Question about 2000 Dodge Durango

Open Question

Remove and install the rear end on a dodge durango 2000 2wd

Posted by on

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 217 Answers

SOURCE: getting rear gears out of the difential case 1999 dodge durango

  1. Raise and support vehicle. Ensure that the transmission is in neutral.
  2. Remove wheel and tire assembly.
  3. Remove brake drum. Refer toBrakes, for proper procedure.
  4. Clean all foreign material from housing cover area.
  5. Loosen housing cover bolts. Drain lubricant from the housing and axle shaft tubes. Remove housing cover.
  6. Rotate differential case so that pinion mate gear shaft lock screw is accessible. Remove lock screw and pinion mate gear shaft from differential case
  7. Push axle shaft inward and remove axle shaft C - clip lock from the axle shaft
  8. Remove axle shaft. Use care to prevent damage to axle shaft bearing and seal, which will remain in axle shaft tube.
  9. Inspect axle shaft seal for leakage or damage.
  10. Inspect roller bearing contact surface on axle shaft for signs of brinelling, galling and pitting. If any of these conditions exist, the axle shaft and/or bearing and seal must be replaced

Posted on Feb 11, 2009

  • 1986 Answers

SOURCE: where do I place the jack on a 2003 Dodge Durango

place the jack under the passenger door about 6-12 inches away from the wheel and about 6 inches in from the edge of the car. You just need to make sure it's on part of the frame. Do no jack it up via the wheel assembly or the undercarriage

Posted on Sep 14, 2009

chuckster57
  • 1102 Answers

SOURCE: How to remove passenger side

  1. Raise and safely support the vehicle securely on jackstands.
  2. Ensure that the transmission is in Neutral .
  3. Remove the wheel.
  4. Remove the brake drum.
  5. Clean all foreign material from the housing cover area.
  6. Loosen all housing cover bolts, and remove all but two bolts on the top and two on the bottom.
  7. Use a prybar to pry the cover loose from the axle.
  8. Allow the gear oil to drain from the housing.
  9. Remove the axle housing cover.
  10. Rotate the differential case so that the pinion mate gear shaft lock screw is accessible. Remove the lock screw .
  11. Remove the pinion mate gear shaft from the differential case.
  12. Push the axle in towards the center of the vehicle and remove the C-lock from the groove on the axle shaft.
  13. Pull out and remove the axle shaft.
  14. Remove the axle shaft seal from the end of the axle tube with a small prybar.


NOTE The seal and bearing can be removed at the same time with the bearing removal tool.
  1. Remove the axle shaft bearing from the axle tube using an appropriate puller.

Posted on Aug 09, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to install new back brakes fluid lines to a 1998 dodge durango?


10 mm French goes to the Chuck on rear end to the rear of break drum

May 24, 2015 | 1998 Dodge Durango

1 Answer

How do i pull rear wheel bearings


Replacing outer wheel bearings on a solid axle rear end is a moderately involved operation.

The rear axle cover has to come off so that you can remove the C clips to allow the actual axle to come out. Once out, a bearing puller is needed to remove the old bearing, and a bearing installed may be needed to drive in the new one.

If this sounds out of your comfort zone, a shop should charge $200-$300 to make the repair.

Jun 30, 2010 | 1999 Dodge Durango

2 Answers

Egr valve dodge durango


if this is a 4.7l engine, the valve is on the left rear of the intake. loosen the 8mm bolts that hold the egr intake tube to the egr valve, remove the egr bolts, disconnect wiring, remove valve and tube together, attach intake tube loosely to new valve, install new valve, tighten tube bolts to egr using a swivel socket, this is not a 5 minute job, so dont attempt unless you have some time and patience.

Apr 17, 2009 | Dodge Durango Cars & Trucks

1 Answer

On my 2002 DODGE DURANGO ABS and Brake lights stay on


I have a 2002 I had to take the sensor out of the rear end. It is located on top. remove the screw and it should pop out. Be carefull. I had to clean it off and re-install. After that it went off this is something to try.

Nov 17, 2008 | 2002 Dodge Durango

Not finding what you are looking for?
2000 Dodge Durango Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7688 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...