Question about 2007 Hyundai Entourage Limited Minivan

1 Answer

How do you get to the turn signal bulb for replacement on the passanger front?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 382 Answers

Dear friend-sometimes these bulbs corrode and is difficult to remove use protection when attempting to replace the globe.

Posted on Jul 21, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Front turn signals not working.


Probably the switch. Use a Digital Volt Meter and check for B+ at the socket of each item with the switch in the on position. If B+ not found then bypass switch terminals and jump the switch with home made jumper wires according to repair manual instructions. If bulbs light the switch is your culprit .But before you do all this check each socket for rust and tightness. Good luck

Mar 11, 2014 | 2004 Chevrolet Venture Passanger

1 Answer

Passanger side brake lights wont turn on when brake pedal is pushed


You didn't say what the car model was but some cars have the same lamp as the turn sig. So check your left turn signal and also the front left turn signal light bulb to see if they both are flashing.

Sep 23, 2012 | 2007 Subaru Impreza 2.5i

1 Answer

Right rear turn signal and break light one in the same not working replace bulb and still not working. All other lights and functions working the front passanger turn signal work fine. Id there a relay...


Check the new bulb make sure it is a 4157 bulb. If it is the correct bulb, try switching the left and right bulbs to see if the problem is still on the right side. Check the wiring on the right side, look for damaged or disconnected wiring.

Dec 26, 2010 | 2005 Chevrolet Cobalt

1 Answer

The passanger side front turn signal won't flash, the rear flashes very fast. I replaced the front passanger side lamp, this did not. can you help me?


the light socket is prob bad, the fast flashing is a built in warning to let you know a turn signal light is out so the "revenue generators" , ( police) cant give you an outragous fine

Oct 20, 2010 | 1997 Ford F150 Regular Cab

1 Answer

Passanger side turn signals don't work


First: press the brake and be sure that both sides light up. If one side does not, turn your attention to it. Remove the taillamp assembly from the suspect side and disconnect it. Unscrew the socket / circuit board and dismount it from the reflector. Take out the bulbs and examine the sockets, looking for melted / toasted / warped sockets. If they are bad, don't even bother trying new bulbs or attempting a repair; go to the parts store and get a new socket / circuit board assembly. Last I looked they cost about $25 apiece.

Nov 16, 2009 | 1988 Chevrolet K2500

1 Answer

What does failed front rh indictor means


Your front passanger side turn signal bulb is burnt out.

Sep 11, 2009 | 2000 Jaguar S-Type

1 Answer

Need to replace passanger from truning signal


Pop the hood and on the back of the assembly, there should be two white tabs that you pull up to release the headlamp unit. Once you disconnect the wire harness, you can pull it out and open the covering to replace the signal bulb

Aug 25, 2009 | Buick Century Cars & Trucks

1 Answer

Change front passanger blinker


Open the hood and look for a small screw or bolt holding the signal light assembly on by the fender.
Remove this and pull just the signal light assembly straight forward.
Not the whole headlight assembly.
Twist and turn the bulb socket to remove the light from the rear of the light assembly.
Check the # and color of your bulb and get a replacement.
Push in and turn to remove the bulb.

Aug 12, 2009 | 1998 Chevrolet Cavalier

2 Answers

Left Turn Signal Rapidly Blinks


Sounds to me like a bad ground. When the current can't complete through a ground circit it feeds back through the elements ancd can cause all sorts of wierd syptoms.

The fast blink itself can be casued by a burnt out bulb I would check that first.

Then I would check the trailter harness if there is one and unpluch any harness that may be plugged into it. also check each bulb to see if it is seated well. you may be able to see if there is corrorsionaround the bulb terminals at this time is so yo may need to replace the light assembly. Also you could look for any spot where maybe someone in the past tried to tie into the harness to hook up additional lights etc. this may allo moisture in and corroded to the point the wire is "open"

Apr 06, 2009 | 2002 Chevrolet Venture Passanger

Not finding what you are looking for?
2007 Hyundai Entourage Limited Minivan Logo

593 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8266 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...