Question about Cars & Trucks

Open Question

To change the door hanging are the brackets universal

Posted by on


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

Changed brakes rotors and clibers Twice, they were run down to bare steel on 50 Mi. The car runs at 7000 RPM's on and off while driving under 30 MPH. what is is ?

sounds like your brakes are hanging up would check caliper slides and hi-pressure rubber lines also check caliper mounting bracket and make sure pads move freely before mounting caliper over pads pads should move freely on mounting bracket

May 16, 2016 | 2003 Hyundai Accent

1 Answer

Low Hanging Muffler

get a hanger from the store

Jul 11, 2013 | 1997 Pontiac Grand Am

1 Answer

Parts breakdown for 1993 k1500 chevy

Go to the GM dealer and have them bring up the parts diagrams for the section of the truck where the part is attached and then ask for a description of what it is.

Aug 23, 2012 | Cars & Trucks

1 Answer

My door will not shut the peace were the door connects to the metal u bracket is pushed in and cant figure out how to get it back to were it was like the other doors so i can close it

Your door like your hood has a latch mechanism which locks around the "u bracket" if the latch is in the closed position try some wd40 or other penetrating oil to help free it up and try working the inner and outer handle to release it. There is a small metal linkage form the outer door handle and a much longer one from the inner handle which may have come loose if it does not work either way. you would need to remove the door panel to access it and you can get a universal replacement if needed at your local parts store

Apr 22, 2011 | 2001 Pontiac Grand Am SE

1 Answer

How to change brake pads on a 2005 jeep liberty

remove wheel useing 3/4 or 19mm soc 13mm rachet wrench or soc will remove the calipher use a small bunge or a piece of wire to hang calipher up do not let calipher hang by can now change pads, if you want to change rotor also you need a 21mm soc to remove bracket that holds pads. reverse procedure and you are done.

Jul 16, 2010 | 2005 Jeep Liberty

1 Answer

How do i change the rear shocks on toyota previa

Some SUVs the rear shocks bolt to the floor panel and some bolt to a hanging bracket from the bottom. The bottom of the shock always uses the rear axle bracket. Make sure the car is jacked up safe with jack stands and level surface

Oct 14, 2009 | 1993 Toyota Previa

1 Answer

Driver side door will not open with or without key. The car has power locks.Is there a diogram with how to around? The door willopen from inside, also you can't pull the lock up on the door, like it is...

What happens on these power door locks is the solenoid comes loose or breaks off the bracket and it hangs rom the linkage. You've got to remove the door panel and disconnect the lock solenoid from the linkage.

Oct 08, 2009 | 1992 Dodge Dynasty

1 Answer

2002 Mercury Marquis Heat only comes out vents

There could be a thermal switch for blower speeds and temp. Since you needed to replace the battery, the thermal switch could have run down the battery. When you restored a dead battery with a fully charged battery a resistor blew. There is a cover underneath the glove box that can be removed and the glovebox lid can easily be unclipped to hang out of the way. Just look at the sides of the glovebox and you will see brackets which can be pinched to let the lid hang down. Unplug the switch and look for melted parts.

Feb 02, 2009 | 2002 Mercury Grand Marquis

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides