Question about Cars & Trucks

Open Question

Order new blowers - Cars & Trucks

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Blower motor fan speed control switch


It is probably the blower control module, not your temperature switch - I would try replacing that.

Jun 11, 2017 | Pontiac Aztek Cars & Trucks

1 Answer

Need to replace blower motor


Instructions
    • Remove the passenger side kick panel using a Phillips head screwdriver. Pull the rug back from under the blower motor to allow enough room to drop the blower motor without the rug interfering.
    • 2Disconnect the electrical plug from the blower motor. Pull the rubber vent hose out of the blower motor.
    • 3. Remove all the Phillips head screws securing the blower motor to the housing. Drop the blower motor straight down.
    • 4. Install the new motor in reverse order of removal.

Dec 19, 2012 | 2003 Buick LeSabre

1 Answer

Air works but it dosent blow anymore I was thinking the blower motor or the switch


Hello: It could be the blower motor but first check the wires (6) going to the blower motor from the module (under the passenger side dash close to the blower motor and check the wires going from the (2) module to the blower motor. The module itself may be burnt where the 6 wire connector plugs in. If so the module will have to be replaced. GM sells a harness so you can replace the burnt connector, just connect the new harness one wire at a time. Make sure you orientate the new connector like the old so you get the wires in the correct order.

Jun 15, 2011 | 1999 Chevrolet Silverado 1500

1 Answer

Wher is the blower moter located at to a 2002 cadillac deville how do i replace the heater blower motor


The blower motor is located under the glove box. It is a very difficult procedure to replace. The blower motor has six 7/32 size screws, two of which are hidden and one, the closest to the firewall, will require a 1/4" drive, and swivel. I removed the glove box in order to put the replacement blower motor in. It takes a little extra time but allows more room and saves your back. Get a diagram off the internet of how to remove these things. Plug in the new blower motor and test it before you just install it! My biggest fear installing the new blower motor was that it took a lot of force to get it back in on an angle. Almost thought that I was going to crack or damage the fins on the cage. It takes force but just be careful.

Jan 06, 2011 | 2002 Cadillac Deville

1 Answer

How to remove blower motor


Try this procedure...

1. Disconnect the negative battery cable.
2. Remove the instrument panel (IP) storage compartment.
3. Remove the front screw from the right door sill plate.
4. Remove the right hinge pillar trim plate.
5. Disconnect the electrical connectors from the blower motor, as necessary.
6. Remove the bolt from the right lower IP support.
7. Remove the blower motor cover.
8. Remove the motor cooling tube.
9. Remove the blower motor flange screws and ferrules.
10. Perform the following steps in order to remove the blower motor:
Carefully pull the blower motor forward in order to avoid distorting the blower motor fan.
If necessary, pry back the right side of the IP.

11. Inspect the blower motor terminals for distortion.
12. Clean corrosion from the terminals as necessary.
13. Replace the blower motor as necessary.
14. Inspect the flange of the blower motor for damage or distortion that may cause an air leak.
15. Repair the flange as necessary.
16. Inspect the blower fan for any damage and distortion.

zjlimited_239.jpg

Fig. Pull the retaining tab down while turning the blower motor counterclockwise in order to disengage the blower motor

To install:

1. Guide the blower motor and blower fan into position. Be careful in order not to catch the blower fan on any protruding components.
2. Install the blower motor flange ferrules and screws. Tighten the blower motor mounting screws to 20 inch lbs. (2.1 Nm).
3. Install the blower motor cooling tube.
4. Install the blower motor cover.
5. Install the bolt to the right lower IP support.
6. Install the electrical connectors to the blower motor, as necessary.
7. Install the right hinge pillar trim panel.
8. Install the front screw into the door sill plate.
9. Install the instrument panel storage compartment.
10. Install the negative battery cable.
11. Verify the circuit operation.


Hope helps.

Dec 14, 2010 | 1999 GMC Yukon Denali

1 Answer

Connector wire to blower motor


Blower motor pigtail. You can order one from the dealer. I would take an all and try to bend them (in the connector) to make it a more snug fit. Also clean the pins, and put dialectric grease on them. If that doesn't help, the only other solution is a new pigtail.

Mar 27, 2009 | 2003 Buick Rendezvous

1 Answer

Looking for instructions or a diagram of how to install a new blower motor on 1999 chevy silverado


1 Disconnect the electrical connector from the blower resistor
2 Remove the blower motor insulating cover screws.
3 Disconnect the electrical connector from the blower motor
4 Remove the blower motor insulating cover.
5 Pull the retaining tab down while turning the blower motor counter-clockwise in order to disengage the blower motor from the heater/ventilation module (case)
6 Remove the blower motor. Install in reverse order.

Feb 18, 2009 | 1999 Chevrolet Silverado 1500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

14 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...