Question about Infiniti Cars & Trucks

Open Question

Are there any other makes and models that would be compatible with the 95 infiniti brake proportioning valve

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

fastboyz
  • 674 Answers

SOURCE: did brake job on 1992 chevy pickup, how do I release proportional valve?

some times you get an air bubble and you just cant get it to pass. you can work very hard and still not get it to bleed. snapon sells a bleeder system that sell for around $500 but i can tell you how to build one for under $20. if interested. but your answere is to back bleed the system from the farthest away wheel first. and then your peddel will come back.

Posted on Aug 23, 2008

askjhuber
  • 59 Answers

SOURCE: Where can I find a brake proportioning valve for my 97 S-10?

When people tell me they hate there ABS, alot of people who pull trailer do. I tell them just to pull the fuse this will stop them completely. Yeah theres a light ont he dash but that can alos be delt with by removing the bulb for it. But int he long run just pulling the fuse is quick and Free.

Posted on May 17, 2009

  • 599 Answers

SOURCE: the ABS/proportioning valve is not working.

these trucks need a seperate bleed procedure for ABS you need a scanner to put it into this bleed mode,hope this helps if not get back to me and we'll go from there. please rate my fix as i strive to be the best

Posted on May 19, 2009

juncro
  • 467 Answers

SOURCE: Proportioning valve leaks brake fluid.

yes you must change same, in my experience i change it

Posted on Jul 31, 2009

  • 192 Answers

SOURCE: The brake light is on

The proportioning valve simply ensures that the front brakes are applied before the rear brakes are, to prevent sideways skids from loss of rear traction. The valve also serves as a warning light when one end, either front or rear, of the system has deficient line pressure. Inside the valve is a cylinder, and a piston that belongs in the center of the valve cylinder (when fluid pressure on each side is equal). When one side of the valve (front or rear brake system) loses pressure (like from a leaking brake line), the piston gets pushed to the low pressure end and makes contact with a switch terminal that turns the light on.The trick to turning the light off is to figure out which end, front or rear brakes, the piston is on, and then bleed the other end to center the piston and turn the light off. Too much pressure on the brake pedal will cause the piston to go past center to the opposite end, and a close watch on the brake warning light will reveal that as the lamp will flicker once while the piston passes center.
Gently depress the brake pedal (requires an assistant) with a bleeder open and close the bleeder as soon as the assistant (brake pumper) sees the light go out. If he sees the light flicker once bleed the other end of the vehicle to go back towards center.

Posted on Jul 23, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where can I find the brake control valve


didnt specify vehicle --generic answer --brake control valve ? if you mean the proportion valve [disc brake systems] follow brake lines down toward frame and after abs control will see a small valve that the brake lines go into and than disperse to front and rear if this is not the valve your looking for please edit or repost with more information year make model and better description of part

Sep 05, 2016 | Cars & Trucks

1 Answer

What does the proportioning valve do?


Assuming you're talking about the brake system...
The proportioning valve is on the rear brakes only when the vehicle has rear Drum Brakes.
What it does is limits the brake line pressure to the rear brakes during normal stopping. This way the rear brakes don't lock up and cause the vehicle to fish tail or spin.
When you press the brakes harder than normal, the proportioning valve opens more to allow more line pressure so you're able to stop faster.

Jul 10, 2014 | 1983 Jeep CJ7

1 Answer

Rear brakes lock when press brake pedal.


get is serviced.

its stuck in , low bed (loaded) mode. the lever is or parts in side

stuck in full load mode.

and guess what, if you bypass the valve, what will happen

the rear brake will lock, going fast and if on wet or worse roads. 10x worse. its there for a reason. to lower the brake pressure with no pickup bed load. or not heavy trailer tongue weight.



ever consider the rear brakes are bad. first. and not the valve.



service the rear shoes and slaves.

then check the bypass.



Does the truck still have the height sensing brake line bracket and line connected into the prop valve?



http://www.jeepforum.com/forum/f53/bad-proportioning-valve-any-ideas-1127468/#post10505224







here is the valve.

sold at , JEEP.



http://www.factorychryslerparts.com/products/JEEP/1988/COMANCHE/VALVE--Proportioning--VALVE--Proportioning--ECE-198789--1989--Except-France--Italy--1990--KDX--KDX-After-3-1-93--KDX-Up-to-3-1-93/4520728/52009114.html



Chysler p/n

52009114 ; 52003118



google that and find them for $75

Feb 16, 2014 | 1988 Jeep Comanche

1 Answer

Brake proportioning valve


H Colin, The brake proportioning valve adjust the amount of effort required for maximum efficiency with different loads in the vehicle. The brakes in most vehicles are proportioned for approximately 60% front brakes and forty percent rear. The valve makes small adjustments to braking between front and rear. Regards john

Jun 16, 2013 | Ford Taurus Cars & Trucks

1 Answer

Not getting break fluid to the back lines


Hmm, well you're not telling us much like the make model year? Anyway to take a stab at it you may have a bad master brake cylinder or even a bad proportioning valve. Check to see if you have pressure at the proportioning valve. If so then the master cylinder is fine and your proportioning valve needs to be replaced. But if there isn't any pressure there then of course it's your master cylinder. But again since I don't know anything about your vehicle I'm assuming it's an older one with a standard type of braking system. As you get newer then you get into much more things that could go wrong.

Nov 22, 2012 | Cars & Trucks

1 Answer

1975 gm pick-up need to bleed the proportional valve


All bleeding is done at each caliper and wheel cylinder. The proportioning valve has no bleeder. The proportioning valve makes the front brakes engage before the rears do to prevent the rear brakes from causing a sideways skid.

Jul 21, 2011 | Chevrolet G10 Cars & Trucks

1 Answer

Villager GE 95 liquid escape in a brake system


It is a brake load sensoing valve that applies more pressure to the rear brakes as you load the vehicle. It is $375 from tascafordparts.com. Get one from the junk yard or just bypass it.

usually just the lines are leaking and can be replaced.
Valve, Brake Load Sensor Proportioning The Villager has a brake load sensor proportioning valve (2B547) that is mounted on the vehicle frame and connected to the rear axle housing (4010) . When the vehicle is unloaded, the brake load sensor proportioning valve closes and partially reduces hydraulic pressure to the rear wheel cylinders (2261) . As the vehicle is loaded, the weight presses down the back end of the vehicle on the rear springs (5560) . This activates the brake load sensor proportioning valve which opens and supplies more hydraulic pressure to the rear wheel cylinders . When the vehicle is fully loaded, the brake load sensor proportioning valve is fully open and provides full hydraulic pressure to the rear wheel cylinders .
-------------------------------------

fb0a5fa.gif

Jun 26, 2010 | 1995 Mercury Villager

1 Answer

Where is the proportioning valve on a 2000 chev blazer and can it be reset


Proportioning valve for the brakes? rear brakes? rear brakes are located on the rear end, for all brakes(front to rear proportion) is usually part of or under the master cylinder, and if either are bad then you need a new one, there is no resetting them

Feb 23, 2010 | Chevrolet Nova Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Infiniti Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14223 Answers

Are you an Infiniti Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...