Question about Nissan Maxima

Open Question

I have a 2005 nissan maxima car starts but wont rev over 2000 rpm if i try to hold at 2000 rpms the rpms drop and engine stalls replaced fuel pump no change

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 11 Answers

SOURCE: fuel problem

I had the same problem with my 99 Subaru Forester and it was caused by oil leaking and getting into the spark plugs. We only needed to remove & clean one of the plugs and then we were running smoothly again. Very well could not be what your problem is but it's worth a shot mentioning.

Posted on Feb 28, 2009

  • 1 Answer

SOURCE: car dies when slowing down or stopping

Disconnect the air hose going to the Idle Air contorl Valve and plug the line with a small screw.
if the problem of the idle goes away and the car runs smooth and doesn't stall at stops, it's the air control valve housing sensor, it's basicall the whole unit thats no good. If it still stalls, clean the throttle body housing and all parts in where the air gets sucked in, put a rag underneath to keep the dirt from dripping down, start the car with somebody inside the car reving up the engine to 2000rpm's to 2500rpm's, then spray in to the throttle with burst of throttle cleaner and you will see the gunk keep coming out, you may have to change your spark plugs after this is done also.

Good Luck BigWillie

Posted on May 03, 2009

  • 7 Answers

SOURCE: i have a 2000 nissan maxima and the problem that i

Idle air control valves short out all the time on these models. You can ohm the motor to check it, but the down side to a shorted iac valve is that it shorts out the ecm if not repaired quickly. when the valve shorts, 12 volts is supplied directly to the ecm and burns the circuit board. The other option is the air flow meter, this is also a very common problem but typically a p0171/p0174 would be stored in self diag.

Posted on Jun 22, 2009

  • 1 Answer

SOURCE: my nissan maxima stalls

Every answer here is wrong. This has been driving people nuts for 15 years. The problem is the engine wiring harness which has a bend going past the right strut tower, Nissan had a service bulletin on this in September of 1999, Google it, it's in pdf.

Posted on Aug 23, 2009

  • 289 Answers

SOURCE: 2003 Chevy Cavalier 2.2L - RPMs Surge & Drop Out - Stalls In Idle

it sounds like its drawing air into the inlet mannifold

Posted on Apr 17, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 03 Nissan Altima wont get over 2500 rpms


first check your fuel system, replace fuel filter, also check your fuel pressure regulator on your fuel rail it may be leaking internally if ok check your fuel pump operation. if your fuel system is ok then check for a restricted catalytic converter its a common fault I encounter with them. if that to checks out ok then have the ecm scanned by a shop or the dealer could be a faulty engine speed sensor or crank or cam sensor

Jan 18, 2015 | 2003 Nissan Altima

1 Answer

My 2000 Nissan maxima wont rev above 2RMP.


Have you inspected the catalytic converter for blockage? The other issue could be fuel pressure...the fuel regulator could be defective. Hope this helps.

Jun 12, 2012 | 2000 Nissan Maxima

1 Answer

I have a 95 Maxima that occasionally stalls when I come to a stop. The check engine light was on so I hooked it up to an OD2 sensor and it gave the following 7 codes: P 1320 - Distributor Signal...


Trying to clean the MAP sensor will damage it. Install a New Air filter and The Fuel filter, then replace the MAP sensor. Do not touch, or spray(compressed air or solvent) on the element when installing it. Have all of the OBD II Stored codes Deleted. Add a can of B&G 44K fuel additive to a full tank of fuel. The B&G is the best on the market, do not substitute. It is only available Through dealerships (Toyota). It will condition fuel pump and injectors. The ECU in your car is very dependable and rarely needs replacing. Always Replace cheapest parts first. Test drive the car and Then recheck The OBD II for new faults. The dimming of your lights before shut down was due to RPM of the engine dropping below 750 RPMs. Alternator will not produce voltage below 750 Rpms. 30 Amps at 14 Volts is required to run the engine.

Mar 03, 2017 | 1995 Nissan Maxima

1 Answer

Stalls when excellerating


i would do a few things here, simply spend $8 on some injector cleaner to break down carbon deposits, then try replacing the fuel filter, lastly, get the timing checked, plug gaps {new plugs} clean oxygen sensor in exhaust then lastly get the fuel pump pressure checked at a mechanics, all in that order untill it works, Good luck

Nov 20, 2009 | 1986 Nissan Maxima

2 Answers

Nissan Maxima 1997 250,000 kms


could be the oxygen sensor manybe, or fuel pump

Sep 03, 2009 | 1997 Nissan Maxima

4 Answers

I have a 2000 nissan maxima and the problem that i


Idle air control valves short out all the time on these models. You can ohm the motor to check it, but the down side to a shorted iac valve is that it shorts out the ecm if not repaired quickly. when the valve shorts, 12 volts is supplied directly to the ecm and burns the circuit board. The other option is the air flow meter, this is also a very common problem but typically a p0171/p0174 would be stored in self diag.

Jun 14, 2009 | 2000 Nissan Maxima

1 Answer

1995 Nissan Maxima


Since RPM meter is also important so that you can control the engine from overspeed. It is also important to repair the thing your rpm cable maybe worn out already. If it is an electronic rpm meter cold Solder in electronic lead might be the cause.

Jun 01, 2009 | 1995 Nissan Maxima

1 Answer

Car runs fine at idle but wants to surge


there is a fuel pump inside the tank that is bad replace it

Jan 01, 2009 | 1988 Nissan 300ZX

4 Answers

Car dies when slowing down or stopping


Disconnect the air hose going to the Idle Air contorl Valve and plug the line with a small screw.
if the problem of the idle goes away and the car runs smooth and doesn't stall at stops, it's the air control valve housing sensor, it's basicall the whole unit thats no good. If it still stalls, clean the throttle body housing and all parts in where the air gets sucked in, put a rag underneath to keep the dirt from dripping down, start the car with somebody inside the car reving up the engine to 2000rpm's to 2500rpm's, then spray in to the throttle with burst of throttle cleaner and you will see the gunk keep coming out, you may have to change your spark plugs after this is done also.

Good Luck BigWillie

May 29, 2008 | 2000 Nissan Maxima

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...