Question about Cars & Trucks

Open Question

Some hot water baseboards do not work, but all others work fine on the same floor.

Bled air already

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
professio101
  • 158 Answers

SOURCE: replace brakes. now they go to the floor. bled air

When you fixed the brakes, did you take the lid off the master cylinder. I just wonder if you spilled out your brake fluid. The only reason the pedal should go to the floor is if the brake fluid is gone or the master cylinder is not working. Check the fuse. Check the brake fluid level. The pedal only goes to the floor if there is no back pressure in the lines between the master cylinder the lines to the brake pistion on the calipers. Please give me a good ratin and keep me informed.

Posted on Jul 07, 2009

Ad
ajarema
  • 404 Answers

SOURCE: 1999 Isuzu Rodeo 2.2L. Sometimes the clutch works

Check if there is no fluyid running from underneath the gearbox-engine side, if it is than the inside release bearing is gone.

Posted on Apr 08, 2010

  • 73 Answers

SOURCE: The Defroster, Front Panel, Floor switch will not

bad ristor or relay

Posted on Sep 21, 2010

jturcotte
  • 8514 Answers

SOURCE: no hot air comes out

probably the blend door actuator or cable.

Please see my tip at http://www.fixya.com/cars/r6235876-no_heat_fan_blowing_cold_air . These are generic instructions. If you get stuck or need specific instructions for your car, please get back to me with model, year and engine info.

Posted on Oct 19, 2010

  • 1 Answer

SOURCE: i cant seem to get

Give me some more information about this problem. May be i can help.

Posted on Jul 15, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2006 chevy trailblazer brake pedal going to floor already changed master cylinder brake still going to floor what could be the problem


There is a leak in the system.....the system is full of air and not bled properly.....the new master cylinder is defective

Jan 06, 2016 | Cars & Trucks

1 Answer

2007 Vito 115 heater only works now and again.


you have a air pocket in your line if you have done any work to heater or replaced water pump there is a pocket of air in it let me guess you have heat when you give it gas but when stopped no heat system needs bled to get air out

Jan 13, 2014 | Mercedes-Benz Cars & Trucks

1 Answer

Heater doesn't get hot


have the coolant system pressure bled to remove all the air out of the system and remove the air lock preventing hot water from getting to the heater core

Dec 01, 2013 | 1990 Chevrolet Lumina

1 Answer

List of things i've tried already


you should have called a mechanic long time ago sounds like might be water pump .you might have a blown head gasket too

May 13, 2013 | 1991 Honda Accord

1 Answer

I have a 1992 toyota sr5 pickup 4 wheel drive. I have changed the brake pads on the front and bleed the lines for air. Brakes went on fine and after bleeding the brakes I thought everything was ok. But,...


Some Toyotas need to be cross-bled. You should also check your bleeder valves to make sure you tightened them securely. Look for leaks at the master cylinder and possibly a rear wheel cylinder. Re-bleed the system.

Jun 23, 2010 | 1992 Toyota Pickup

1 Answer

Honda Luxline 1500 16v getting hot.


most common fault,have you bled ALL the air out of the water system?????

Jun 07, 2010 | 1993 Honda Civic 4 Door

3 Answers

Just replaced master cylinder on 1990 aerostar and bled the brakes, still the pedal goes to floor and i have no brakes


Did you bench bleed the master cyl. before installing it? then when you installed the new master, did you bleed all 4 points? If yes, then check all for points for leaking caliper/s and leaking wheel cylinder/s. If the van has ABS, check the valve body for a bleeder screw and see if air bleeds out of it. If you've checked everything twice and did everything right then your new master cyl. may be defective.

Apr 29, 2009 | 1986 Ford F 250

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...