Question about 2003 Mazda 6

Open Question

Removal of 120A main fuse. I have a 2003 mazda 6 sport. Need to change the main fuse. I have the wires off. Can't figure out how to get to the horizontal bolts holding it in.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: Blown main fuse on 2003 mazda protege 5.

There are two bolts on the side of the fuse itself. Under the fuse box on each side. Unbolt those and it will come out.

Posted on Dec 23, 2008

Ad
rps evo
  • 3 Answers

SOURCE: mazda 323 1996 Alternator Wireing.

Hi,i am from greece and i want bigger front brakes for to my mazda 323c 1.3 cc 16v, mod.95. Can i use from another mazda model and which is that?

Posted on Feb 21, 2009

  • 205 Answers

SOURCE: fuel pump removal in a 2005 mazda 6 4 cylinder

you have to use a screw driver and hammer to tap it to the left until the tabs line up with the notches on the ring.

Posted on May 21, 2009

  • 67 Answers

SOURCE: changing a wheel bearing, 2003 mazda 6

to change that, using a hydraulic press is highly recommended. if you are DIY experienced, this trick works as well:

take a pice of a stable metal pipe, 10-20 cm long. and in diameter just a tick smaller than gross bearing size. take a very heavy tool and use the pipe to beat out the old bearing. dont be shy, needs a lot of power.

do not use this method to insert the new bearing. use a pice of wood instead (must sit stable on the outer bearing ring!!), lubircate a bit and beat carfully and very straigt in fractions of a mm. this is the difficult part and here the bearing may brake if you are too rough.

Not really recommend, but working when used with brain and care.

Posted on May 29, 2009

hardinfarms
  • 144 Answers

SOURCE: 2003 mazda 6 3.0 need the main bearing torque specs

I'm sending you the torque specifications for your main bearings and also your head bolts. I also sent you main bearing and cylinder head tightening sequence. I hope this will be useful2c713bf.giffce6623.gif
Main Bearings Torque specs. 40-43 Ft. Lbs.
Cylinder Head Torque specs. 56-60 Ft. Lbs.

Posted on Oct 05, 2009

Testimonial: "thank you so much! couldnt find this information anywhere, even called the local mazda dealers!"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Car will not start


Check the battery of ur car and check ur starter plug

Jun 11, 2008 | 2004 Mazda RX-8

1 Answer

How do I replace the 120A main fuse in my 2005 Mazda Atenza?


disconnect the battery , the 120 amp fuse is a complete unit that is housed in a plastic case, that needs to be pulled out , it will be very tight and may break but keep pulling

Jul 11, 2014 | Cars & Trucks

1 Answer

Mazda6 2003


There is probably a bolt that runs through the blades of the fuse. You have to remove the bolt before you can pull the fuse.

Mar 02, 2014 | 2003 Ford Focus

1 Answer

BATTERY short circuit


I do not really understand the question. Did you jump start the car backwards?

When that happens, usually it blows the "main fuse." It is usually white or black ( 80 - 120A). To replace it on most Mazda's you have to partially disassemble the under hood fuse box to remove the 2 bolts holding it into the car, but this is just pure speculation

Jan 13, 2014 | Mazda MAZDA3 Cars & Trucks

1 Answer

2003 mazda 6 3.0 need the main bearing torque specs


I'm sending you the torque specifications for your main bearings and also your head bolts. I also sent you main bearing and cylinder head tightening sequence. I hope this will be useful2c713bf.giffce6623.gif
Main Bearings Torque specs. 40-43 Ft. Lbs.
Cylinder Head Torque specs. 56-60 Ft. Lbs.

Oct 05, 2009 | 2003 Mazda Mazda6

1 Answer

Where is the fuse box that is supposed to be under the stearing wheel


Mazda 323/MX-3/626/MX-6/Millenia/Protégé 1990-1998 Repair Guide

1994 Mazda MX-6 2.0L MFI DOHC 4cyl

Circuit Braker
A bimetal circuit breaker is located in the joint box, which is just above the interior fuse panel. This circuit breaker protects the rear window defrost circuit and is the plug-in type.

Fuses
The main fuse block is located inside the left side of the engine compartment near the battery. There is also an interior fuse panel located just above the left side kick panel.

Fuses Replacement

CAUTION Never replace a blown fuse with one of a higher rating. Severe damage to the vehicle, electrical harness and components, as well as personal injury or even death could occur.
Main Fuse Block
(see Figure 1)
  1. Disconnect the negative battery cable.
019fba1.jpg

Fig. 1: Remove the fuse box cover, located in the engine compartment, to access the main fuses for the vehicle
  1. Unhook the lock tab from the main fuse block cover and open the cover.
  2. Pull the fuse from the main fuse holder.
  3. Installation is the reverse of the removal procedure.
Interior Fuse Panel
The interior fuses simply unplug from the fuse panel. Use the fuse puller tool provided with your car to remove fuses from the panel. The tool is located on the back of the interior fuse panel cover.


Relay
The main relay box is located on the upper left-hand side of the firewall (bulkhead). There is also a relay box mounted inside the vehicle under the left side of the instrument panel.

Relay Replacement
  1. Disconnect the negative battery cable.
  2. If replacing a relay at the main relay box, disconnect the electrical connector and slide the relay from its mounting bracket.
  3. If replacing a relay at the interior relay box, simply unplug the relay.
  4. Installation is the reverse of the removal procedure.

410a634.gif

Fig. 1: Typical fuse box and panel locations and configurations


I hope help you with this (remember rated this help) Good luck.

Sep 28, 2009 | 1994 Mazda MX-6

1 Answer

My Mazda 6 sport has xenon discharge headlights. One of them keeps going off while driving. I can't find any loose connections, and the Mazda dealer couldn't reproduce the problem. Any advice?


I had the same Problem on My Mazda 6 Sport. If you turn the lights off then back on the light comes back on.The main dealer eventually changed the headlight, after being instructed by Mazda that there was a common fault within the sealed unit.
My advise is to take it back to the dealer, and tell them mazda have nbeen changing them under warranty.

Aug 13, 2008 | Mazda MAZDA6 Cars & Trucks

Not finding what you are looking for?
2003 Mazda 6 Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8557 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...