Question about Pontiac Sunfire

1 Answer

My car, signal lights and indicator lights won't come on. I have change the fuse and still not working

Posted by on

  • average_joe6 Jul 20, 2009

    I've also checked the relay and its also good. 

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 336 Answers

Hi, It could be the relay. Please try to locate the relay (usually it is also in the fuse panel, but could be different on your car, just please use you manual to locate the relay), pull it out and inspect for any burnt indication. You may swap it with the same relay in your fuse/relay box then try if it will work. Please buy a new relay if you'll find it is defective or burnt.

Cheers!

Posted on Jul 20, 2009

  • jessy Jul 20, 2009

    Hi, Then I think you have a broken electrical line/wire. Unless you have busted all of you signal lights and bulbs, but that would be unlikely to happen. Still you need to add that to the checklist.



    1. First, try to switch on signal light (either left or right) and hear if the relay is ticking (you've mentioned that relay is good, how did you test that). If the relay is ticking, then you relay is good.

    2. If relay is good then, your problem is connection between battery-relay-light. You need to get a diagram of you relay. Measure the terminal that connect battery to relay, you should be reading 12V or 24 V, if none then wire between battery and relay is broken. You need to find the broken connection, or just replace the wire (that could be tough one).

    3. If connection between battery and relay is OK, then you need to check if the voltage from relay is being relayed/switch to you bulb. You should be measuring same valtage as you have measure at relay terminal, if none then connection between relay and bulb is broken. You will need to find the broken wire the connect it or just replace the wire connection.



    kind regards.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What fuse controls the indicator lights on the instrument panel


If the signal lights are working the fuse will be good. If none of the lights are working on the dash it will be a fuse. Try gently moving the signal light arm up/down just a tiny bit to see if the indicator light/s will come on. If they do, suspect a signal switch

Jul 20, 2015 | 2005 Dodge Caravan

2 Answers

Need to fine the fuse for the left turn on a 1999 w900 kenworth


only has one fuse for turn signals . if both left turns do not work it is most likely in the turn signal switch.

Jan 29, 2013 | Cars & Trucks

1 Answer

Indicator lights dont work but the rest do bulbs have just been changed where will i find fuse for mazda mpv 2002


Are you refering to your turn signal indicator lights? Do your turn signals work on the front and rear of the vehicle? If so, the problem is NOT a fuse.

If you are not talking about your turn indicators, I would need further explaination before I could tell you where any fuses are located

Please also review this article and post a "comment" if you would like further assistance:
Where's The Fuse?

Aug 28, 2011 | 2002 Mazda MPV

1 Answer

I have a 2002 honda accord when I push on the brake padel my turn signals or my 4 way flashers won't work. When I put on my lights my turn signals or my 4 way flashers won't work. Could you please...


Hi,
First check the fuse in the fuse box for signal light, replace the fuse with similar value if it is busted. If the fuse is still intact the problem would be the flasher relay( small cylindrical aluminum ) that is already malfunctioning.

Hope that helps you out!

Aug 07, 2011 | 2002 Honda Accord

2 Answers

My brake light is on while driving and my turn signal lights are not coming on


there are several causes, check bulbs first. A crossed filament in a bulb can cause similar problems. The brake & turn use the same filament so if the brake lights are on, due to a bad switch underdash, the turn signals won't work.

Jun 08, 2011 | 1997 Pontiac Grand Am

2 Answers

1992 Cadillac Brougham 5.0 L V8 RWD, turn signal don't work.


The turn signal switch is most likely the problem,but change the flasher for the turn signals first,some times this is all that it is.

Jun 11, 2010 | 1992 Cadillac Brougham

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

65 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...