Question about Pontiac Cars & Trucks

1 Answer

I have an 04 Pontiac grand am with all brake lights working but now my third brake light stopped working. So I changed bulbs I noticed they had all burnt out. . Is there a fuse im not aware of. Thanx

Posted by on

  • swaffken Dec 11, 2016

    yes there is a fuse in the fuse block

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Pontiac Master
  • 14,585 Answers

If your rear brake lights are working, the fuse is good. Check the wiring.

Posted on Dec 11, 2016

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1114 Answers

SOURCE: Left rear brake light stopped working but bulb and fuses are OK.

take the bulb back out have someone sit in car apply brake get your self a circuit tester and check to see if this circuit is carrying efficient 12 volt current! some times in cold weather these bulbs get hot with long period of breaking and when released condensate and rust begins and you get what you have perhaps bad socket! this would be a ideal location to begin and probably end,

Posted on Jan 03, 2009

  • 1 Answer

SOURCE: need 02 trailblazer third brake light removal

Open the full hatch.
Pull down the weather strip near the rear dome light.
There should be a wire with a connector in it. Disconnect it
Close the full hatch.

Open just the window hatch. There is 1 screw on either side of the bulb housing.

Posted on May 01, 2009

honeymokey
  • 3113 Answers

SOURCE: main brake lights not working/third brake light ok

Turn signal switch.

Posted on Jul 02, 2009

johnjohn2
  • 5763 Answers

SOURCE: 2005 grand cherokee brake lights out. changed

checked all fuses even under hood? may have bad signal switch or bad brake light switch yes even if 3rd brake works.also check wiring under rear fender by bumper thats were wire harness is hope this helps.

Posted on Oct 09, 2009

ftw1952
  • 10319 Answers

SOURCE: Both main brake lights are out, third brake light works.

Replace the brake light switch located by the brake pedal. That will resolve your problem

Posted on Apr 09, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

99 grand marquis third brake light dosen't work


From That Light There Is Only 2 Wires , Trace Them Back To The Tail Light Connection - Most Likely A Split Wire Or Bad Connectio

Dec 11, 2013 | 1999 Mercury Grand Marquis

1 Answer

Enter brake light Pontiac grand am not working changed bulbs


Could be the brake light switch located above brake pedal.

Nov 13, 2011 | 2003 Pontiac Grand Am

1 Answer

Sent an email earlier before I finished the situation. 2000 Pontiac Grand Prix GT. Brake lights will not work. I have replaced all bulbs, running lights work, third brake light in window works, turn...


has to be somwhere in the wiring for the tail lamp brk light. if the high mount works the switch is good. did you put the correct bulbs in? they may share a common ground independant of the other lights.

Nov 19, 2010 | 2000 Pontiac Grand Prix

1 Answer

1995 cutlass ciera stop light and third light don't work


THE 3RD BRAKE LIGHT DOES NOT GO THROUGH THE TURN SIGNAL SWITCH.ASSUMING THE 3RD BRAKE LIGHT BULB IS GOOD.U SHOULD CHECK THE BRAKE LIGHT SWITCH ON THE BEAKE PEDAL.SHOULD BE POWER GOING IN & POWER OUT WHEN U ARE IN THE BRAKE

May 13, 2009 | 1995 Oldsmobile Cutlass Ciera

1 Answer

How to cchange the third brake light bulb


1992–98 GRAND AM AND ACHIEVA
  1. Disconnect the negative battery cable.
  2. Pull the center high-mount stop lamp cover to disengage the retaining tabs.
  3. Unfasten the lamp retaining screws.
  4. Remove the sockets using a suitable prybar to release the retaining tabs.
  5. Detach the bulbs from their sockets.
  6. Using a suitable prybar to release the tabs, remove the lamp lens. Fig. 14: View of the center high-mount stop lamp assembly — 1995 Grand Am and Achieva shown

Apr 04, 2009 | 1998 Pontiac Grand Am

1 Answer

2002 Jeep Grand Cherokee no back lights


its either a brake light switch or brake light bulb socket not making contact in back because the piece where it makes contact brakes easily.,first check if third brake light on top of your rear door is working, if it is its not the brake light switch

Sep 24, 2008 | 2002 Jeep Grand Cherokee

1 Answer

Pontiac grand am 2004 left brake light and center mount


look at the contact point were the bulb makes its connection.if it is dirty clean it and put electrical grease on it.

Jun 25, 2008 | 2004 Pontiac Grand Am

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...