Question about 2006 Mitsubishi Galant

1 Answer

What is the pin voltage for a 06galant 2.4 camshaft sensor?

Po340 changed sensor. Got same code again. Can see rpm on my scanner.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Welcome Back:

    Visited the website for 2 consecutive days.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 12 Answers

Most vehicle sensors are 5volt

Posted on Dec 15, 2016

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Code p0340, p0462 on subaru outback 2001


Po340 is a cam shaft sensor and po462 is low voltage on your fuel guage. So i assume you are haveing fuel level issues. If you can turn wrenches you can do these repairs yourself. Just do a google search and you can get some youtube videos of sensor replacement and location. Have fun.

Aug 29, 2014 | 2001 Subaru Outback

1 Answer

What is code PO340 in a van ford windstar 2000


P0340 Ford - Camshaft Position Sensor Circuit Bank 1 Sensor

Read more: http://engine-codes.com/p0340_ford.html#ixzz393ZCFfRt
Site gives possible causes and procedure to replace sensor if needed.

Jul 30, 2014 | Ford Windstar Cars & Trucks

1 Answer

I recently bought a 2005 Dodge Neon, the oil light was coming on so I reported to dealer who replaced oil sensor switch, now the check engine light is on so I bought a pocket scanner and it comes up with...


Trouble Code: P0340

No Camshaft Position Sensor Circuit Failure

Possible Causes:


CMP Sensor connector is damaged, open or it is shorted.CMP Sensor signal circuit is open or shorted to ground or to battery voltage or 5v supply circuit.CMP Sensor 5v supply circuit is open or shorted to ground or to battery voltage.CMP Sensor ground circuit is open.CMP Sensor is damaged or has failed.CKP Sensor is damaged or has failed.PCM has failed.I would make a copy of this and tell him that the camshaft needs to be replace or what ever is causing problem,they probaly know.

Jan 13, 2013 | 2005 Dodge Neon

1 Answer

2003 Hyundai Santa Fe Still Will Not Start PO320 PO340


code p 0320 refers to crank shaft position sensor (CKP)/engine speed (RPM ) sensor---circuit malfunction====causes ---wiring---CKP/RPM sensor ---ECM
code p 0340 refers to camshaft position sensor (CMP) sensor A bank 1---circuit malfunction===causes wiring---CMP sensor ---ECM
following engine work , it is always best to check that all of the harness connections were assemble properly
check for broken wires during the work

Apr 29, 2017 | 2003 Hyundai Santa Fe

1 Answer

HELLO, I HAVE TROUBLE CODES PO330,PO340, ON MY OBD2 READER WITH THE MAINT LIGHT ON IN 96 BMW Z3 ROADSTER 4CYL., PO330 IS KNOCK SENOR, PO340 IS CAMSHAFT POSITION SENOR, I WANT TO KNOW HOW TO FIX THEM BOTH....


The Cam Position Sensor is a common item to fail. However, the cam positioning mechanism can fail too giving that code.

There are two sensors and the Exhaust Cam Sensor is most common to fail. I always replace both.
Te CKP's are on the top front of the engine next to the cylindrical operation solenoids.

Knock sensors fail too and need checked or correct feedback to ECU with a scanner.
Find a shop near you at http://www.iatn.net/shopfinder/

These engines require regular oil changes with quality synthetic oils and OE filter....not a FRAM or WIX !

Buy only BMW sensors ...aftermarket have high failure rate.

Jan 12, 2011 | 1996 BMW Z3 Roadster

3 Answers

P0340 code. I Changed cam sensor and checked wiring. what else could be wrong? Jeep cherokee, 6 cil


A code P0340 could mean one or more of the following has happened:

•a wire or connector in the circuit could be grounded/shorted/broken
•the camshaft position sensor may have failed
•the PCM may have failed
•there exists an open circuit
•the crankshaft position sensor may have failed

With a P0340 OBD-II trouble code, diagnosis can be tricky at times. Here are some things to try:

•Visually inspect all the wiring and connectors in the circuit
•Check for continuity in the circuit wiring
•Check the operation (voltage) of the camshaft position sensor
•Replace the camshaft position sensor as required
•Check the crankshaft position circuit as well
•Replace circuit wiring and/or connectors as required
•Diagnose/replace the PCM as required

Feb 20, 2010 | 2000 Jeep Grand Cherokee

1 Answer

My car is not getting any spark from the coil


T COULD BE YOUR CAMSHAFT SENSOR OR CRANKSHAFT SENSOR. SOMETIMESTHE TIMING CHAIN JUMPS A TOOTH AND CAUSES THIS TO HAPPEN ASWELL.

1. At the coils, check for battery voltage at the Red wires while cranking, the Black wires should be less than 0.05 volts while cranking. Pin 3 at the coils (each wire color at the #3 pin are different) using a scope watch for a 3 - 4 volt pulse signal while cranking. Red wire - battery voltage, Black wire is a ground and the White wire is the signal circuit

2. If there is no pulse signal to the power transistors, using a scanner check the POS counts (Position) should be 179 - 181 while cranking. If inconsistent, check the signal plate (flywheel/flex plate) for damaged teeth. If there is an RPM signal and the POS counts are correct, this crankshaft sensor is good.

3. On the front of the engine, mounted on the oil pan is the crankshaft sensor (REF) reference. Check the AC voltage while cranking, should be a clean sine wave that indicates the Top Dead Center (TDC) position of each piston. White and Black wires in a 2 pin connector

4. Check the Camshaft (phase) sensor AC voltage output. This sensor should also be a clean sine wave. This sensor detects cylinder number. This sensor is located in the front cover facing the cam gear. White and Black wires in a 2 pin connector.

Nov 07, 2009 | 1995 Nissan Maxima

2 Answers

Po340 code will not start occasionally then engine light comes on and thats the code that shows


tht is a camshaft sensor code. you probablyhave a sensor just starting to go bad and when it does the truck won't start no more. if you want to look atthe wire haness going to the cam sensor and if it looks good thaan swap the cam sensor.

also if you give the size engine you have i can give you a test to do with a meter to check it. but most of the time if thevehicle is running you can't tell. it has to be broke to tet it. but to re assure you i istall alot of cam sensor nd also crank sensor. so it is a very common problem...goodluckand ask any more question you have.

Sep 25, 2009 | 2001 Jeep Grand Cherokee

2 Answers

For what sensor is the code po340 on a dodge neon 04 and how i change.


Hi,
This indicates that a problem was detected in the camshaft position sensor circuit. Since it says circuit, that means the problem could lie in any part of the circuit - the sensor itself, the wiring, or the PCM. Don't just replace the CPS (camshaft position sensor) and think that will definitely fix it.

With a P0340 OBD-II trouble code, diagnosis can be tricky at times. Here are some things to try:

  • Visually inspect all the wiring and connectors in the circuit
  • Check for continuity in the circuit wiring
  • Check the operation (voltage) of the camshaft position sensor
  • Replace the camshaft position sensor as required
  • Check the crankshaft position circuit as well
  • Replace circuit wiring and/or connectors as required
  • Diagnose/replace the PCM as required
Thanks.

Jun 28, 2009 | 2004 Dodge Neon

1 Answer

1995 Windstar OBD II showing codes PO340, PO171, and PO174


Hello;
With those codes, the first place I would check is the fuel pressure. Also check the fuel filter and replace it if you haven't already. Then clear codes and recheck. Even if your fuel pressure is with in range it still may not push enough fuel to operate your vehicle.

Jan 15, 2009 | 1995 Ford Windstar

Not finding what you are looking for?
2006 Mitsubishi Galant Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...