Does my 1985 olds tornado have a blend door actuator

Ford Superduty Erratic Temp Blend Door Actuator Removal - YouTube

? 12:29
https://www.youtube.com/watch?v=dYPOtin3JUk
Dec 1, 2013 - Uploaded by FordTechMakuloco
Only buy the Ford Actuators, you can get them cheaper here- ...

Simple how to fix blend door heater a/c actuator 2002 - 2008 ford ...

? 7:12
https://www.youtube.com/watch?v=EEWuJuhCtmc Aug 24, 2013 - Uploaded by kirk colombo
Simple how to fix blend door heater a/c actuator 2002 - 2008 ford explorer noise .... I literary just finish ...

08-10 Super Duty Blend Door Actuator Location - Dual System ...

? 1:24
https://www.youtube.com/watch?v=s7awF2fTKf4 Mar 22, 2012 - Uploaded by srmastertech
Here is a quick view showing the location of the temp blend door actuators on the Ford Super Duty's with ...

Ford blend door fix - 15 minutes - YouTube

? 3:22
https://www.youtube.com/watch?v=wsjGxreGlkA Jul 21, 2013 - Uploaded by SoonersWarriors
Ford blend door fix - 15 minutes. SoonersWarriors. Loading ... Ford Vehicles: Frequent Blend Door Actuator ...

Blend Door Actuator Ford Super Duty 08-10 - YouTube

? 9:45
https://www.youtube.com/watch?v=mbzjCPYENZQ Oct 4, 2013 - Uploaded by MostExcellentDude
This applies to 2008-2010 F250 and F350 with the dual climate control. This video shows the locations for the ...
blend door actuator 2003 ford f450 Google Search

Temperature Blend Door Actuator - RH, EATC Removal and Installation

1. Remove the RH floor console finish panel.

1. Lower the glove compartment.

1. Disconnect the RH temperature blend door actuator electrical connector.
2. Remove the 3 RH temperature blend door actuator screws.
1. Remove the RH temperature blend door actuator.

2006 2010 Ford Explorer NO Heat Passenger Temp Actuator Replacement same as mountaineer

Right side or left ? Electronic Automatic Temperature Control or manual ? Temperature or mode door ?
Temperature Blend Door Actuator - LH Removal and Installation
NOTE: It is not required to install the new LH temperature blend door linkage parts included in the LH temperature blend door actuator service part kit if only the temperature blend door actuator requires replacement and the linkage parts are not broken or binding.
LH temperature blend door actuator and linkage

1. Remove the 2 lower steering column opening cover bolts.

1. Detach the lower steering column opening cover.

1. Disconnect the in-vehicle temperature sensor aspirator hose and electrical connector.

1. Position the instrument panel wire harness away from the LH temperature blend door actuator.

1. Remove the 3 LH temperature blend door actuator screws.

1. Disconnect the LH temperature blend door actuator electrical connector.

1. Remove the LH temperature blend door actuator.

1. Manually operate, and inspect the LH temperature blend door linkage for incorrect placement, binding or damage.

Temperature Blend Door Actuator - RH, Dual-Zone EATC Removal and Installation
NOTE: It is not required to install the new RH temperature blend door linkage parts included in the RH temperature blend door actuator service part kit if only the temperature blend door actuator requires replacement and the linkage parts are not broken or binding.
RH temperature blend door actuator and linkage

1. Disconnect the glove compartment damper from the glove compartment.

1. Remove the glove compartment.

1. Remove the RH lower instrument panel insulator.

1. Remove the RH lower floor console trim panel.

1. Remove the 3 RH temperature blend door actuator screws.

1. Disconnect the RH temperature blend door actuator electrical connector.

1. Remove the RH temperature blend door actuator.

1. Manually operate, and inspect the RH temperature blend door linkage for incorrect placement, binding or damage.
2. Mode Door Actuator - Defrost/Panel/Floor Door
3. Removal and Installation
   NOTE: The defrost/panel/floor mode door actuator can be accessed from below the driver side of the instrument panel.
   NOTE: It is not required to install the new defrost/panel/floor mode door linkage parts included in the defrost/panel/floor mode door actuator service part kit if only the mode door actuator requires replacement and the linkage parts are not broken or binding.
   Mode door actuator and linkage
   1. Remove the 3 defrost/panel/floor mode door actuator screws.
   1. Disconnect the defrost/panel/floor mode door actuator electrical connector.
   1. Remove the defrost/panel/floor mode door actuator.
   1. Manually operate, and inspect the defrost/panel/floor mode door linkage for incorrect placement or damage.
   Mode door actuator linkage only
   
   1. Remove the mode door linkage.
      1. Depress the tab and remove the panel door lever.
      1. Remove the floor/defrost door intermediate lever screw and floor/defrost door intermediate lever.
      1. Pull straight outward to remove the floor/defrost door lever.
   Mode door actuator and linkage
   
   1. NOTE: When installing the mode door actuator, make sure that the panel door lever and floor/defrost intermediate lever are correctly aligned with the mode door actuator cam.
      To install, reverse the removal procedure.

Salvage yard would probably be your best bet. If it is a part that is common to go bad, aftermarket new parts might be available, and if it is not that old you can always get individual pieces from the dealer.

http://www.bing.com/images/search?q=blend+door+actuator+is+on+a+1999+Olds+cutlass&FORM=HDRSC2

The most likely problem is either the blend door actuator or a broken blend door itself.
Both are only accessible by complete removal of the instrument panel(dash).
The blend door actuator can be tested with a Chrysler factory scan tool hooked up to the DLC(data link connector). If blend door actuator is working when tested with the factory scan tool, then blend door itself is at fault.
The only other way to test the blend door actuator is to test for 12v at connector, but you would have to remove the instrument panel in order to gain access to the actuator

check HVAC fuse.if fuse okay heater control module could be the problem.

The most likely cause is a failed blend door actuator; however I recommend a little troubleshooting. First, can you hear a clicking sound behind the dash when you turn the setting to hot? If yes, it is certainly the actuator stripping its gears. If not, check to make sure the heater hoses are both hot as they connect to the heater core at the firewall (in the engine compartment). If one or both of the hoses do not get hot, there is a blockage caused either by an air bubble or a stuck water control valve in the heater hose. If the hoses are both hot, the indication is again the blend door actuator.

Below are instructions for replacing the actuator. Look at the diagrams carefully--the big arrows point to the front of the truck and the actuator is on the side of the heater box above the outlet duct that runs to the driver's side of the floor. Also, the actuator is expensive, so I recommend you make sure it's bad and shop around a bit to get a good price. To check out the actuator, first see if you can turn the blend door by hand. If you can't turn it, maybe it's jammed. Also, reconnect the actuator after removing it and see what it does when you turn the heater to hot.

Removal & Installation

1. Remove the floor air outlet duct extension (1) from the floor duct (2).
   

   

Fig. Remove the floor air outlet duct extension (1) from the floor duct (2)

Disconnect the electrical connection at the blend door actuator (#10 in pic below).

Fig. Blend door actuator and related components

Remove the blend door actuator mounting screws from the HVAC module.

Remove the blend door actuator as an assembly with the actuator cam.

Fig. Remove the blend door actuator mounting screws from the HVAC module

To install:

1. Install the blend door actuator as an assembly with the actuator cam.
   1. Line up the heater/defroster valve lever with the blend door actuator cam slot.
   2. Line up the A/C valve lever with the blend door actuator cam
   
   
2. Install the blend door actuator mounting screw to the HVAC module.
   1. Tighten the blend door actuator mounting screw to 14 inch lbs. (1.6 Nm).
   
   
3. Connect the electrical connection at the blend door actuator (10).
4. Install the floor air outlet duct extension (1) to the floor air duct (2).

Picture of actuator:

there is a blend door actuator for the laredo and if is bad the air wont come out here is a pic of what it looks like and how to get to it


The single zone heater-A/C system is equipped with a single blend door actuator. The dual zone system has two blend door actuators, one for the driver side blend-air door and one for the passenger side blend-air door.

1. Disconnect and isolate the negative battery cable.
   
2. Remove the glove box from the instrument panel.
3. Remove the three screws that secure the blend door actuator to the passenger side of the HVAC air distribution housing .
4. Remove the blend door actuator from the air distribution housing and disconnect the HVAC wire harness connector from the actuator.
5. Remove the blend door actuator from the vehicle

to instal

1. Position the blend door actuator into the vehicle.
2. Install the blend door actuator onto the passenger side of the HVAC air distribution housing . If necessary, rotate the actuator slightly to align the splines on the actuator output shaft with those on the blend door cam .
3. Install the screws that secure the blend door actuator to the passenger side of the air distribution housing . Tighten the screws to 17 inch lbs. (2 Nm).
4. Connect the HVAC wire harness connector to the blend door actuator.
5. Install the glove box into the instrument panel.
6. Reconnect the negative battery cable.

I would look at the air blend doors first, it sound like they are not working or your control in the dash is not working send a signal to them. they work by changing the air from hot to cold or in between.

Avalanche, Sierra And Silverado

1. Remove the floor air outlet duct extension (1) from the floor duct (2). Remove the floor air outlet duct extension (1) from the floor duct (2)
2. Disconnect the electrical connection at the blend door actuator (10). Blend door actuator and related components
3. Remove the blend door actuator mounting screws from the HVAC module.
4. Remove the blend door actuator as an assembly with the actuator cam. Remove the blend door actuator mounting screws from the HVAC module

To install:

1. Install the blend door actuator as an assembly with the actuator cam.
   1. Line up the heater/defroster valve lever with the blend door actuator cam slot.
   2. Line up the A/C valve lever with the blend door actuator cam
2. Install the blend door actuator mounting screw to the HVAC module.
   1. Tighten the blend door actuator mounting screw to 14 inch lbs. (1.6 Nm).
3. Connect the electrical connection at the blend door actuator (10). Blend door actuator and related components
4. Install the floor air outlet duct extension (1) to the floor air duct (2).

C/K Series

1. Disconnect the electrical connector to the mode actuator that is located on the left side of the air distribution case.
2. Remove the screws.
3. Remove the adjuster links from the control lever.
4. Remove the mode actuator.
5. Adjust the mode actuator by completing the following steps:
   1. Connect the electrical connector to the actuator.
   2. Turn the ignition switch to the RUN position. Allow the self-positioning of the actuator.
   3. Turn the ignition switch to the OFF position.
   4. Remove the actuator from the electrical connection. Blend door actuator-C/K Series

To install:

1. Install the mode actuator.
2. Install the screws.
3. Install the adjuster links to the control lever.
4. Connect the electrical connector.
5. Test the circuit operation