Question about 2002 Suzuki XL-7

1 Answer

Replace front hub assembly 2002 Suzuki XL7 - 2002 Suzuki XL-7

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Suzuki Master
  • 20,706 Answers

The front wheel bearing hub?
XL-7 (the dash matters)
my wild guess, is the questions was
what are all steps to do this job. and tools.
that?
RTM?

https://suzukipitstopplus.com/Products/10056-2002-grand-vitara-xl-7-service-manual.aspx

http://www.fixkick.com/hubs/FW_BEARINGS.html#newer
the link shows all years, and variances.

here is a photo review, that is accurate up to
1998, and beyond , if you skip the bearing service parts. as yours are INTEGRATED
and NON-serviceable.
http://www.fixkick.com/hubs/FW_BEARINGS.html


the photo 6a and B
shows removing the hub,
so do that , buy a new hub and put it back
the same way, using the tool stated
at the stated ranges of torque
123-180 ft/lbs.
this range allows you to get the screws into the locking rings.

Posted on Dec 11, 2016

  • _-__-___-_
    _-__-___-_ Dec 12, 2016

    I sold all my suzuki dogs, when they went bankrupt here. (
    and that very special tool ($80) that fits that silly non standard, axle hub ring.
    (ie. GM truck tools do NOT FIT)
    it's a ring nut, and needs this tool.
    the bearings are crush type.
    unlike say your boat trailer...
    and if not set to the range of torque they will fail in under 3000miles says TIMKEN.
    they have hard proof, (life tests and facts)

    ring 19 is used, even on the newer cars,
    with integrated hubs, too. (facts)
    http://www.fixkick.com/hubs/4WD-89-91a.j...

    the matching tool is here

    here is that tool (NOT one sold in our brick auto stores, hard to find and buy them)
    http://www.fixkick.com/hubs/FW_BEARINGS....


    the torque is a range, as seen there.
    and the locking rig tabs only fit some holes.
    you can use the 2wd tool on the newer cars.
    the removal is the same as the photo sequences here,
    the only diff. is your hubs are fixed,
    they do not come apart,
    there are tiny 5mm screws that lock the ring

    I have the official SUZUKI parts page on my
    screen now, it has non servicable hubs
    and has the same locking ring. seen above.
    suzuki sells the hub with or without ABS

  • Anonymous Dec 12, 2016

    i had to buy a box of 5mm screws,
    as the old ones strip out, on removal
    they can.
    after long long service, or water ingress

×

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

techbuster
  • 5081 Answers

SOURCE: Torque specs on a 2006 chevy silverado front hub

The nut on the axelshaft is 177 ft. LBS.
The 4 bolts on the bearing hub is 133ft. LBS.

Posted on Sep 14, 2009

  • 205 Answers

SOURCE: 2002 saturn vue. replacing front bearings. I

have you un bolted the strut and disconnected the ball joint you have to do this to have room for the shaft to come out

Posted on Oct 15, 2009

Testimonial: "One oclock in the morning, im still working on this POS and he answers my question. Does your mechanic answer the phone at 1 a.m.? Thanks!"

  • 171 Answers

SOURCE: how to replace 2002 hyundai elantra hub and bearing

With the car on ground, break loose the drive-axle nut, and the wheel nuts , than jack up the car, support it properly, remove the wheel ,remove the axle-nut.
Remove the brake caliper assembly-- support it properly.
Remove the two bolts that hold the hub bracket to the Macpherson strut assemble, remove the lower arm ball joint and remove the steering tie- rod ball-joint attached to the hub bracket. That's it.Slide off the hub /with the bracket off the drive-shaft.
Follow steps backwards to assemble back.

Posted on Apr 09, 2010

Zeevert
  • 373 Answers

SOURCE: Replace front hub assembly....

Replacing the front wheel bearing/hubs can be a big job for the inexperianced. Briefly...
Remove tire/wheel
Remove brake caliper assembly, do not remove brake line.
Remove caliper bracket.
Remove brake rotor.
Unplug ABS sensor.
Remove the large axle nut.
Press axle out of bearing (may need special tool)
Remove the 3 bearing bolts and remove bearing.

Posted on Jun 11, 2010

  • 128 Answers

SOURCE: how to remove and replace front wheel hub assembly

Lift and SAFELY support the front of the vehicle.
Remove tire
Remove caliper bracket to steering knuckle bolts- larger and closer to the axle.
Use a wire or strap to support the caliper out of the way.
Remove the rotor
Remove the dust cap-( useless on these, but they put them there anyway)
Remove the axle nut- 36mm
Use a hammer and block of wood to make sure the axle is loose.
Remove the ABS wiring from the body
Remove the 3 15mm bolts from the back side of the knuckle.
Use the block of wood and hammer on the back of the hub flange to loosen the hub.
Remove hub
Clean the surface of rust,
Install new hub.
Here you can find the quality parts http://www.autopartspoint.com/products/wheel-hub-bearing.html

Posted on Aug 30, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Will a front differential out of a 2005 Suzuki xl7 work in a 2002 suzuki xl7


First sensible step will be to check the part numbers of both with the dealer parts department. If the numbers are the same there will be no problem.
If the numbers are different it won't mean the units won't interchange but then it will be down to measuring each and determining ratios or finding someone who has relevant model-specific experience.

Apr 19, 2015 | Suzuki XL7 Cars & Trucks

2 Answers

How do you replace rear wheel hub assembly on 2008 suzuki xl7?


hub? what is a hub? the axle? what is bad, post bad first then ask questions.
alldata.com

or the FSM
or
only, 4$ bucks to look

https://suzukipitstopplus.com/Products/1158-2008-xl7-service-manual.aspx

Jul 25, 2014 | 2007 Suzuki XL-7

1 Answer

Front wheel bearing on suzuki 03 xl7 4x4


old post.
and axles , really?
RTM

https://suzukipitstopplus.com/Products/1064-2005-forenza-reno-service-manual.aspx

$4 bucks to read the manual.
such a deal .

here is the GV , page. its same really
http://www.fixkick.com/hubs/vitara/new-vit-hubs.pdf

2001 + have the newer bearing hubs, unitized.
http://www.fixkick.com/hubs/no-crush.JPG


removing is easy, putting back right far harder.

see end hub #4
pull that with slide hammer, after removing screws #6
remove 7,8,9 and then using special tool pull ring 11.
with slide hammer pull, bearing hub.#1

RTM read the manual , at pitstop above
or the factory service manual , FSM
or at alldata.com,

Dec 31, 2013 | 2003 Suzuki XL-7

1 Answer

Replace fan belt on Suzuki XL7 2002


how do you get in to replace the belts? Do you have to remove the fan?

Oct 10, 2012 | 2003 Suzuki XL-7

1 Answer

How do I replace a turn signal bulb on suzuki xl7 2002


You have to take off the front grill and remove the head light assembly. It tells you how to do that in your owners manual. Contrary to some answers out there you DO NOT need to remove the radiator.

Jan 08, 2012 | 2002 Suzuki XL-7

1 Answer

How do we get the assembly apart to change out the parking light for a 2002 suzuki xl7


I have a suzuki XL7 and the heater will not blow hot air, it will blow warm air if the setting is on defrost but not otherwise.

Jul 03, 2011 | Suzuki XL7 Cars & Trucks

1 Answer

2003 SUZUKI XL7 2wd v6 \r\nRear wheel bearing making noise. How do you know for sure that is the problem and is bearings all i need I have ABS. How do I remove the bearing or the hub if that is what I...


remove the wheel and firmly hold the hub that encloses the wheel bearing. Now see if you can rock the hub
If so the bearing is bad
You will need to remove the braking system first to gain access to remove the hub assembly
the bolts are on the back side which is 3 of them

May 22, 2011 | 2003 Suzuki XL-7

1 Answer

2002 suzuki xl7 is throwing engine codes poo31 and p0446. The car is jerking really bad, often smells like fuel on the inside of the car, and sometimeswhen you try to put gas in it the gas spits back out...


PO-446 EVAP Vent Valve ( Cause of fueling issues & smell)

PO-31 O2 Sensor Bank 1 Sensor 1 ( Bad Heater)

Replace both front O2 Sensors

EGR Valve and or spark plugs (for Jerky)

Feb 20, 2011 | 2002 Suzuki XL-7

2 Answers

Replace front left wheel berring on 2002 GMC Yukon


do not replace only the bearing. replace hub assembly. remove rim/tire , remove caliper, mounting plate, rotor. . un bolt hub assembly, unplug abs. remove front axle nut if 4x4. you may need to rent the axle nut remove kit and hub puller. pull out hub. drive axle reward out of hub. install new part. do not torque hub over 90lbs. check with parts sell for spec

Jan 03, 2010 | 2002 GMC Yukon XL

Not finding what you are looking for?
2002 Suzuki XL-7 Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Boyet Soriano
Boyet Soriano

Level 2 Expert

293 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...