Question about 1992 Oldsmobile Cutlass Ciera

2 Answers

Where is crank position sensor on 92 Oldsmobile 3.3 litre and how do I test it

Posted by on

  • Rob Bruce May 11, 2010

    Which Model Cutlass?

×

Ad

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 107 Answers

This censor is behind the harmonic balencer.. it has to be removed to change the censor hop this helps....

Posted on Jul 20, 2009

Ad
  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 14 Answers

Its located right behind the balancer. remove the balancer you will see the shield remove the shield and the sensor is located right behind it secured by a bracket.

Posted on Jul 20, 2009

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

emissionwiz
  • 76846 Answers

SOURCE: location of crank position sensor on 92 chevy corsica 3.1

You will have a no start or stalls after engine gets hot and then cools down restarts, the sensor is on the front of the engine mounted into the cam gear cover if it is not visiable get under the, (here is a picture) car and look.d37e0b9.jpg

Posted on Jan 21, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

97 Oldsmobile 88 after driving once motor is shut off will not crank until cool, had the control module tested it came back good, replace fuel pressure switch and still will not crank until cool?


You will need to replace the crank angle/position sensor near the crank pulley. A photo of the sensor is attached. The sensors wear out due to heat and cold cycles and internal corrosion.

MasterPro Ignition - Crankshaft Position Sensor Oreilly's Auto Parts part number is:
Line: MPI ' Part # 2-96054
96054-1_cranksensor-ssgfw3isdofovrvhx0ejjvhb-2-0.jpg

Feb 14, 2017 | 1997 Oldsmobile 88

2 Answers

97 oldsmobile achieva wont fire changed coil pack spark plugs cam sensor still wont start


Make sure battery has a full charge and battery connections all good.
If it cranks good but won't start, have a helper crank it while you visually check for spark at the spark plugs. If spark everywhere, use a gage and check proper fuel pressure and fuel injector pulse.
If you having a problem with more than one system, I want to check for rpm signal, that usually comes from the crank sensor. Not sure why you replaced cam sensor? I always want to check sensor wiring circuits before replacing anything. Don't replace anything unless your testing points in that direction.

Nov 04, 2016 | Oldsmobile Cars & Trucks

1 Answer

92 Oldsmobile cutlas cearia changed crank sensor spark module ( under ignition coils) and computer still no spark and no power to injectors tested all fuses the only thing that dont work is the dash lights...


Do a continuity check on the harness between the sensor and control module / visual check of it. There were problems during those years with chaffing.

Feb 09, 2015 | Oldsmobile Cars & Trucks

2 Answers

Car won't stay idling


throttle position sensor?

Dec 18, 2013 | Ford Probe Cars & Trucks

1 Answer

How do i replace the crank shaft position sencor on a 92 olds cutlass 2.3


CRANKSHAFT SENSOR LOCATED ON THE SIDE ENGINE BLOCK NEAR THE OIL PAN.JUST DISCONNECT ELECTRICAL CONNECTOR GOING TO SENSOR . AND REMOVE SMALL BOLT HOLDING IT IN PLACE THEN REMOVE SENSOR.

Jun 10, 2011 | Oldsmobile Cutlass Ciera Cars & Trucks

1 Answer

MY 92 OLDS 88 HAS NO SPARK.HAVE. HAVE POWER GOING TO ECM.HAS 3 COILS..FIGURE THEY ALL CANT GO OUT AT SAME TIME.REPLACED CRANKSHAFT POS. SENSOR AND HARMONIC BAL. 8 MONTHS BACK


Sounds like the ignition module or the crank sensor. Even though the crank sensor is fairly new doesn't mean anything. Remove the ignition module and take it to a parts store. Most parts stores can test it.

Jun 11, 2010 | 1992 Oldsmobile Eighty Eight

2 Answers

Not starting


i had the same problem with my 92 cherokee laredo, could be the crank positioning sensor. if it goes bad you dont get spark from the coil. or it could be the coil, distributor, or even spark plugs.

Mar 22, 2009 | 1992 Jeep Cherokee Sport

1 Answer

Location of crank position sensor on 92 chevy corsica 3.1


You will have a no start or stalls after engine gets hot and then cools down restarts, the sensor is on the front of the engine mounted into the cam gear cover if it is not visiable get under the, (here is a picture) car and look.d37e0b9.jpg

Jan 21, 2009 | 1988 Chevrolet Corsica

Not finding what you are looking for?
1992 Oldsmobile Cutlass Ciera Logo

Related Topics:

822 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8572 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...