Question about Cars & Trucks

Open Question

How do I reset my dave t83 - Cars & Trucks

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

If I hold battery cables together will it reset my ecm does car have to be running


hello,
knowing the year and make would help but it will still work, remove the cables and let stand for approx 5 mins. then clean the battery and the cables then reinstall. the car that you are working on depends on how the car will relearn the parameters as you drive, some take longer and some not so long. that is all that you have to do,good luck, dave

Jun 25, 2016 | Cars & Trucks

1 Answer

Does the Kia Sorento 2006 needs a Fuse or something to reset Cruise Control? Thanks Dave


Not really. It is controlled by the ECM. If that fuse blew, you would have lost many other things, like engine not starting.

Jul 19, 2015 | Kia Cars & Trucks

1 Answer

I have a 1995 oldsmobile 88 and the computer needs to be reset.


Hi Dave.

You can perform a reset of main control module (ECM) disconnecting the battery terminals for a couple of minutes. That will reset the check engine light until the problem occurs again. Make sure that you have the stereo anti theft code if needed.

The proper way to reset the DTC codes is using an OBDII scanner. The job can be done at the dealer place or at any authorized garage for a small fee (half hour labor). In US the scan and reset can be done for free at Autozone. If possible go to the nearest Autozone, ask to do a code scanning take note of codes and ask to reset the ECM.

Finally, you can reset the codes at home using a scanner tool like this:OBDII Scanner - U480.

Regards



Regards.

Ginko

Sep 09, 2011 | 1995 Oldsmobile 88

1 Answer

How do I reset the computer on my 2004 Astro Van? The mechanic says it has to be reset to see if the error code comes up again, and then take it to him, but he has no time for me to go to have it reset...


Hi Dave.

The proper way to reset the DTC is using an OBDII scanner. Go to the nearest Autozone, ask to do a code scanning and to reset codes.

You can also reset the codes at home but you will need a scanner like this:OBDII Scanner - U480.

Here an example showing how to use a scanner tool to reset the codes.

You can also try disconnecting the battery. That will reset the engine check light until the problem occurs again. It may not clear stored diagnostic codes. Make sure that you have the stereo anti theft code if needed.

Regards.

Ginko

Sep 09, 2011 | 2004 Chevrolet Astro

1 Answer

I have a 2002 toyota camry had to change the battery, and the car will not idle, have driven it for about an hour


Disconnect the battery for 30 minutes. This will flash the ECU and reset the cars values. It will take 1-200KM's for the ecu to read all the values and settle and the car to return to normal

Cheers
Dave

Mar 19, 2011 | 1995 Toyota Camry

1 Answer

My range rover has got an eas fault showing and its dropped to its buffers whats themost likely cause


if the pump has run for over 15mins it will go eas
if you unplug ecu [ bottom one under pasenger seat] do not have key in or enging running it may reset if this is a no go it will have to be plugged in and reset
yours dave

Mar 12, 2010 | 1996 Land Rover Range Rover

1 Answer

Doorlocks keep locking even when out of the


Dave, it would appear that at one point one of the manual locks were forced either to unlock or lock and has now repositioned the nuetral point at a different location on the locking rod, hence, sending false readings to the control unit to either unlock or lock, I would try this, close all doors and manually lock them see which lock lever look unlike the rest in that position, this will be the culprit and have to be reset on the rod behind the door trim panel. This advice is as best as I can give without manually seeing the car. Drive safely

Jan 19, 2010 | 1999 Pontiac Montana

1 Answer

2005 cheverolet silverado won't start


Hey Dave......Try pulling the ECM Fuse for about 5 Min. to reset the Computer and see what we get. Let me know so that we can go Further if Needed!

Jan 12, 2009 | 2005 Chevrolet Silverado 1500 2WD

1 Answer

2003 Ford Focus hesitation from stop when step on gass pedal.


sounds like you need to have it put on a scanner to check the tps sensor it could be off and nead to be replaced or reset

Nov 23, 2008 | 2003 Ford Focus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

14 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...