Question about Cars & Trucks

Open Question

Assembling the steam buttons Snbeam 6850 Resillium

When I disassembled the button right hand the ball bearing spring and washers separated I would like to BE sure of the correct assembly

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 92 Answers

SOURCE: i need to replace the crusie control buttons

disconnect batt.wait 5 minutes,push brake several times,locate airbag fuse and remove.this is improtant as you will have to remove drivers airbag.there are 2 round plastic caps covering the 2 airbag bolts located at back of steering wheel by the cruise switches.remove caps remove the 2 8mm bolts.remove airbag,set airbag away from you with plastic cover of airbag up.replace switches.reinstall airbag,reinstall fuse.reconnect batt.

Posted on Oct 21, 2008

Ad
  • 1 Answer

SOURCE: Stuck Right Front Wheel Bearing Assembly

With a "puller" or if that doesn't work the old hammer and chisel all around the parting line till it frees up.

Posted on Nov 11, 2008

  • 4 Answers

SOURCE: 92 Miata transmission shift boot replacement

The lower shifter boot is attached to the transmission by 3 10mm bolts. You will need to remove to center consoule and the upper shift boot that attaches to the car to be able to remove the lower boot. Then you can replace the lower boot.

Posted on Jan 04, 2009

jgwhomeequip
  • 1902 Answers

SOURCE: Stuck Right Front Wheel Bearing Assembly

Best bet is to get at it with a hammer and screw driver or chisel and try to break it free. When your wheel bearing freezes like that sometimes welds itself to the axle. Very hard to remove

Posted on Feb 07, 2009

  • 543 Answers

SOURCE: 1996 saturn sl front wheel bearing assembly

you got to press it in and out,and if u dont do it right with the proper tools you will wreck the hub

Posted on Oct 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1999 toyota prado


where are you hands, we car blind here,

ball bearings are everywhere. car has 1500 to 3000 parts.
even the steering shaft has bearings.
inside car, outside car.
engine, transmissions, wheel bearings. axle bearings, CV balls.
where.

May 27, 2014 | 1999 Toyota RAV4

1 Answer

Replace cv joints


Hi Douglas, I'm glad to help. My first suggestion is to get to complete shaft. This way you want have any problems later on. It's not that much more expensive and you'll be glad you did. Below is the procedure for replacing them.



FRONT DRIVESHAFTS

REMOVAL
  1. Raise vehicle on jack stands or centered on a frame contact type hoist. Refer to Hoisting in the Lubrication And Maintenance section of this manual for the required lifting procedure to be used for this vehicle.
  2. Remove the cotter pin and nut lock Hub And Bearing To Stub Axle Retaining Nut from the end of the stub axle.
  3. Remove the wheel and tire assembly from the vehicle.
  4. Remove the wave washer Wave Washer from the end of the stub axle CAUTION: Wheel bearing damage will result if after loosening hub nut, vehicle is rolled on the ground or the weight of the vehicle is allowed to be supported by the tires.
  5. With the vehicle's brakes applied to keep hub from turning, loosen and remove the stub axle to hub nut.
  6. Remove the two front disc brake caliper to steering knuckle attaching bolts Front Disc Brake Caliper Attaching Bolts
  7. Remove the disc brake caliper from the steering knuckle. Caliper is removed by first rotating top of caliper away from steering knuckle and then removing bottom of caliper out from under machined abutment on steering knuckle Brake Caliper Mounting To Steering Knuckle
  8. Support disc brake caliper assembly by using a wire hook and suspending it from the strut assembly Correctly Supported Disc Brake Caliper Do not allow the brake caliper assembly to hang by the brake flex hose.
  9. Remove the brake rotor from the hub and bearing assembly Remove/Install Brake Rotor
  10. Remove nut attaching outer tie rod end to steering knuckle Removing Tie Rod End Attaching Nut Nut is to be removed from tie rod end using the following procedure, hold tie rod end stud with a 11/32 socket while loosening and removing nut with a wrench.
  11. Remove tie rod end from steering knuckle using Remover, Special Tool MB-991113 Tie Rod End Removal From Steering Knuckle Arm
  12. Remove the steering knuckle to ball joint stud, clamping nut and bolt Control Arm To Steering Knuckle Attachment from the steering knuckle.
  13. Using a pry bar, separate steering knuckle from ball joint stud Separating Ball Joint Stud From Steering Knuckle Note: Use caution when separating ball joint stud from steering knuckle, so ball joint seal does not get cut. NOTE: Care must be taken not to separate the inner C/V joint during this operation. Do not allow driveshaft to hang by inner C/V joint after removing outer C/V Joint from the hub/bearing assembly in steering knuckle, end of driveshaft must be supported.
  14. Pull steering knuckle assembly out and away from the outer C/V joint of the driveshaft assembly Steering Knuckle Separation From Driveshaft
  15. Support the outer end of the driveshaft assembly. Insert a pry bar between inner tripod joint and transaxle case Disengaging Inner Tripod Joint From Transaxle Pry against inner tripod joint, until tripod joint retaining snap ring is disengaged from transaxle side gear.
  16. Hold inner tripod joint and interconnecting shaft of driveshaft assembly. Remove inner tripod joint from transaxle, by pulling it straight out of transaxle side gear and transaxle oil seal Tripod Joint Removal from Transaxle When removing tripod joint, do not let spline or snap ring drag across sealing lip of the transaxle to tripod joint oil seal.
INSTALLATION
  1. Thoroughly clean spline and oil seal sealing surface, on tripod joint. Lightly lubricate oil seal sealing surface on tripod joint with fresh clean transmission lubricant.
  2. Holding driveshaft assembly by tripod joint and interconnecting shaft, install tripod joint into transaxle side gear as far as possible by hand Tripod Joint Removal from Transaxle
  3. Grasp inner tripod joint an interconnecting shaft. Forcefully push the tripod joint into side gear of transaxle, until snap ring is engaged with transaxle side gear. Test that snap ring is fully engaged with side gear by attempting to remove tripod joint from transaxle by hand. If snap ring is fully engaged with side gear, tripod joint will not be removable by hand.
  4. Clean all debris and moisture out of steering knuckle, in the area were outer C/V joint will be installed into steering knuckle.
  5. Ensure that front of outer C/V joint which fits against the face of the hub and bearing is free of debris and moisture before installing outer C/V joint into hub and bearing assembly Outer C/V Joint Inspection
  6. Slide drive shaft back into front hub and bearing assembly. Then install steering knuckle onto the stud of the ball joint assembly Steering Knuckle Separation From Driveshaft
  7. Install a new steering knuckle to ball joint clamping bolt and nut Control Arm To Steering Knuckle Attachment Tighten the clamping bolt and nut to a torque of 135 N·m (100 ft. lbs.)
  8. Install tie rod end into steering knuckle. Start attaching nut onto stud of tie rod end. While holding stud of tie rod end stationary using a 11/32 socket, Removing Tie Rod End Attaching Nut tighten tie rod end to steering knuckle attaching nut. Then using a crowfoot and 11/32 socket Torquing Tie Rod End Attaching Nut , tighten the tie rod end attaching nut to a torque of 54 N·m (40 ft. lbs.)
  9. Install braking disc on hub and bearing assembly Remove/Install Brake Rotor
  10. Install disc brake caliper assembly on steering knuckle. Caliper is installed by first sliding bottom of caliper under abutment on steering knuckle, and then rotating top of caliper against top abutment Brake Caliper Mounting To Steering Knuckle
  11. Install disc brake caliper assembly to steering knuckle attaching bolts Front Disc Brake Caliper Attaching Bolts Tighten the disc brake caliper assembly attaching bolts to a torque of 22 N·m (195 in. lbs.)
  12. Clean all foreign matter from the threads of the outer C/V joint stub axle. Install the washer and stub axle to hub/bearing assembly nut on stub axle and securely tighten nut.
  13. Install front wheel and tire assembly. Install and tighten the wheel mounting stud nuts in proper sequence until all nuts are torqued to half the required specification. Then repeat the tightening sequence to the full specified torque of 135 N·m (100 ft. lbs.)
  14. Lower vehicle.
  15. With the vehicle's brakes applied to keep hub from turning, tighten the hub nut to a torque of 244 N·m (180 ft. lbs.) Torquing Front Stub Axle To Hub Nut
  16. Install the spring wave washer on the end of the stub axle.
  17. Install the hub nut lock, and a new cotter pin Hub And Bearing To Stub Axle Retaining Nut Wrap cotter pin prongs tightly around the hub nut lock as shown in Hub And Bearing To Stub Axle Retaining Nut
  18. Check for correct fluid level in transaxle assembly. Refer to Group 21, Transaxle for the correct fluid level checking procedure for the type of transaxle being checked.
  19. Set front toe on vehicle to required specification.

May 07, 2014 | 2000 Dodge Caravan

1 Answer

How do you replace front broken coil spring on 1998 ford windstar? do you have a diagram, pictures or video?


Strut and Spring Assembly Removal
  1. Raise the vehicle on a hoist.
  1. Remove the front wheel and tire assembly.
  1. ani_caut.gif CAUTION: To avoid damage to the 6mm drive hole in the front stabilizer bar link ball stud, do not use an Allen wrench to break loose or tighten to final torque the front stabilizer bar link-to-front shock absorber nut.
    Remove the stabilizer bar link retaining nut and disconnect the link from the strut.


f8740a.gif

  1. ani_caut.gif CAUTION: Do not allow the halfshaft to move outboard. Over extension of the CV joint may result in the separation of internal parts, causing failure of the joint.
    Remove the strut assembly-to-steering knuckle pinch bolt. If required, slightly spread the steering knuckle to ease the removal of the strut. Pry down on the lower control arm and roll the strut base out of the knuckle. Do not pry on the halfshaft, as damage may result. Wire the steering knuckle up to prevent the halfshaft from moving outboard.
  1. Partially lower the vehicle.
  1. Support the strut assembly and remove the top three mount-to-strut tower nuts. Remove the strut assembly from the vehicle.


f9154a.gif

  1. ani_caut.gif CAUTION: The strut assembly is under spring tension. Attempting to disassemble the strut without properly compressing the spring can result in injury.
    Using a suitable spring compressing tool, slightly compress the strut spring to relieve initial tension. Loosen the upper rod nut. Continue to compress the spring until the tension is relieved. Remove the upper rod nut.


f3897c.gif

  1. Remove all upper mounting parts, coil spring, and coil spring isolators from the strut and save them for reassembly. Carefully note the position of each part during removal to ensure proper reassembly. Inspect each part for wear and damage as it is removed.
Installation
  1. ani_caut.gif CAUTION: The bearing and seal assembly is press-fit onto the upper mount. The mount washers must be installed in the correct orientation.
    NOTE: Be sure to check the spring insulator for damage before assembly. If the outer metal splash shield is bent or damaged, it must be carefully bent back, so it does not touch the locator on the bearing and seal assembly.

    NOTE: New gas struts are shipped with the rod in a locked down position. To extend the new strut, remove the external tie down and/or rotate the upper end of the rod, counterclockwise.

    Install the coil spring insulator, coil spring, and upper mounting parts to the new strut assembly. Make sure the spring is correctly seated in both spring seats.


f8737a.gif


Item Part Number Description 1 ? Dust Boot (Part of 18045) 2 N803826-S100 Front Shock Absorber Mounting Bracket Nut
(3 Req'd) 3 N803952-S100 Washer 4 N808625-S100 Front Shock Absorber Nut 5 18183 Front Shock Absorber Mounting Bracket 6 3B455 Front Suspension Bearing and Seal 7 5310 Front Coil Spring 8 5414 Front Spring Insulator 9 18045 Front Shock Absorber A ? Tighten to 35-40 Nm
(25-30 Lb-Ft) B ? Tighten to 55-63 Nm
(40-46 Lb-Ft)
  1. ani_caut.gif CAUTION: Do not over tighten the lock nut; damage to the lock nut or piston rod could result.
    Install new rod lock nut and tighten it to 55-63 Nm (40-46 lb-ft).


f3897c.gif

  1. Remove the spring compressing tool.
  1. Position the strut assembly into the vehicle. Install the three mount-to-strut tower nuts. Tighten the nuts to 35-40 Nm (25-30 lb-ft).


f9154a.gif

  1. Partially raise the hoist.
  1. Position the strut assembly to the steering knuckle. Install the pinch bolt and tighten it to 115-132 Nm (85-97 lb-ft).
  1. Position the stabilizer link to the strut assembly and install the retaining nut. Tighten the nut to 90-100 Nm (66-74 lb-ft).


f8740a.gif

  1. Install the front wheel and tire assembly.
  1. Lower the vehicle.
hope this helps

Aug 14, 2011 | 1998 Ford Windstar

1 Answer

How to change a tie rod what.tools should be used


  1. Most tie rods consists of a Ball-Joint assembly. After removing the tire, you will need to pull the Tie-Rod Nut Retaining Pin before trying to take off the Tie-Rod Ball Joint Nut.
  2. After the Nut is removed, you can use a ball-joint separator to separate the ball-joint from the Hub assembly.
  3. After the Ball-joint is separated, mark the position of the old Tie-Rod where it connects to the Rack and Pinion assembly, and then remove the tie rod using a wrench.
  4. Installation is the reverse of disassembly.
  5. Once it is back together, you will need to get your vehicle aligned.

Mar 27, 2011 | Oldsmobile 98 Cars & Trucks

1 Answer

Front right hub and sensor assembly or a diagram


stevenhurc_11.jpg

Removal Steps

1. Torsion bar

2. Wheel speed sensor

(if equipped with ABS)

3. Back plate

4. Lower ball joint

5. Upper ball joint

6. Knuckle assembly

7. Oil seal

8. Thrust washer

9. Needle bearing

10. Knuckle

Installation Steps

10. Knuckle

9. Needle bearing

8. Thrust washer

7. Oil seal

6. Knuckle assembly

5. Upper ball joint

4. Lower ball joint

3. Back plate

2. Wheel speed sensor

(if equipped with ABS)

1. Torsion bar

Mar 01, 2011 | 1999 Isuzu Trooper

1 Answer

How to remove the right side axel shaft on a 98 olds bravada


1. Raise and support vehicle, then remove tire and wheel assembly. 2. Install a brass drift or a screwdriver to prevent the rotor from turning, Fig. 7 . 3. Remove axle nut and washer. 4. Remove stabilizer shaft or link from control arm. 5. Remove nut from ball joint, then separate ball joint from steering knuckle using separator tool No. J-36226, or equivalent. 6. Remove drive axle from hub and bearing assembly using front hub spindle remover tool No. J-28733-A, or equivalent, Fig. 8 . 7. Remove drive axle from transaxle using axle shaft remover puller tool Nos. J-33008, J-29794 and slide hammer tool No. J-2619-01, or equivalents, if necessary, Fig. 9 . INSTALLATION 1. Install drive axle into the transaxle using seal protector J-37292-B, or equivalent 2. Seat snap ring by placing a screwdriver into the groove on the joint housing and tapping until seated, Fig. 9 . 3. Grasp the inner housing and pull outward. If the snap ring is properly seated, the axle will remain in place. 4. Install drive axle into hub and bearing assembly. 5. Install lower ball joint to steering knuckle and tighten to specifications. 6. Install stabilizer shaft or link to control arm, tighten to specifications. 7. Insert a screwdriver or drift into caliper and rotor to prevent rotor from turning, Fig. 7 . 8. Install new hub nut and washer, tighten to specification. 9. Install tire and wheel assembly, then lower vehicle

Feb 13, 2011 | 1998 Oldsmobile Bravada

1 Answer

How long does it take to fix front bearings on a 97 dodge caravan? and cost


About an hour a side...This is the whole job and pictures....

The hub and wheel bearing unit is serviced as a complete assembly. Replacement of the front drive hub and bearing assembly can be done without having to remove the steering knuckle from the vehicle. However, if the hub/bearing assembly is frozen to the steering knuckle, removal of the steering knuckle is required.
  1. Disconnect the negative battery cable.
  2. Remove the cotter pin from the end of the stub axle. Remove the nut lock and spring washer. With the brakes applied, loosen, but do NOT remove the axle nut and washer with the vehicle still on the ground or damage to the wheel bearing will result.
  3. Raise and safely support the vehicle. Remove the wheel.
  4. Remove the front brake caliper assembly from the steering knuckle assembly and support from the strut assembly using a strong piece of wire.
    1. Remove the front brake rotor from the hub/bearing assembly.
    2. Remove the retaining nut and washer from the halfshaft stub axle.
    3. Remove the ABS wheel speed sensor from the steering knuckle.
    4. Remove the 4 hub and bearing assembly mounting bolts from behind the steering knuckle.
    5. Remove the hub and bearing assembly from the steering knuckle.
  5. To install:
    1. Thoroughly clean the mating surfaces of the steering knuckle and the hub and bearing assembly of any foreign material or nicks so the surfaces are clean and smooth.
    2. Install the new hub and bearing assembly and tighten the mounting bolts in a crisscross pattern to 45 ft. lbs. (65 Nm). Be sure the hub and bearing assembly is seated squarely against the front steering knuckle.
    3. Install the disc brake rotor.
    4. Install the brake caliper assembly onto the steering knuckle.
    5. Install the axle washer and nut. Tighten but do not torque.
    6. Install the ABS wheel speed sensor.
    7. Install the wheel and lug nuts. Torque the lug nuts, in sequence, to 95 ft. lbs. (129 Nm).
    8. Lower the vehicle. Do NOT roll the vehicle until the axle nut has been properly torqued or damage to the front wheel bearings will result.
    9. With the vehicle's brakes applied, torque the axle nut to 180 ft. lbs. (244 Nm). Install the spring washer, nut lock and a new cotter pin. Wrap the cotter pin prongs tightly around the axle nut lock.
    10. Reconnect the negative battery cable. Check the wheel alignment.

fe8edd6.gif
The hub/bearing assembly is attached to the steering knuckle with four bolts


9733319.gif
Removing a hub/bearing assembly



1867b08.gif
If the hub/bearing is "frozen" to the steering knuckle, separate the ball joint and lightly tap on the hub/bearing from behind



09233ac.gif
The hub/bearing assembly should free itself from the steering knuckle

About $60 a hub.

May 23, 2010 | 1997 Dodge Caravan

1 Answer

2002 ford explorer rear wheel bearing removal


Rear Wheel Bearing
REMOVAL AND INSTALLATION

1. Remove the wheel knuckle.

Wheel Knuckle
REMOVAL AND INSTALLATION

CAUTION: Do not loosen the axle wheel hub retainer until the wheel and tire are removed from the vehicle. Wheel bearing damage will occur if the wheel bearing is unloaded with the weight of the vehicle applied.

1. Remove the wheel and tire assembly.

NOTE: Have an assistant press the brake pedal to keep the axle from turning.

2. Remove the nut and washer and discard the nut.

3. Remove the parking brake shoes.

CAUTION: Do not damage the boot while separating the toe link from the knuckle.

4. Remove the nut and bolt and separate the toe link from the wheel knuckle and discard the nut.

CAUTION: Do not damage the boot while separating the ball joint from the knuckle.

5. Remove the nut and bolt and separate the upper ball joint from the wheel knuckle and discard the nut.

CAUTION: Do not use a hammer to separate the outboard CV joint from the hub. Damage to the threads and internal CV joint components may result.

6. Using the special tool, press the outboard CV joint until it is loose from the hub.

7. Remove the nut and bolt and the wheel knuckle, hub and bearing as an assembly and discard the nut.

(Return to)
Rear Wheel Bearing
REMOVAL AND INSTALLATION

2. Remove the three bolts.

CAUTION: Make sure that the press adapter outside diameter is slightly smaller than the hub outside diameter or damage to the knuckle will result.

3. Using a suitable press, remove the hub from the bearing and discard the hub.

NOTE: The retainer ring is tapered and must be installed flat side down.

4. Remove and Discard the retainer ring.

5. Using a suitable press, remove the bearing from the wheel knuckle and discard the bearing.

CAUTION: The hub and bearing cannot be reused after disassembly.
To install, reverse the removal procedure.

Jan 24, 2010 | 2002 Ford Explorer

1 Answer

Replacing a front wheel bearing


here is a step by step instructions on how to replace your bearing. please copy and paste the link into your browser for an image.

please do not forget to rate and comment about your experience with fixya today.

Removal & Installation
  1. Apply the brakes and hold in place.
  2. Raise the vehicle.
  3. Remove the front tire and wheel assembly.
  4. Remove the cotter pin, lock nut and spring washer from the hub nut.
  5. While the brakes are applied, loosen and remove the hub nut on the end of the driveshaft.
  6. Release the brakes.
  7. Remove the front disc brake caliper and adapter as an assembly, and the brake rotor from the steering knuckle.
  8. Remove the nut attaching the outer tie rod to the steering knuckle. To do this, hold the tie rod end stud with a wrench while loosening and removing the nut with a standard wrench or crowfoot wrench.
  9. Remove the tie rod end from the steering knuckle using Remover, Special Tool MB991113.
  10. Remove the tie rod heat shield.
  11. Remove the nut and pinch bolt clamping the ball joint stud to the steering knuckle.

    CAUTION The strut assembly-to-steering knuckle attaching bolts are serrated and must not be turned during removal. Hold the bolts stationary in the steering knuckles while removing the nuts, then tap the bolts out using a pin punch.
  12. Remove the two bolts attaching the strut to the steering knuckle.

    NOTE Use caution when separating the ball joint stud from the steering knuckle, so the ball joint seal does not get cut.
  13. Separate the ball joint stud from the steering knuckle by prying down on lower control arm and up against the ball joint boss on the steering knuckle.

    NOTE Do not allow the driveshaft to hang by the inner C/V joint; it must be supported to keep the joint from separating during this operation.
  14. Pull the steering knuckle off the driveshaft outer C/V joint splines and remove the steering knuckle.

    NOTE The cartridge type front wheel bearing used on this vehicle is not transferable to the replacement steering knuckle. If the replacement steering knuckle does not come with a wheel bearing, a new bearing must be installed in the steering knuckle. Installation of the new wheel bearing and hub must be done before installing the steering knuckle on the vehicle.
  15. If the wheel bearing and hub need removal. Do not reuse the wheel bearing.
    http://www.chiltonlibrary.com/content/images/32050/images/32050_ptcr_g0035.gif The separation of the ball joint and the knuckle
To install:
  1. Slide the hub of the steering knuckle onto the splines on the driveshaft C/V joint.
  2. Install the steering knuckle onto the ball joint stud aligning the bolt hole in the knuckle boss with the notch formed in the side of the ball joint stud.
  3. Install a new ball joint stud pinch bolt and nut. Tighten the nut to a torque of 70 ft. lbs. (95 Nm).

    CAUTION The strut assembly-to-steering knuckle attaching bolts are serrated and must not be turned during installation. Install the nuts while holding the bolts stationary in the steering knuckle.
  4. Position the lower end of the strut assembly in line with the upper end of the steering knuckle and align the mounting holes . Install the two attaching bolts. The bolts should be installed with so that the nuts face towards the front of the vehicle once installed. Install the nuts. Holding the bolts in place tighten the nuts to a torque of 40 ft. lbs. (53 Nm) plus an additional 90° turn after the specified torque is met.
  5. Place the tie rod heat shield on the steering knuckle arm so that the shield is positioned straight away from the steering gear and tie rod end once installed. Align the hole in the shield with the hole in the steering knuckle arm. Install the outer tie rod ball stud into the hole in the steering knuckle arm. Start the tie rod attaching nut onto the stud. Hold the tie rod end stud with a wrench while tightening the nut with a standard wrench or crowfoot wrench. To fully tighten the nut to specifications, use a crowfoot wrench on a torque wrench to turn the nut, and a wrench on the stud.
  6. Tighten the nut to a torque of 40 ft. lbs. (55 Nm). Install the brake rotor, disc brake caliper and adapter.
  7. Clean all foreign matter from the threads of the driveshaft outer C/V joint. Install the hub nut in the end of the driveshaft and snug it.
  8. Have a helper apply the brakes. With vehicle brakes applied to keep brake rotor and hub from turning, tighten the hub nut to a torque of 180 ft. lbs. (244 Nm)
  9. Install the spring washer, lock nut and cotter pin on the hub nut. Wrap the cotter pin ends tightly around the lock nut.
  10. Install the tire and wheel assembly. Install the wheel mounting nuts and tighten them to a torque of 100 ft. lbs. (135 Nm).
  11. Lower the vehicle.
  12. Set the front toe on the vehicle to required specification.

Apr 17, 2009 | 2003 Chrysler PT Cruiser

1 Answer

I am trying to get the wheel assembly apart to change the front bearings on a 1996 mercury villiger


http://groups.yahoo.com/group/villagerquest/

9ad2184.gif
Item Part Number Description 1 — Cotter Pin 2 — Nut Retainer 3 1131 Insulator 4 3B477 Front Axle Wheel Hub Retainer 5 1195 Front Wheel Outer Bearing Retainer Washer 6 1104 Wheel Hub 7 1107 Lug Bolt 8 3K050 Snap Ring 9 3123 Front Wheel Bearing 10 2K004 Front Disc Brake Rotor Shield 11 3130 Front Wheel Knuckle

Wheel Hub, Wheel Knuckle and Wheel Bearing SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Tie Rod End Separator T85M-3395-A
Removal
  1. Raise and support the vehicle.
  2. Remove the wheel (1007) and tire assembly.
  3. NOTE: It is not necessary to disconnect the front brake hose (2078).

    Remove the disc brake caliper (2B120) and suspend it with mechanic's wire out of the way. Refer to Section 06-03 for the removal procedure.
  4. Remove the front disc brake rotor (1125).
  5. Remove and discard the cotter pin.
  6. Remove the nut retainer and insulator.
  7. Remove the front axle wheel hub retainer (3B477) and the front wheel outer bearing retainer washer (1195).




  8. Remove and discard the cotter pin from the front suspension lower arm ball joint (3050).
  9. Loosen the front suspension lower arm ball joint nut until it contacts the front wheel driveshaft joint.


    stv~us~en~file=f8063b.gif~gen~ref.gif

  10. Strike the front wheel knuckle with a hammer while pulling down on the front suspension lower arm (3078) until the front suspension lower arm ball joint separates from the front wheel knuckle.




  11. Remove the front suspension lower arm ball joint nut.




  12. Remove the front suspension lower arm ball joint from the front wheel knuckle.
  13. Remove and discard the cotter pin.




  14. Remove the tie rod end nut.




  15. Use Tie Rod End Separator T85M-3395-A to separate the tie rod end (3A130) from the front wheel knuckle.




  16. Remove the front brake anti-lock sensor bolt.




  17. Remove the two front shock absorber-to-front wheel knuckle nuts.




  18. Remove the two front shock absorber-to-front wheel knuckle bolts.
  19. Remove the front shock absorber (18124) from the front wheel knuckle.
  20. Use 2-Jaw Puller D80L-1002-L, or equivalent, to separate the front wheel driveshaft and joint (3B436) from the front wheel knuckle.
  21. Remove the front wheel hub, front wheel knuckle and front wheel bearing as an assembly from the vehicle.
  22. If necessary, match mark and remove the steering stop bolt and steering stop bolt jam nut from the front wheel knuckle.




Installation
  1. Position the front wheel hub, front wheel knuckle and front wheel bearing as an assembly on the front wheel driveshaft and joint.
  1. Install the front wheel knuckle into the front shock absorber.
  1. Install the two front shock absorber-to-front wheel knuckle bolts.
  1. Install the two front shock absorber-to-front wheel knuckle nuts. Tighten the front shock absorber-to-front wheel knuckle nuts to 113-123 Nm (83-91 lb-ft).

Apr 10, 2009 | 1996 Mercury Villager

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...