Question about Renault Cars & Trucks

Open Question

I Just Fitted New Front & Rear Brake Pads + Rotors To A Renault Master Van 2013 Mod (Pads Had New Were Indicators In Them) And The Brake Were Indicator Didn't Self Cancel. Any Suggestions

Vin :- VF1MAFEFCD0680693

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
fixincars
  • 335 Answers

SOURCE: Front Brake Pads locked up on Rotor

Have the brake pads been so very work they are down to the metal? This could cause the caliper piston to extend too far and not be able to retract properly.
Calipers Fail mostly from a cut in the rubber boot around the pistion dirt and debris get in there and rust the piston and it cannot retract properly Do they retract after they cool Down? if so the brake fluid has "boiled" if brake fluid is not changed about every 24,000 miles condensation builds up and lowers the boiling point of the brake fluid causing this problem.
Tell me does it happen after a long drive or siting a long time in heavy bumper to bumper traffic in hot summer weather? I recommend a complete brake fluid flush an change the calipers with NEW ones ot rebuilt and use dielectric grease on all points of metal to metal contact between the caliper an the mount bracket and thee ends of thee pada n the slide points they ride on and the pins that go through thecaliper and thread into the mount only dielectric not regular grease it will cause sticking and a worse problem than you have now.

Posted on Aug 25, 2008

Ad
michigan man
  • 3533 Answers

SOURCE: front brake pads & rotors on 2003 buick park avenue

first you put the car on stands and and then you take the two bolts out in back of the caliper and remove the caliper and then remove the pin in the center of the rotor and the nut and then take the rotor off and do not forget to repack the bearing with grease and then put it back together take one side apart at a time.just in case you need to take a look at how it goes back together

Posted on Mar 02, 2009

emissionwiz
  • 76630 Answers

SOURCE: ABS light on after replacing the front and rear brake pads .

u will need to check the wheel speed sensors behind the brake rotors to see if they got damaged or disconnected during the brake job, as long as the ABS light is on the Anti-lock brake system is disabled, regular braking without the need of ABS will feel fine.

Posted on Apr 01, 2009

shadtremonky
  • 353 Answers

SOURCE: cant depress brake caliper to replace pads

disc brakes on the rear of a vehicle have a screw out mechanism that attaches to the ebrake . this means that you must turn the caliper piston to recess into the cylinder.
open the bleed screw to make it move eazier.

Posted on Sep 21, 2009

Testimonial: "thanks for "bleed valve" tip. I had to take the whole caliper off due to debris in the chamber,the brakes have not been maintained prior to me."

  • 61 Answers

SOURCE: abs light stays on 1995 chevy pickup

Probably want to check abs sensors on the back side of the wheels. Did you have a abs light on before the brakes where done?

Posted on Feb 04, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I ave a low growling noice and brake pedal pulses


As a general rule, if the wheel shakes when you apply the brakes, the front disk rotors are warped. If the brake pedal pulses when you apply brakes, the rear brake rotors are warped. So you most likely have warped rear brake rotors. The noise may be that the wear indicators on the brake pads are touching the disks, indicating that you need new brake pads. Given both of these, I suggest a trip to the local brake repair centre is needed.

Feb 24, 2016 | 2001 Chrysler LHS

1 Answer

Land cruiser 2005 troop carrier brake stopping power is poor


Probably there is a leak in the hydraulic brake line hoses connecting the master and the wheel cylinder hose. Also get the brakes bleeded to remove any air the system. also get the check valve of the brake booster checked and the vacuum hose.

Jun 27, 2013 | 2005 Toyota Land Cruiser

1 Answer

1993 ford e350 cutaway


brake fluid hose towards the front wheels in the brake master is blocked.

Jun 20, 2013 | 2002 Ford E350

1 Answer

My 2007 nissan quest 3.5S mini van is in almost perfect condition until I recently discovered something deviating from what I know is common to brakes. I do all maintenance work to my cars (nissan VW,...


Master cylinder and/or brake booster could be the problem. A tiny bit of air in the system will effect your braking abilty. A fault in the ABS system would prompt the computer to trigger the ABS light. If you have brake shoes on the rear, make sure they are properly adjusted. Hope this helps.

Jul 04, 2011 | 2007 Nissan Quest 3.5 Minivan

2 Answers

Rear pad removal?


Here ya go! This is for the rear brake pads removal:

Removal & Installation
  1. Remove the brake master cylinder filler cap. Check brake fluid level in brake master cylinder reservoir. Remove fluid until brake master cylinder reservoir is half full.
  2. Raise and support the vehicle.
  3. Remove the wheel and tire assembly.
  4. Inspect the brake pads for wear or contamination. If worn, damaged or past specification, install new components.
  5. Remove the caliper pin bolts.
  6. Remove the rear disc brake caliper.
  7. Remove the brake pads and rail clips.
  8. Inspect the disc brake caliper for leaks. If leaks are found, disassembly is required.
  9. Installation is the reverse of removal. Observe the following torques:
    • Caliper bolts: 27 ft. lbs. (36 Nm)
  10. // // 0) preLoad.src = ctl00_cphLeft_chRepairTreeNav_tvTOC_ImageArray[i]; } ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.lastIndex = 30; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.populateLog = theForm.elements['ctl00_cphLeft_chRepairTreeNav_tvTOC_PopulateLog']; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.treeViewID = 'ctl00$cphLeft$chRepairTreeNav$tvTOC'; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.name = 'ctl00_cphLeft_chRepairTreeNav_tvTOC_Data'; //]]>

May 12, 2011 | 2002 Ford E350

2 Answers

My brakes sound like they are grinding


check rear rotors and front rotors for rust buildup (flahlight helps). does the vehicle shake when you come to a hard stop? You will either need to have a front or rear or both brake job (rotors cut or replaced and new brake pads) If the vehicle is shaking when coming to a stop, its probably your front pads. If your hearing the noise from the rear its the rear pads or it you hear it from the front its the front pads. If there significant rust build up or your pads are low a brake job is recommended.

May 04, 2011 | 2008 Nissan Armada

2 Answers

How to change brake pad and check rotors


Brake Pads Removal & Installation Front for_car_toy_cam_02-04_sst_frt_dsc_asm.gif

To Remove:
  1. Drain brake fluid to ½ full level in reservoir.
  2. Remove the front wheels. toy_car_cam_frontbrakepads.gif

  3. Remove the front brake caliper assembly.
  4. Remove the 2 anti-squeal shims from each of the 2 brake pads.
  5. Remove the wear indicator from each of the 2 brake pads.
To Install:
NOTE: When replacing worn pads, the anti-squeal shims must be replaced together with the pads.
toy_car_cam_frontbrakepads.gif

  1. Using a large C clamp or equivalent press piston into the caliper.
  2. Apply disc brake grease to the inside of each anti-squeal shim.
  3. Install the anti-squeal shims on each pad.
  4. Install the pad wear indicator clip to the pads.
  5. Install the pads with the pad wear indicator plate facing upward.
  6. Install the brake caliper with the 2 mounting bolts. Torque the bolts 25 ft-lb (34 Nm).
  7. Install the front wheels.
  8. Fill the master cylinder with new clean brake fluid.
  9. Pump the brake pedal several times to seat the brake pads.
Rear TMC made rear brake components toy_car_cam_tmcrearbrakes.gif

TMMK made rear brake components toy_car_cam_tmmkrearbrakes.gif

To Remove:
  1. Drain the brake fluid to ½ full level in reservoir.
  2. Remove the rear wheels.
  3. Remove the caliper slide pins.
  4. Remove the caliper slide pin bushings (TMMK made) (Kentucky).
  5. Remove the rear brake calipers.
  6. Remove the 2 brake pads with the anti-squeal shims.
  7. Remove the anti-squeal shims and pad wear indicators from brake pads.
To Install:
  1. Using a large C clamp or equivalent press the piston into the caliper.
  2. Coat both sides of the outer anti-squeal shim with pad grease.
  3. Install anti-squeal shims to each pad.
  4. Install wear indicators on the 2 brake pads.
  5. Install the caliper slide pin bushings (TMMK made) (Kentucky).
  6. Install the rear brake caliper with the slide pins. Torque the slide pins as follows:
    • TMC made (Japan): Torque the caliper slide pin 25 ft-lb (34.3 Nm)
    • TMMK made (Kentucky): Torque the caliper slide pin 34 ft-lb (47 Nm)
  7. Fill the master cylinder with new clean brake fluid.
  8. Pump the brake pedal several times to seat the brake pads.
  9. Install the rear wheels.
prev.gif next.gif Brake Rotor Removal & Installation Front To Remove:
  1. Remove the front wheels.
  2. Remove the front brake caliper assembly.
  3. Remove the front brake pads.
  4. Remove the 2 bolts and caliper mounting bracket.
  5. Place match marks on the disc and axle hub.
  6. Remove the front wheel disc.
To Install:
  1. Align the match marks and install the front disc.
  2. Install the brake caliper mounting bracket. Torque the bolts 79 ft-lb (107 Nm).
  3. Install the brake caliper. Torque the bolts 25 ft-lb (34 Nm).
  4. Install new gaskets and connect the brake hose to the caliper with the banjo fitting bolt. Torque the fitting bolt 22 ft-lb (29.4 Nm).
  5. Fill the reservoir with brake fluid.
  6. Bleed the brake system.
  7. Install the front wheel.
Rear To Remove:
  1. Remove the rear wheels.
  2. Remove the brake caliper assembly.
  3. Remove the brake pads.
  4. Remove the 2 bolts and the caliper mounting bracket.
  5. Place match marks on the disc and axle hub.
  6. Remove the rear disc.
To Install:
  1. Align the match marks and install the rear disc.
  2. Install the rear brake caliper mounting bracket. Torque the bracket bolts as follows:
    • TMC made (Japan): Torque the bracket bolt 46 ft-lb (61.8 Nm)
    • TMMK made (Kentucky): Torque the bracket bolt 34 ft-lb (47 Nm)
  3. Install the rear brake caliper with the slide pins. Torque the slide pins as follows:
    • TMC made (Japan): Torque the caliper slide pin 25 ft-lb (34.3 Nm)
    • TMMK made (Kentucky): Torque the caliper slide pin 32 ft-lb (43 Nm)
  4. Install new gaskets and connect the brake hose to the caliper with the banjo fitting bolt. Torque the fitting bolt 22 ft-lb (29.4 Nm).
  5. Fill the reservoir with brake fluid.
  6. Bleed the brake system.
  7. Install the rear wheel
prev.gif next.gif

Jan 25, 2011 | 2007 Toyota Camry

2 Answers

I am having difficulty installing rear brake rotors over the parking brake pads. The star wheel adjusters are all the way in and the new rotors do not want to go on over the new pads


you have to loosen the emergency brake adjustment on the cable give it some slack push the shoes together by hand and rotor will fit . please dont forget to rate this answer . hope this helps

Jul 28, 2010 | 1995 Toyota Camry

1 Answer

Rear brake pads junk rotors junk front pads full,uneven,low miles


emergency brake cable may not have been adjusted properly or emergency brake may have been partially engaged without brake light indicating such. Check brake release handle, if it makes no noise as to indicate realease, then it would have to be the e brake adjustment or frozen brake cylanders that when brakes are applied the pressure presses the shoes against the drums but does not release pressure, could be bad cylanders but not likely on both sides at the same time.

Jan 06, 2009 | 2003 Chevrolet Express

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top Renault Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

xxxxxx xxx

Level 3 Expert

4869 Answers

yadayada
yadayada

Level 3 Expert

76630 Answers

Are you a Renault Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...