Question about 1999 Chrysler Cirrus

1 Answer

How do you remove the Harmonic balancer on a 1999 chrysler cirris

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 501 Answers

Have you done a search on YouTube? Lots of how to videos there.

Posted on Dec 14, 2016

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

Lost key for 1999 Chrysler Cirris.need to replace ignition lock cylinder


take center of steering wheel off,access the star screw through a hole in the wheel to remove mechanism

Jul 23, 2015 | Chrysler Cars & Trucks

2 Answers

I have a 1999 Chrysler Cirrus. The serpentine belt came off that goes to the alternator and the air conditioner unit, I was told by a mechanic that the dampner pulley is bad. Some autopart sites have a...


Hi, assuming you have the 2.5 liter engine, your damper is integral to the pulley assembly as shown in the second figure below, so there is only one part involved. You can see an example of the part here: http://www.autozone.com/autozone/parts/Dorman-Harmonic-Balancer/1999-Chrysler-Cirrus/_/N-jddk1Z93y2h?counter=0&itemIdentifier=917091_0_0_
If you look carefully at the pic below, you can see the rubber torus inside the pulley. The rubber is what fails and causes the pulley to wobble. You may need to borrow a puller to get the pulley off.

2.5L Engine
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Disconnect battery negative cable from remote negative terminal on shock tower and properly isolate to prevent accidental reconnection.
  3. Remove or disconnect the following:

    Belt splash shield Accessory drive belts. Refer to Belts. Crankshaft center bolt and remove crankshaft damper.

    jturcotte_2368.gif

    Fig. Splash shield removal-2.5L engine

    jturcotte_2369.gif

    Fig. Crank damper and bolt- 2.5L engine

To install:
  1. Clean crankshaft snout and crankshaft damper bore.
  2. Install or connect the following:

    Crankshaft damper. Crankshaft bolt and torque to 143 ft. lbs. (182 Nm) Accessory drive belts. Refer to Belts. Belt splash shield

Oct 05, 2011 | 1999 Chrysler Cirrus

1 Answer

What does the crank sensor look like for a 1999 chrysler sebring lxi?


just a piece of plastic its the only sensor it is located under harmonic balancer pully on most vehicles some are just right outside the harmonic balancer pully


if it helps please leave a good review thumbs up

May 08, 2011 | 1999 Chrysler Sebring

1 Answer

Does the harmonic balancer need to be removed to replace the water pump?


Hello mue037,

Yes, the harmonic balance pulley must be removed as well as the timing belt. The water pump is driven by the timing belt.

Regards,
netvan

Feb 27, 2011 | 1999 Chrysler 300M

1 Answer

How to remove a 1996 Chrysler Cirrus harmonic balancer


you need a harmonic balance puller without that its not worth attempting

Jan 01, 2011 | Chrysler Cirrus Cars & Trucks

2 Answers

I have a 1999 300m, the harmonic balancer pulley is wobbling, Should I replace, and also will that cause a metal sound??


Most definitley replaceas it evens out crankshft vibrations. May cause metallic sound replace ASAP.

Mar 10, 2010 | 1999 Chrysler 300M

1 Answer

Where do i find the cam shaft and knock sensors for a 1999 chrysler 300m?


remove the intake manifold ,remove radiator ,remove radiator intake and outake housing, remove fan ,remove all belts: power steering, alternator and if you have a/c, remove harmonic balancer ,remove timing belt covers, remove timing belt remove intake housinng once you have remove all the above, your freaken engine will look naked, you can see the location of the knock sensor is locate in the engine valley

Feb 09, 2010 | 1999 Chrysler 300M

1 Answer

How to replace harmonic balancer chrysler concorde 2004 3.5 engine


Remove the cooling fans assy, remove the center bolt from the balancer, then using the special balancer, remove the balancer. Autozone had this tool you could borrow.

Jan 23, 2010 | 2004 Chrysler Concorde

1 Answer

I cant get the harmonic balancer off my 1999 chrysler 300m. I have broken 2 3 prong pullers trying to get it off. How do I get it off??? Help!!


there is a special chrysler puller needed for that particular balancer...its available through mac tools and snap on...you may be find it through canadian tire or napa even...try that...

Nov 07, 2009 | 1999 Chrysler 300M

Not finding what you are looking for?
1999 Chrysler Cirrus Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...