My Pride Quantum Edge mileage odometer is stuck on 213 miles. Is there a way to reactivate it?

There is no fuse for just the odometer, has main fuses for the whole instrument cluster . Odometer not working? instrument cluster problem. Have it checked by a professional repair shop.

Odometers
Each instrument panel cluster (IPC) is equipped with a season odometer and 2 trip odometers. The IPC uses the odometer rolling count message from the powertrain control module (PCM). The rolling count value is determined by counting the speed pulses from the vehicle speed signal (VSS). The IPC uses the rolling count data from the PCM and a software program to determine vehicle mileage. The odometers can be displayed in miles or kilometers. The units displayed is switched between English and metric by pressing the menu button on the driver information center (DIC) until the units mode is displayed. Pressing the set/reset button will select between English or Metric. . When the set/reset button is pressed to show the odometer in metric, km and the number will be displayed. When the odometer is in English, MI and the number will be displayed.


Season Odometer
The season odometer displays the total accumulated miles or kilometers of the vehicle. This value is permanently stored in the IPC. If an odometer malfunction occurs or if the IPC must be replaced, an authorized Delco service center must be contacted to program proper vehicle specifics, including mileage, for the IPC. The season odometer is capable of displaying 999,999 kilometers or 999,999 miles depending on units selected. Leading zeros are not displayed. The display will not roll-over to 000,000 if the maximum displayed miles or kilometers are reached. If the display limit is exceeded, the maximum value (999,999) is displayed. If the mileage is above 621,503 miles and metric units are selected the odometer shall display 999,999 km.


Circuit/System Testing
Ignition OFF, raise the vehicles drive wheels.
Engine ON, transmission in drive, verify the scan tool Vehicle Speed Sensor parameter matches the speedometer display.
? If the Vehicle Speed Sensor parameter does not match the speedometer display, replace the IPC.
Verify that the odometer is operating properly.
? If the odometer is not operating properly, replace the IPC.

I am thinking you mean a Mobility scooter rather then a Ford Edge 2 litre? Full 'make model (what it is)' in all questions please. We also have a Quantum category.

Have the batteries load tested. An Interstate Battery shop will do the test for free in 2 minutes.

Q6 Edge 2.0 Power Wheelchair - HME Mobility & Accessibility

https://www.hmebc.com > ... > Power Wheelchairs
With features like standard 6 mph motors and advanced responsiveness, the Q6 Edge® 2.0 is engineered to meet the performance needs of the most active.
Seating Sizes: TRU-Balance® 3; Synergy®/St...
Weight Capacity7: 300 lbs
Battery Charger: 8A Off-board
Base Weight: 138.6 lbs

Quantum Q6 Edge 2.0 Power Wheelchair Base - Vital Mobility

https://www.vitalmobility.ca > Quantum-Q6-Edge-Powe...
The Quantum Q6 Edge 2.0 Power Wheelchair is engineered to meet the demands of the most active users. Standout features include 6.25 mph motors, ...
Seat Dimensions: TRU-Balance® 3; Synergy®...
Overall Weight: 138.6 lbs (base only)
Seat To Floor Height: TRU-Balance® 3; Syner...
Top Speed: 6.25 mph

Odometer
The odometer is an electronic digital display. Digits displayed are illuminated by the odometer backlight bulb. The odometer backlight bulb brightness is controlled by class 2 messages from the BCM to adjust the display for daylight and instrument panel dimming operation. The trip odometer and total odometer will show in this display area. The push button in the lower right side of the speedometer is used to toggle between the trip and total odometer readings. To reset the trip odometer, push and hold the button down for at least two seconds. The total odometer display has six digits with no decimal display. The trip odometer has four digits including a decimal point and indicates tenths of a mile or kilometer.
The body control module (BCM) stores the vehicle mileage. If the BCM fails, the cluster will display the last valid mileage that was sent before the BCM failed. For replacement of the BCM refer to the BCM section of this service manual. Replacement instrument clusters do not require odometer pre-setting before installation. If the instrument cluster is replaced, the mileage stored in the BCM will be sent to the new cluster via serial data, and shown in the odometer display.

Your best bet , take it to a qualified repair shop.

A magician might be able to do that, but no mechanic can. Whatever miles is on the cluster from the previous car-that's what your "new" mileage is. Write it down when installed, then you can always figure the true miles on your car and engine by comparing the old cluster's odometer with the new one. See? The old odometer is the true mileage. Whatever miles you put on the new odometer should be added to the old odometer's miles to give a true mileage of the car and engine.

the 10,000 gear has worn out. Even if you could somehow "jog" the odometer
to the next number, it would likely
encounter the same problem trying to transition from 149999 to 150000.

Your option is replacement, or do what 99.999% of car owners do when the Odometer quits - ignore it.
Or set the trip odometer to zero, and never touch it again - thereby you can calculate the
total mileage by adding the trip odometer value to 140000.

Knowing the current odometer mileage is valuable for a Honda Accord owner with 140K miles, since
you want to keep up the regular maintenance intervals for your car - if you do, you 97 Accord
will likely travel past the 200K miles mark, and eventually approach 250K miles (like my Accord).

It is illegal to change the Cluster or modify the odometer reading , unless the mileage on the cluster in your car now is documented, the mileage and date of the new cluster when installed is also documented. You do not have to change the cluster just because you change the motor. The mileage only is there for the vehicle not for the engine. Hope this helps, Not sure if you were asking about the legal aspects. Cobra.. :-)

Sounds like the plastic plunger is damaged or had dislodged from its hole. Try wiggling it as you push gently. If this works than it is damaged or warn to the point that it misaligned with the hole.

You will need to pull the speedometer out and have the odometer (u call mileage counter) repaired, the little drive gear that comes off the speedometer to operate the odometer has failed or broken.

mostly you need a new cluster so you need to find one with the same mileage or close to it look in the junk yard its cheaper and you can get lucky to find one with the same miles

It is actually impossible to change the mileage on that odometer. The ONLY way to insert a new mileage number is to completly replace the insturment cluster, and reprogram the mileage with the GM scan tool. Once the car has even .1 miles on it, you can not change the clusters mileage.