Question about Cars & Trucks
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
Try Super Heavy Duty Lock Tight and attach it to the fuel door. Make small hole to feed the end of spring into then glue it down tight.
Posted on Jan 27, 2009
SOURCE: Trunk latch pull down
You could try setting release to work manually. I have had the same problem. Take tne motor off set the catch clip at the right height. This should work with no cost.
Posted on Jun 04, 2009
First, take off the license plate.
Since the hatch wouldn't open, I started from the inside and took down the top trim piece. After that the two side pieces come down, then the main trim piece which covers the bulk of the door comes out. These are all popped in with the white tabs.
There are 3 access hole covers to pop out (don't forget to install them back in when done) and through the left hole you can see the mechanism to unlatch, press it down with a screwdriver and open the door. If anytime you close the door you will have to do this to unlatch, up until you disconnect the cable and pull out the handle, then you have to locate the cable and pull that directly.
Behind the large trim piece you will find a metal access cover, remove the 7 or 8 10mm bolts holding that on and pop the 3 white tabs and let it hang off to the side. Disconnect the cable from the handle assembly by reaching in from the right hand side and popping of the cable from the handle assembly.
From the left and right access holes, locate the two 10mm nuts which hold the license plate assembly to the door and remove them. Then there are 4 plastic tabs that come in from the outside that hold the license plate assembly on in each corner, try and locate those and using some pliers squeeze them together and push it through. Next locate the license plate lamps wire connector and release that from the left side, it’s the simple push in and pull out square white connector.
After these are out, put back in 1 or 2 bolts into the large metal access cover so the hatch can be lowered (don’t close it).
Here is where I had fun, begin to pop out the assembly that it was bolted to. I ended up breaking 3 of the 4 plastic tabs in each corner because I did not use pliers from the other side to pull them out, however it remained somewhat useable (hindsight 20/20).
Now the license plate assembly can be taken to a bench to replace the handle assembly (Toyota doesn't sell just the handle, it is a small assembly). Two screws out and the assembly is replaced.
Before pressing the license plate assembly back onto the truck, make certain all the plastic tabs are in the assembly and not in the truck. Reverse the process to re-install.
Posted on Dec 12, 2009
You might try having a friend bump the gas cover with the heel of their hand while you **** briskly on the release. Have done this a couple of times and once opened, you can use a little lubricant on the exposed parts. Sometimes that is enough.
Posted on Jan 09, 2010
Tips for a great answer:
Aug 28, 2011 | 1994 Cadillac DeVille
May 27, 2011 | Audi A4 Cars & Trucks
Jan 24, 2011 | 1993 Oldsmobile Eighty Eight
Sep 24, 2010 | 1994 Pontiac Sunbird
Feb 21, 2010 | 2004 Honda Civic
Jan 31, 2010 | 2007 Honda Civic GX NGV Sedan
Nov 21, 2009 | 2003 Volvo V70
Oct 15, 2009 | 2002 Jaguar X-Type
Feb 08, 2009 | 2004 Honda Civic
15 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: