Question about Cars & Trucks

Open Question

What is the torque setting for a 3.0l lion tdv6 fuel injector?

Posted by on


3 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

  • 35 Answers

SOURCE: what is the torque value for tdv6 cylinder head

Hi.Looks like 15lbs/ft. according to Rave.Hope this helps.

Posted on Apr 17, 2010

  • 108 Answers

SOURCE: torque settings for fuel injectors

7Nm then 90 degree turn and another 90. New clamps and bolts are needed.

Posted on Feb 28, 2011

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How can I remove the fuel injectors?

  1. Disconnect the negative battery cable with a socket wrench and relieve the fuel system pressure. Disconnect the vacuum hose and remove the intake manifold collector from the fuel pressure regulator.
  2. Detach the fuel hoses from the fuel rail with a socket wrench and disconnect the fuel injector electrical connectors. Remove the fuel rail mounting bolts with a socket wrench so you can separate the fuel rail assembly from the intake manifold with the fuel injectors still attached.
  3. Push on the fuel injector tail piece to separate the injector from the rail. Discard the fuel injector O-rings.
  4. Lubricate the new O-rings with a small amount of clean engine oil and install the new fuel injector by reversing the removal procedure. Use a torque wrench to tighten the fuel rail mounting bolts in two stages. First, torque the bolts to between 84 and 96 inch pounds and then torque them to between 15 and 20 foot pounds

Mar 06, 2016 | 1996 Nissan Sentra

1 Answer

3,0L Ford ranger 91 want shift into over drive.did before I pulled trans to replace rear main seal in Truck.please help

Overdrive is engaged with a torque convert clutch lockup. ATF travels through the splined shaft on the transmission to the torque converter. Check the seals on the converter and the trans.

Aug 25, 2015 | Ford Cars & Trucks

1 Answer

Does anyone know how to easily remap the injectors codes on the land cruiser 3,0L d4d? i dont have any diagnostic machine and dont intend on buying one.

if you mean erase the codes, you will need obd2 scanner for 1996 to now- got one from ebay for under 20 bucks- works great

Jan 02, 2015 | 2006 Toyota Land Cruiser

1 Answer

Range rover sport tdv6 2.7

You will get your solution and all info on service info, repair info, parts info, wiring/electrical/fuse diagrams, error/fault codes, torque specs,
owner's/service/repair/parts/maintenance manuals etc everything
this website
it's a very good website for vehicle problems even as old as 1991 ford..

Feb 27, 2018 | Land Rover Range Rover Sport Cars & Trucks

1 Answer

I need to know where a fuel filter is on a landrover discovery tdv6

Hi Angie, The fuel filter is inside the fuel tank and fits onto the high pressure fuel pump. Regards Johngee10

Jul 24, 2011 | 2001 Land Rover Discovery Series II

1 Answer

Reduced performance & DCP full my wife cannot

If you own a 3.0l TDV6 Discovery 4, it requires a software upgrade for the Powertrain Control Module... Its due to a injector control error with the current software of the PCM.

Dec 18, 2010 | 2010 Land Rover LR4

1 Answer

Gas is leaking from my fuel rail (phlegm) on my number 5 fuel injector on my 1994 camaro

  • Park the Camaro on a flat, level surface and set the parking brake. Open the hood and secure it in place with the hood prop. Disconnect the negative battery cable.
  • Open the gas tank to relieve pressure on the fuel lines.
  • Remove the sight shield from the fuel injector with a socket wrench. Loosen the screws on the hose clamps and disconnect the fuel lines connected to the injectors. Keep a rag handy to catch any fuel that leaks.
  • Disconnect the vacuum hose and ignition coil wire, then unplug the electrical connectors. Remove the fuel injector mounting bolts, undo the retaining clips and remove the fuel injectors.
  • Put a thin coat of engine oil on the new fuel injector's O-ring. Place the O-ring in position, install the new fuel injectors and secure the retaining clips. Install the mounting bolts with a torque wrench set at seven pounds.
  • Plug the electrical connectors back into the fuel injectors. Reconnect the vacuum hose and ignition coil wire. Connect the fuel lines and tighten the hose clamps with a screwdriver to secure them in place. Bolt the sight shield in place with a socket wrench.
  • Place the gas cap back on. Reconnect the negative battery cable

  • Dec 06, 2010 | 1994 Chevrolet Camaro

    1 Answer

    On my 2000 Ford Windstar it appears that the two transmission fluid lines that run from the transmission to the cooler and are exposed under the front bumper are leaking fluid moreso when the van is parked...

    These can be repired by using fuel injector line and 2 hose clamps per end to assure no more leaks. The fuel injector line is resistant to high pressure and heat.

    May 20, 2010 | 2000 Ford Windstar

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    20 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Cars & Trucks Experts


    Level 3 Expert

    78289 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22326 Answers

    Thomas Perkins
    Thomas Perkins

    Level 3 Expert

    14405 Answers

    Are you a Car and Truck Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides