Mar 23, 2009 | 2005 Jaguar X-Type

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jaguar Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

yadayada
yadayada

Level 3 Expert

76846 Answers

SPEEDY CAR WORK SHOP...

Level 2 Expert

489 Answers

Are you a Jaguar Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...