Question about Cars & Trucks

Open Question

How to do the epley maneuver - Cars & Trucks

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to maneuver the center console out of a 2008 Chrysler Sebring to replace interlock spring?


Take a close look at the shift interlock cable, can repair without removing the console entirely. Might want to contact your local dealer see if there is any open recalls.

Oct 17, 2015 | 2008 Chrysler Sebring

1 Answer

Where is the power steering pump located?


ELECTRIC POWER STEERING (EPS)
The TSX uses Electric Power Steering (EPS) which regulates steering via a computer-actuated electric motor. With the computer-controlled system, advanced algorithms built into the operating software allow for continuous fine-tuning of the steering assist forces so that minimal force is required at low speeds- such as when parking or maneuvering. Conversely, progressively higher steering effort is generated at higher speeds (such as when driving on the freeway) to deliver a sport-minded driving experience.
The EPS system found in the TSX is an evolution of an earlier EPS system found on the Acura NSX supercar. Its key features and advantages include:
  • The EPS system reduces the steering effort at low speeds, improving agility and ease of effort when parking or maneuvering in tight areas
  • Rigidity of the steering mount is higher, which allows a more precise and "connected" feel during high-speed maneuvers (such as during lane changes or when on winding mountain roads)
  • The EPS steering assist incorporates computer algorithms based on vehicle speed rather than engine speed, allowing TSX engineers the flexibility of tailoring the steering feel to match actual driving conditions- especially high-speed driving. The EPS steering algorithms incorporate steering assist changes for every 0.6 mph.
  • The EPS system is different (and uniquely tuned) for each of the TSX models: 2.4L I-4 sedan, 3.5L V-6 sedan, and the new Sport Wagon.
  • EPS employs a sporty, 13.5:1 steering ratio which further improves performance driving agility
  • In its evolution from the original NSX system, the TSX's EPS system uses a significantly more powerful electric motor teamed with a far more sophisticated microprocessor
  • By eliminating the conventional power steering pump assembly, EPS uses less engine power which improves acceleration and fuel efficiency
it is an electric pump without a pulley or belt or fluid apparently

Aug 09, 2014 | 2011 Acura TSX

1 Answer

2005 GMC ENVOY 4.2L VIBRATION PROBLEM AT IDLE AND START UP OR ANY TIME NO ACCELERATING


Hello! This is a known problem that is addressed by the following Technical Service Bulletin...Guru...saailer

Subject:Steering System Moan, Groan, Shudder and/or Vibration Type Noise During Low Speed Turning Maneuvers (Replace Steering Gear) #04-02-32-007A - (12/01/2004) Models:2004-2005 Buick Rainier
2003-2005 Chevrolet TrailBlazer, TrailBlazer EXT
2003-2005 GMC Envoy, Envoy XL
2004-2005 GMC Envoy XUV
2003-2004 Oldsmobile Bravada
Short Wheelbase Utilities Built Prior to VIN Breakpoint 52123375
Long Wheelbase Utilities Built Prior to VIN Breakpoint 56137280
This bulletin is being revised to remove the 2002 model year and add the long wheelbase utilities. Please discard Corporate Bulletin Number 04-02-32-007 (Section 02 -- Steering).

ConditionSome customers may comment on a moan, groan, shudder and/or vibration noise while making low speed turning maneuvers. Customers usually notice this condition in parking lot turning maneuvers.
Correction
  1. Diagnose the power steering concern. Refer to Symptoms - Power Steering System (SI Document ID #670351).
  2. Replace the steering gear with a newly designed steering gear. See the parts information below. Refer to Power Steering Gear Replacement (SI Document ID #742314).
Parts Information

Part Number

Description

Qty
88965356
Gear Kit, Steering
(Short Wheelbase Utilities)
1
88967181
Gear Kit, Steering
(Long Wheelbase Utilities)
1
Warranty InformationFor vehicles repaired under warranty, use:

Labor Operation

Description

Labor Time
E9740
Gear Assembly, Power Steering - Replace
Use published labor operation time
E2000
Toe, Front - Adjust

May 03, 2012 | GMC Envoy XL Cars & Trucks

1 Answer

The steering wheel is so hard to maneuver


Check the power steering pump fluid level, if it is good, you may have a problem with the rack or a defective pressure hose.

May 15, 2010 | 2004 Chevrolet TrailBlazer

1 Answer

How do you get to the spark plugs on the back of the block on a 2005 Mercury Sable w/ a 3.0L V6 engine?


you have to reach around from up top, no special tricks. just a little maneuvering and some skinned knuckles.

Nov 17, 2009 | 2005 Mercury Sable

1 Answer

Changing spark plugs on 97 2.0 jetta gl does the intake manifold have to be removed


no. you can get on the plug with an extension and a bit of maneuvering.

Nov 11, 2009 | 1997 Volkswagen Jetta

1 Answer

Need to replace starter


Removal & Installation To Remove:
  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Disconnect battery negative remote cable from remote ground post.
  3. Raise and safely support the vehicle
Starter Motor

098a02a.gif
    1. Remove or disconnect the following:
    2. Three bolts attaching starter to engine
    • Positive battery cable from starter
    • Starter assembly from transmission housing
    1. Position jack stand beneath engine and slightly lift to relieve pressure from left engine mount.
    2. Remove three left engine mount bolts from engine block.
    3. Jack engine up slightly to give more room to maneuver starter assembly.
    4. Slide rear of starter motor out between catalytic converter and engine mount.
    1. Remove or disconnect the following:
    2. Posi-lock starter solenoid connector.
    • Starter from vehicle.
    To Install:
    1. Install or connect the following:
      • Positive battery cable to starter
      • Posi-lock starter solenoid connector
    2. Jack engine up slightly to give more room to maneuver starter assembly.
    3. Install or connect the following:
      • Starter
        1. Torque to 40 ft. lbs. (54 Nm)
      • Three left engine mount mounting bolts to engine block
    4. Lower vehicle.
    5. Connect the battery negative cable.
  • May 05, 2009 | 1998 Chrysler Concorde

    3 Answers

    How do you change an alternator on a 3000gt


    it may be under the AC compressor. you will have to take off the front right tire and loosen all engine mounts. using an engine hoist, drop engine to allow room for maneuvering. disengage negative battery cable from battery, thats the black wire.

    Sep 09, 2008 | 1993 Mitsubishi 3000GT

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    20 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Cars & Trucks Experts

    yadayada
    yadayada

    Level 3 Expert

    76691 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22219 Answers

    Randy Ohler

    Level 3 Expert

    14585 Answers

    Are you a Car and Truck Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...