Question about Ford Transit

Open Question

Heater switch 96 transit truck .need help with wiring for a newer switch.

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Will a 2007 mondeo 2L dtci engine fit in a 2007 transit 2.2 tdci if I use the mondeo ecu ?


It will, but you need all the computers out of the transit. ECU,BCM,Radio,Security, ignition switch and key, then you need to make sure the wiring is the same...

Oct 23, 2015 | Cars & Trucks

2 Answers

Ford transit forum


Was the old switch tested & bad?

Need a wiring diagram to work on windows

Can't work on any vehicle problem, until you
have the required info & study how the system
works, first.

Have to test things to find a problem, before
you can correct it

Jul 17, 2014 | 2010 Ford Transit Connect

1 Answer

Looking for a wiring diagram for my 96 ram 2500 ignition switch... Suggestions?


Shop manuals used to contain full wiring diagrams, but newer ones often just say the diagrams are so complicated they are not included. In my experience, dealer parts departments will often provide copies of portions of wiring diagrams free, particularly if you ask nicely. Online forums for your specific vehicle often will provide this as well. Is there some specific issue we might help with?

Apr 13, 2014 | 2000 Dodge Caravan

1 Answer

96 ford e350air conditioner problem


Looks like you checked all the things that need to be checked except "one." Sounds stupid, but did you check your temp switch on you dash to make sure it is the air conditioner you want to run instead of the heater? Sometimes, many forget this one simple check and can't figure out why the air conditioner won't engage.

Sep 10, 2012 | Cars & Trucks

1 Answer

Might Max 210,000 Mile check engine light is on. Code says 42 (fuel pump) No problems with truck starting or running. Reset with switch and reset by disconnecting neg Batt. Light comes back on.


Not sure what year you have but if its newer than a 96 then the code is for an 02 sensor. Bank1 sensor 3

It will be the sensor after the catalytic converter. It needs to be replaced. The code is a heater code and always it points to a bad 02 sensor.

Jan 04, 2010 | Mitsubishi Mighty Max Cars & Trucks

1 Answer

I have a 96 deville. have replaced the blower


INADVERT Relay next to the engine compartment fuse block on drivers side i need one to

Aug 13, 2009 | 1996 Cadillac DeVille

1 Answer

Will the blower power modules from a 1997,1998,1999,work on a 1996 chrysler.


Don't see a LHS for 1998, just compared 96 and 97, 2 different parts although same engine. They must have modified the heater/ac system in 98. From what I can tell, the 96 has a bracket attached to the motor whereas the 97 doesn't . If you were to remove the old blower motor and bring it to the junkyard and check it against the 97 or newer blower motors, it's possible that its just a matter of retrofitting the bracket off your broken motor to the newer model. Hope this helps and Best of Luck to you!

May 10, 2009 | 1996 Chrysler LHS

1 Answer

96 4Runner - Help with Dash lights


You need to replace the bulbs behind the heater control. The bulbs have rather large filaments, and hitting the control sometimes makes the filaments "weld themselves" back together for a short time. I would not suspect a short or a loose wire.

Nov 03, 2008 | 1996 Toyota 4Runner

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...