Question about Cars & Trucks

1 Answer

Removing tailshaft from gearbox on VS commodore

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 79,865 Answers

Unbolt it from the differential flange and it just pulls out of the end of the transfer case

Posted on Dec 14, 2016

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What causes the rubber donut in the rear of my ve commodore not line up with the diff but lines up with tailshaft


Don't worry I'm sure you will get the solution of your problem, just check the link I attached
ve commodore

Dec 12, 2017 | Cars & Trucks

Tip

Vs commodore series ute manual gearebox removal 2000 model


<ol> <li>Jack car up and place on chasis stands on all 4 wheels</li> <li>remove battery</li> <li>drain transmission oil</li> <li>remove electrical coneecters on gearbox..(2 on the gearbox and 2 for oxygen connecters-remove all attachements from gearbox and zip tie wires on engine block away from the gearbox as these can get caught and split)</li> <li>using a deep 13mm socket remove exhaust flange nuts and 19mm for the mid section-pull exahust out </li> <li>Mark alignment of drive shaft in the middle where it attaches to the rear half</li> <li>Place a jack under gearbox and remove mounting plate</li> <li>remove bolts from drive shaft on gearbox end and slide spline out-no need to remove the complete drive shaft from up to the rear.Only 1/2 will do.</li> <li>Looking up from underneath there are 4 bolts holding 2 plates from the place the gear lever sticks out .remove bolts and using a flat screwdriver push locking clip out to completely free gear linkages(no need to do it from inside)</li> <li>remove slave cylinder (13mm)and zip tie it out of the way</li> <li>remove starter motor</li> <li>place a bigger trolley jack under the gearbox and undo all bell housing bolts(19mm &17mm)NOTE:you will need longer extensions for this</li> <li>put another jack under engine</li> <li>using a pry bar make a gap between geabox and engine block and with a little bit of elbow grease push gearbox out of the way</li></ol> <br /> <br />

on Aug 08, 2011 | Ford Aspire Cars & Trucks

1 Answer

I want to replace the tail shaft carrier support bearing in my automatic gearbox 2006-7 BT-50 with the correct system or better?


I am wondering what tailshaft bearing your gearbox is currently using that your question implies is incorrect?

Apart from heavy commercial gearboxes and 4wd off-roaders the only gearbox tailshaft bearings I have seen are plain thin-wall bronze types that once installed must be line-reamed or broached for a good fit with the propeller shaft or drive flange. So far I have only heard about folk needing them changing. In 40 years I have never seen one that has given trouble.

Mar 06, 2017 | Cars & Trucks

2 Answers

How to install starter motor for VS commodore


I suggest you pose the question on the VS section of the Just Commodores Forum and one of the guys there should be able to help you with that.
Here is the link to the website........................


Forum VR VS Holden Commodore 1993 1997



======================================================

Apr 24, 2016 | Cars & Trucks

1 Answer

I was talking about a vp commodore v6 manual can I put either a vr or vs manual tailshaft in my vp manual commodore v6


join a Commodore forum
and win.
only real forums have SWAPS page, this form here is brain dead.
no structure. (besides, cars and trucks)
google that, see em..... ok?

Jun 27, 2014 | Cars & Trucks

1 Answer

How do I dismantle tailshaft support bearing ve commodore


This will be detailed in a repair manual but basically remove the rear section tail shaft if flanged . If not remove the whole shaft from the car and disassemble the shaft joints near the bearing. Remove the nut and pull / press the bearing from the shaft. It should come as a complete item (bearing ,rubber mount and mounting case). Take care to mark where the flange /section comes off the splines as it is critical to position it exactly on reassembly to prevent vibration of the shaft.

May 02, 2014 | 2006 Holden Commodore SS

2 Answers

Vs ecotec vs commodore engine light comes on after driving


I have no dash lights so at night I can only use the speed set to let me know what speed im doing how do I fix them in 95 vs commodore

Sep 16, 2012 | Lexus GS 300 Cars & Trucks

1 Answer

Replacing rear seal in gearbox


Nope.Not sure about yours but 95% of the tailshafts that I know,just slide out.Best you change the rear oil seal at the same time.Best time to do it.Hope this helps

Dec 04, 2009 | 1986 Volvo 740

1 Answer

How to remove tailshaft on 46re auto transmission


2wd? If you remove the tailshaft you will be removing the whole overdrive assembly. I would try pulling the driveshaft and seal. Then see if you can remove and install a new bushing. It is quit a bit of work to reinstall the overdrive unit.

Apr 04, 2009 | 1999 Dodge Ram

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

john h

Level 3 Expert

14445 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...