Question about Cars & Trucks

1 Answer

Johnson 70hp model number A J70TLESB it starts fine and revs up neutral; ok but was lacking speed unless the ckoke is held in.then just stopped, will start and rev up but die when put in gear

Posted by on

  • JAMES BAIN
    JAMES BAIN Dec 15, 2016

    when back at ome flusshing motor it will run in gear

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 15,704 Answers

I had a Evinrude 70 with the same problem. The cause was a connecting rod that wasn't clipped on the carb linkages. It is just to the left of the automatic choke. Unless this little clip is in place, you are only operating on one carb. Operate the throttle and make sure all three carbs are moving.

Holding the choke in, overgasses that one carb that is working fine.

I have a picture on my computer at home. Let me know by way of COMMENT under my post if you want to see it.

Posted on Dec 15, 2016

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

After running my johnson 4hp 2s for a couple of hours in the bay it starting giving a strange noise and then cut out.i managed to get it started again but coudnt get above half speed.


Hey Pete.. this sounds serious.... will it rev up while in neutral? If it revs freely and high.. the power head should be ok.. if it will NOT rev up freely and high.. STOP - you are causing more damage..
Check the compression with a good gauge..it should be 125psi minimum.. with no more than 10 psi difference between any two cylinders.. DO this WITH the THROTTLE WIDE OPEN...
Can you turn the propeller by hand while it is in neutral?..Of not.. this is the problem.
Shop Evinrude Outboard Parts Johnson Outboard Parts
Lower Unit Replacement Rebuilt Lower Units Aftermarket Lower Units
REMANUFACTURED LOWER UNITS
https://www.boatengine.com/lower-units/remanufacture
Refurbished Lower Units for Yamaha Mercury OMC Johnson Evinrude

Jul 09, 2017 | Cars & Trucks

1 Answer

94 blazer 1500 starts idles or rev to 5000 when in park or neutral. in drive idles ok but stumbles and dies when you accelerate under load.it takes awhile to reach 75 mphd it will kick down to climb a hill...


You either have a defective idle speed control valve or you have a huge vacuum leak on the engine like an intake manifold or warped throttle valve or throttle bore opening around the throttle valve, I have seen both...

Jan 08, 2017 | Cars & Trucks

1 Answer

Engine starts and idles fine, but will not rev up (2001 Jeep Grand Cherokee 3.1 diesel auto)


If it was a fuel shortage the engine would rev but to limited speed. This is a lack of air to throttle body. Check for clogged air filter and all the piping and the throttle body.

Sep 28, 2012 | 2001 Jeep Grand Cherokee

2 Answers

My 2002 dodge durango hits 4000 RPMs and bounces between 3000 and 4000 RPMs when I am in park and have the throttle held down. I replaced the cam sensor and it is still doing it.


this is your rev limiter stopping you from over reving engine causing internal damage. this is normal on all new vehicles. Don't know what year they started this but it goes back at least 16 yrs

Mar 02, 2011 | 2002 Dodge Durango

1 Answer

Starts O.K. Lacks pulling power. Will not rev to full power.


check for a clogged exhaust look at catalytic converter it could be stop up.

May 24, 2009 | 1999 Suzuki Vitara

2 Answers

Loss of power


I have the same problem on a s320 cdi, gearbox goes into limp mode and wont rev above or kickdown, at the 1st chance i get to stop i put into park or neutral gear turn off the engine and re-start and then everthing is fine, I read that if you put a new battery on it may solve the problem, it's something to do with the voltage dropping below 10.4 volts. Then it sends a message to e.c.u. that puts your gearbox into limp mode. Hope this will work for you. MERKY

Apr 25, 2009 | 2005 Mercedes-Benz Mercedes Benz E320 Cdi

1 Answer

Taurus 2003 idling problems


mcdevito75 here, Sounds like the idle speed motor, Ford is known for these idle speed motors going bad, in the later stages the car races like crazy. have your repair shop check this idle speed motor and change it.

Mar 14, 2009 | 2003 Ford Taurus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

26 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...