Question about 1994 Dodge Viper

1 Answer

1994 viper clutch don' release clutch until 2" off floor

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Dodge Master
  • 2,615 Answers

Donald... hello,

Accordind to the ROCKAUTO Part listings (below)...

You have a HYDRAULIC clutch assembly
which should be needing more than a passing

My first suggestion would be to look at the master... add fluid as required... and look at both ends

I would call out the MASTER & SL... (subservient cylinder)...
but attempting to say slave in the past but it got OBSCURED.

Checking for leaks... if any are found... look to replacing both ends... they pretty much wear out together .

2 inches from the floor = TROUBLE 1994 DODGE VIPER 8 0L V10 Clutch Master Cylinder RockAuto

More Information for EXEDY MC424

Posted on Dec 11, 2016

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 566 Answers

SOURCE: 1997 hyandai accent gt clutch problem

hi considering age of car and that you have no leaks on hydraulics? may i suggest you try bleeding the clutch to rid of old fluid a couple of pumps may be suffice ? b/fluid does absorb moisture and heat over time hence recommendation tat fluid be changed at period specified in handbooks ie 12 monthly ?

Posted on May 15, 2009

  • 7353 Answers

SOURCE: How do you adjust the

a fabrication shop can make the pedal higher, even an inch makes a big difference. maybe add a piece that will be removable if you ever sell the car, so it can be returned to stock, without damaging the pedal.

Posted on Dec 05, 2010

Testimonial: "OK. That's a solution."

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Clutch pedal sinks to floor


Unless you have bled the slave cylinder properly there will still be air in it. However I think the problem is in the clutch master cylinder ---piston rubbers leaking fluid back to reservoir. Replace the m/cyl with new item and bleed out correctly.

Apr 27, 2013 | 1994 Toyota Tercel

2 Answers

My bro drained the clutch fluid out of his 1988 chevy s-10. and now the clutch hits the floor. how can we fix this???


bleed the system there is a tool required to do just that at your local auto partgs store.

Oct 18, 2011 | Cars & Trucks

1 Answer

How do you adjust the clutch pedal on a 1994 Dodge Viper for short people (5' 7") Inseam 30" I can depress it to the floor wtih the seat all the way forward, but it feels like a strech.


a fabrication shop can make the pedal higher, even an inch makes a big difference. maybe add a piece that will be removable if you ever sell the car, so it can be returned to stock, without damaging the pedal.

Dec 05, 2010 | 1994 Dodge Viper

1 Answer

Hard to get in reverse.grindes going in 2nd gear.


Is your clutch releasing very close to the floor? Too close to the floor usually indicates an air bubble in the clutch hydraulics or nearly out of fluid. Add fluid, check for leaks, and blead out air bubbles. Have you had the oil level in the trans checked? That should be done with every oil change. Add only perscribed fluid. Stop driving it until you get it fixed or you'll have one hellacious repair bill if you toast the tranny. Ray (garage owner)

Sep 20, 2010 | 1994 Saturn Sl

1 Answer

Have a 2004 jeep wrangler x with a manual transmission and when it is in nutral and the clutch out it rattles. Is this normal? i still have the factory warranty and went to a chrysler dealer and they tried...


A rattling noise from the transmission is never a normal condition no matter what anyone says, and the first thing to do is to check the transmission fluid level, but it sounds to me like the throw-out/release bearing is riding the clutch pressure plate, and when the clutch pedal is in the up position the throw-out/release bearing and the clutch pressure plate should not be touching each other, and the only time that they should make contact is to release the clutch disk in order to shift the transmission into gear. There should be about 1 to 2 inches of free play in the clutch pedal, and the clutch should start to grab within 1 to 2 inches of letting the clutch pedal up off of the floor, and if this is not the case you might need to have the clutch properly adjusted especially if the clutch does not start to grab until the clutch pedal is half way up from the floor. Also, the main bearing in the transmission could be going out due to low fluid, or a damaged pilot bearing that is allowing the transmission input shaft to wobble just enough to cause a rattle from the main bearing or even a vibration in the transmission.

Jun 02, 2010 | 2004 Jeep Wrangler

2 Answers

Need to bleed clutch to get peddle


try to vacuum bleed the system at the master most hand vacuum kit come with adapters to fit over the master reservoir otherwise the system may need a new master or you may have a leak

Sep 04, 2009 | 1994 Dodge Stealth

1 Answer

1997 hyandai accent gt clutch problem


hi considering age of car and that you have no leaks on hydraulics? may i suggest you try bleeding the clutch to rid of old fluid a couple of pumps may be suffice ? b/fluid does absorb moisture and heat over time hence recommendation tat fluid be changed at period specified in handbooks ie 12 monthly ?

May 15, 2009 | 1994 Hyundai Excel

2 Answers

Clutch goes to floor will not engage


The bleeder is located on the slave cylinder at the bell housing of the transmission. Follow the clutch pressure line down to the bell housing, and you will find the bleeder. To bleed the system properly, you will need to have someone push the clutch in, and hold it until you open the bleeder, and close it again. Repeat steps until you have a good solid clutch pedal. Make sure to not let the fluid level in the reservoir get too low as it can **** in air, and you have to start all over.

Mar 30, 2009 | 1994 Dodge Stealth

1 Answer

I replaced a hydrolic clutch on a 1988 prelude. I don,t know how to bleed the system. Help?????


you need 2 people, 1 with a spanner on the bleeder and the other to pump the clutch. fill the fluid canaster, pump the clutch, with the bleeder shut, then hold the clutch down then undo the bleeder, without releasing the clutch, allow the clutch to go to the floor air will come out, then tighten the bleeder, then you can release the clutch, keep repeating until you have a stream of fluid and no air, always make sure you have done up the bleeder before you release the clutch, and mke sure you have fluid in the canaster.

Aug 13, 2008 | 1988 Honda Prelude

Not finding what you are looking for?
1994 Dodge Viper Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...