Question about Holden Cars & Trucks

Open Question

How to remove the head light on a 2006 WM Statesman to replace globes Caprice

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I own a 2008 holden statesman and i have a problem with headlight globes. Every time i change the globe its always dull i have tried cheap ebay globes right up to $300 h.i.d kits and still dull


Hi Michael The issue you have sounds more like a power/earth supply issue. I'm assuming the light lense and reflectors are in good order. The battery is good and no issues with the charging system. Start with the easy side earth or ground side. Connect a seperate earth from light to battery earth terminal just for test purpose. If light is improved then do the same the otherside. if good then you have an earthing problem.(use a slightly heavier gauge wire than your nomal lighting wire so there is no voltage drop). If no different move to power side disconnect connector to globe check and be sure which is the live terminal on the globe and connect a wire as before from + terminal on battery to positive on globe, light must be bright now. Ist check for loose or burnt terminals ie at connection to globe, battery power/ earth terminals.Check Battery to chassis connections for tightness. If easy to do so remove and and clean an re secure. Check engine to battery/chassis connections if all good you have to move onto the supply from fuse box and any connetions in between this is where it becomes more involved and would advise a qualified person to investigate. good luck

Jun 15, 2017 | Holden Cars & Trucks

1 Answer

Remove back seat of a wm 2008 statesman


Put the front seat all the way forward, stand/squat in front of rear seat, grasp under the front of rear seat on both sides and snatch it quickly upwards. Pressure from bent wire rods hold in in, you just have to overcome this pressure.

Aug 26, 2014 | Cars & Trucks

1 Answer

Wl statesman problems


short circuit in the wiring or the blinker stalk is faulty and constanly contacted

Jul 13, 2014 | 2002 Holden Caprice

1 Answer

Overflow tank


try the Holden wreckers for a replacement . many statesman parts are interchangeable with the same year Holden sedan series.. There are after market reservoirs that will fit as well.

Mar 29, 2014 | 2002 Holden Caprice

1 Answer

V6 supercharged statesman wh hard to start every morning its like its out of fuel


Is engine light on? Check for codes . Most likly Tempeture sensor is out of range.

Mar 28, 2014 | 2002 Holden Caprice

1 Answer

Change front parking light


Hi, on the back of your car head light is cover to protect the globes remove the cover and you will see the head light globe and the parking light globe.

Jul 19, 2013 | Mercedes-Benz Cars & Trucks

1 Answer

Head lights


Left the bonnet behind the headlight Remove the head light dust boot and the head light connector then there is a spring type clip holding headlight globe unclip it the fit new globe reclip the spring clip and fit the connector and dust boot

Jan 20, 2012 | 2001 Dodge Dakota

1 Answer

Replace headlight bulb 2006 Point


Under hood, remove large plastic wether cap from back of light, remove 3 point lug from unit, depress the rounded end of the retaining spring inside the open area,
while depressing it push it over to one side to release the pressure off the globe, remove globe, new globe will fit in only one position, be careful not to touch globes end with fingers as the oil in your skin is dtremental to its operation. assmbly is then in reverse. Good luck

Nov 20, 2009 | 2006 Pontiac Grand Prix

1 Answer

Change brake light and head light on 1990 chevy caprice


u have to twist the harnes that keps the bulb in and ull be able to remove the bulb ... the tail lights u have to remove the platic caps and the break light panels have to come out hope this helps

Jan 07, 2009 | 1990 Chevrolet Caprice

1 Answer

How do I change my headlight bulb


go to your parts suppler and ask for a H4 globe pop your bonnet and remove the plug on the back of your head light then remove the rubber boot paying attention to which way it cam off then you will find a spring clip unclip it but be careful not to damage its anchor point. remove old globe an throw away take new globe out of box DO NOT TOTCH THE GLASS OF THE GLOB AS IT WILL CAUSE THE GLOBE TO BLOW STAAIGHT AWAY AFTER FITTING IT handle the globe by the metle bass and fit it, refit spring clip and rubber boot fit the plugf and check the operation of the light

bingo you are done have a nice day

Dec 21, 2008 | 1999 Mitsubishi Mirage

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Holden Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14333 Answers

Are you a Holden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...