Question about Cars & Trucks

Open Question

Can the back be removed from a Jackson catnapped omni lift chair?

Need to remove to fit in room

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
dgjtex
  • 405 Answers

SOURCE: how do i replace the

there is either a 10 mm or 13 mm bolt on one of the long sides of the battery that clamps it down, also there may be a brace from you core support to fender that will need to be removed

Posted on Dec 15, 2008

Ad
  • 105 Answers

SOURCE: oil pan removal for 1994 k1500 4WD

You should be able to drop the front drive and pull the starter you should be able to drop the oil-pan without to much trouble

Posted on Mar 25, 2009

goofduck
  • 490 Answers

SOURCE: trying to remove fuel filter does fitting on back end of filter need a specal tool to remove it .I fnot how can it be removed?

yes it is a spring loaded connection you can buy them at the auto parts stores

Posted on Apr 27, 2009

countrysi248
  • 443 Answers

SOURCE: Need to haul power chair and scooter at the same time

If it were me I would make the rear landing bigger instead of having that scooter inside with me .. incase of an accident I wouldnt want that in the car floating around.. you could have a welder make your rear lift a little larger and put a small ramp on it for the scooter also.. just a idea.. thanks Jerry ..

Posted on May 13, 2009

  • 713 Answers

SOURCE: Need to remove tail gate lift assists.

pretty easy to do find the ends of the lift support should have a clip on the back side of where it connects pull clip out and remove shock.

Posted on Aug 30, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How dowe fit a new leasure battery onour camper van please how dowe remove thepassengerseat


dont believe the design would make you unbolt the chair and remove it

will be either by sliding the chair right back
look for releasing the metal clips catches at the floor pan
as the chair is moved right back
then maybe tilting



26212407-oaabsiacwf3ritpak1e5e5z5-2-0.jpg

Jun 04, 2016 | Cars & Trucks

1 Answer

How do i adjust the paasenger seat in my 1999 VW beetle?


There is a D shaped handle on the side of the seat nearest the door. Lift up on it and the seat back will fold forward, and the entire seat mechanism will lift up and to the front, giving your passengers room to get into the back seat. Simply push the seat back toward the rear of the car to set it back in place; it will lock itself down once it's back in its original position.

May 16, 2014 | 1999 Volkswagen Beetle

2 Answers

I am trying to replace the console light on my 2006 pt cruiser and i am having trouble lifting it off and over the hand brake handle and shift lever.. it binds on both seats as i lift it up. do i have...


Turn the key on, move the gear shifter into low position, lift console slightly the reach your hand under the console and pull on the e-brake handle until you are able to lift off console.

Feb 06, 2011 | 2001 Chrysler PT Cruiser

1 Answer

To remove 1993 mustang conv. top cylinders should top be up or down? thanks, bill


don't have 93. here's 94

Motor Assembly, Convertible Top Removal and Installation
NOTE: The folding top hydraulic cylinder rods should be in the fully retracted position.
Use absorbent rags or a container to catch any hydraulic fluid that leaks out when removing the fittings.
  1. Remove motor and pump assembly as outlined.
  1. Loosen each folding top motor upper and lower hose fitting on the sides of the folding top hydraulic lift motor and plate kit (533A00) .
  1. Remove the folding top hydraulic lift motor and plate kit .
  1. Remove each of the service folding top hydraulic lift motor and plate kit plugs one at a time and attach the tee fitting to the replacement folding top hydraulic lift motor and plate kit . NOTE: Make sure that the o-ring is installed in the bottom of each folding top hydraulic lift motor and plate kit port before attaching the hose tee fitting.
  1. Connect the folding top hydraulic lift motor and plate kit unit to a 12-volt power source and cycle the folding top hydraulic lift motor and plate kit in and out several times to purge the air from the folding top motor upper and lower hoses (53390) . Some noise squeal may be noticed due to the air. srb~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not overfill or the reservoir seal could be blown out.
  1. Carefully remove the rubber fill plug from the back and the reservoir and check the fluid level. The level should be at the bottom of the filler hole. If necessary, add Synthetic MerconĀ® Multi-Purpose Automatic transmission fluid E6AZ-19582-B (ESR-M2C163-A2) or equivalent.
  1. Replace the fill plug with a new fill plug.
  1. To install, reverse Removal procedure.
-------------------------------------------------------------------------------------------------------------------------------
Section 01-17: Convertible 1994 Mustang. Workshop Manual
REMOVAL AND INSTALLATION Lift Cylinder, Power Top Removal and Installation
NOTE: The cylinder rods should be in the fully-retracted position.
  1. Remove pump and motor as outlined.
  1. Remove the upper and lower hose fitting from the folding top hydraulic cylinder (50600) . Use absorbent rags or a container to catch any hydraulic fluid that leaks out when removing the fittings.
  1. Remove each of the service cylinder plugs one at a time and attach the hose fittings. NOTE: Be sure each fitting is installed in the correct position on the folding top hydraulic cylinder .
    NOTE: Make sure that the tetra seal is installed in the bottom of each of the folding top hydraulic cylinder ports before attaching the upper and lower hose fittings.
  1. Connect the folding top hydraulic lift motor and plate kit (533A00) to a 12-volt power source and cycle the folding top hydraulic lift motor and plate kit in and out several times to purge the air from the hoses. Some noise squeal may be noticed due to the air.
  1. Carefully remove the rubber fill plug from the back and the reservoir and check the fluid level. The level should be at the bottom of the filler hole. If necessary, add Synthetic MerconĀ® Multi-Purpose Automatic transmission fluid E6AZ-19582-B (ESR-M2C163-A2) or equivalent.
  1. Replace the fill plug with a new fill plug.
  1. To install, reverse Removal procedure.

Jan 21, 2011 | Ford Mustang Cars & Trucks

1 Answer

How do I remove / fit the rear seats of VW Vento Highline Petrol MT.


The bottom cushion lifts up from the back..
Pull it forward then unclip the two hinges from the front.
The back seat has has two to four bolts on the bottom. These need to be removed.
Once the bolts are removed, lift up the back cushion.

Oct 20, 2010 | Volkswagen Jetta Cars & Trucks

1 Answer

Removal procedure of oil pan for a 1997 chevy


To remove the engine oil pan either the engine has to be lifted all the way off of the motor mounts and the oil pan should just clear the flex-plate and transmission, or the front axle dropped down out of the way, or the transmission and flex-plate will have to be removed.

Usually if the engine can be lifted enough to fit a piece of 2x4 wood between the motor mounts and the frame then the oil pan will usually just have enough clearance to be removed from the rear and the oil pan should just clear the transmission and the flex-plate. Also, be sure to check that the fan blade does not damage the fan shroud when lifting the engine.

Let me know if you require any further assistance.

Jul 26, 2010 | 1997 Chevrolet Tahoe

1 Answer

I need to replace the back seat on my 2005 toyota crolla CE


to remove back seat put front seat forward look for a latch then pull it and lift if no latch push seat mase backwards and lift at same time it will come out

as for what filts call local salvage yard they know what fits and what doesnt

Jan 01, 2010 | 2005 Toyota Corolla

1 Answer

Need to haul power chair and scooter at the same time


If it were me I would make the rear landing bigger instead of having that scooter inside with me .. incase of an accident I wouldnt want that in the car floating around.. you could have a welder make your rear lift a little larger and put a small ramp on it for the scooter also.. just a idea.. thanks Jerry ..

May 13, 2009 | 2004 Honda Odyssey

2 Answers

How to change headlight bulb on ford mondeo


Very easy, 2 or 3 minutes.
Remove radiator grille. 2 plastic fittings on top, quarter turn and lift out grille.
Remove complete headlight. Simply lift out 2 L shape retaining pins. Disconnect lead. Ease out complete headlamp unit.
Remove back of headlamp unit to access bulbs. Disconnect lead from bulb while bulb still held by clip. Then release clip to remove bulb.
Reverse process to fit.

Jan 02, 2009 | 2001 Ford Focus

1 Answer

2001 VW Passat AUG Oil Pump replacement - how to get around support beam


Best thing to do is to undo the engine mounts and lift the engine up. You can use an ond seat belt and a strong peice of wood that will fit accross the engine bay. You can use a tie-down ratchet as well to lift up the engine as it will make things easier. then you'll have more room to remove the pan. Cheers.

Nov 10, 2008 | 2001 Volkswagen Passat

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

77202 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...