Question about 1998 Oldsmobile Aurora

Open Question

I need a free manual for a 98 oldsmobile aurora,doing a head gasket repair and engine timing is going to be an issue without a manual

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 883 Answers

SOURCE: 1997 oldsmobile aurora

rate me fixya!
2bbd775.jpg

Posted on Jul 11, 2008

SOURCE: need to know cylinder head bolt torque specs

Head Bolt Torque For your 1994 Oldsmobile Cutlass Supreme (3.4L SFI DOHC): clearpixel.gif Foot pounds (Final torque) clearpixel.gif Note: Torque sequence --------- | 6 2 3 7 | | 5 1 4 8 | --------- Step 1: torque in sequence to 33 Ft/Lbs Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque. clearpixel.gif clearpixel.gif clearpixel.gif Foot pounds (Final torque) clearpixel.gif Note: Torque sequence --------- | 8 4 1 5 | | 7 3 2 6 | front --------- of engine | 6 2 3 7 | | 5 1 4 8 | Step 1: torque to 40 Ft/Lbs --------- Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque.

Posted on Feb 07, 2009

  • 4088 Answers

SOURCE: causes for overheating in a 1997 oldsmobile aurora

Do the fan(s) come on when hot? Blow out the radiator core with compressed air (from the engine side) to clear it of bugs and other debris. Make sure the radiator is full to the top (when cold) and check the radiator cap seal rubber and the over-flow tank and tubing for leakage. It's possible that the water pump impeller is slipping on it's shaft and not pumping water properly. Remove the thermostat temporarily and remove the radiator cap. Remove some of the water so that the level is somewhat below the cap bottom, then start the engine and watch for rapidly moving water. That will show that the pump is moving water well. Allow the engine to heat up and keep track of the water movement. Shut the engine off at low end of 'normal' on the temp gauge and replace the cap so that it doesn't blow out boiling water into your face. Replace the thermostat and top up the water when cold again.

Posted on Sep 06, 2009

c17hydro
  • 2984 Answers

SOURCE: My 1998 Oldsmobile Aurora, is overheating!

You didn't mention replacing your water pump....that is what it is if you have NOT replaced it.

Posted on Oct 09, 2009

Testimonial: "Yes, I have bought the tool and pump to replace and after it is fix, I will contact you Thank you Tasha"

tecnovative
  • 360 Answers

SOURCE: Is there a way to

Yes, the head gaskets can be replaced without removing the engine.

If you will indicate which engine your Oldsmobile is equipped with, I will post the procedure.

Posted on Feb 21, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have a 1999 oldsmobile that keeps overheating i had the radiator the thermostat the water pump and top hose replaced not used but brand new a broken head gasket has been ruled out i need help asap


Check hand brake is fully released. Why head gasket had been ruled out ? Run engine till warm, carefully open rad cap, let engine idle, look for BUBBLES IN COOLANT. IF YOU SEE ANY NO MATTER HOW SMALL, CHANGE HEAD GASKET.

Oct 22, 2012 | 1997 Oldsmobile Aurora

1 Answer

Blown head gasket 2001 oldsmobile aurora


IF it was any gasket issue you would be losing coolant or getting air into the coolant, usually causing it to overflow. You have not said any of these things, so I would suspect this is an issue with the fluid not moving through the engine, either because it is blocked, or because the water pump is not moving it.

Nov 02, 2011 | 2001 Oldsmobile Aurora

1 Answer

I paid for a radiator, water pump, thermostat, and heater core to be put on my 2001 aurora and the engine is still bubbling I got an engine block test done and it was okay. Three Mechanics have tryed to...


does your cooling system hold pressure when it is hot? Is there the chance that either your surge tank or radiator cap is defective? It has to hold pressure when hot to function properly, and without a thermostat you will have issues with the car operating in open loop, causing damage to the engine and catalytic converter, not to mention possibly not getting heat in cold weather. You are aware that these engines (called 'shortstars') have issues with head gaskets-was it recently overheated. and is that why all this work was done? I have a 2001 Aurora with a 4.0, you have to watch the coolant level like a hawk on these engines (and on the 3.5, a sawed-off 4.0, I have one of them too, a 2000 Intrigue). If you are getting air pumped into the surge tank, you have a head gasket issue, or a cracked/warped head)-check your fluid level when the engine is cold, like after it sat overnight-fill it SLIGHTLY above the full cold mark, and start it, let it run with the coolant cap off until it gets to normal operation temp (half way up)-you may have a hard time getting it hot enough though, without the thermostat. Once at full operating temp. make certain the level is again SLIGHTLY above the full mark on the surge tank. If you are getting bubbles at this point, your block is not the issue, but the all too common head gasket(s) are-good luck, and if you get new head gaskets done, make certain you are using new bolts for the heads.

Mar 21, 2011 | 2001 Oldsmobile Aurora

1 Answer

I was told my cross over pipe gasket in my 98 aurora was leaking and that is the cause of my car over heating i was wondering if there was anybody that can give instructions on how to make the repair i am...


Take a good look at it. I believe this is a 4L engine, right? I had a similar issue on a 2001 Aurora, I believe same (or close) engine. I was told the cross-over was leaking and didn't want to get into it. (On the drivers side of the engine under the throttle body. You will see a big radiator hose connect to it. Well I left it go and the real issue was a leaking water pump bearing. It finally froze up on me and burned the belt and pulley driving it. The water pump replacement was not hard, just need a special tool to remove and replace. I rented one from Autozone. Anyway, I would start with the water pump and look at the gasket on the cross over to see if you can tell if it's really bad. Removing the air intake and throttle body helps getting to these parts.

Nov 18, 2010 | 1998 Oldsmobile Aurora

1 Answer

Hello, How much does it take to change an oil pan gasket on a 98 OLDSMOBILE AURORA v8 or cost?


theres more to it than a "gasket",the engine will need to come out and a complete reseal done. plan on $2000

Jun 27, 2010 | 1998 Oldsmobile Aurora

1 Answer

My car is over heating when im going down the hwy


May have head gasket leak. If so will be loosing water, possibly quite slowly. At highway speeds cylinder pressure is higher and so gasket leak more likely. Means gasket damage or loose cylinder head. Can be checked by mechanic. (pressure test and cylinder head bolt tension test)
Less likely alternatives, the spark timing is too advanced or the fuel too poor.

May 28, 2010 | 1998 Oldsmobile Aurora

1 Answer

Volkswagon polo p reg engine overheating and coolant leaking also heating is not working.


hi, its a good chance the head gasket has gone and also the thermostat will need checking and also the water pump.
if the water pump or the thermostat failed then this would cause the engine to over heat and blow the head gasket.

If your doing the work yourself then get a workshop manual as you will need it for the head bolt sequence and also the torque settings and timing marks for the timing belt.

Let me know how you get on or if you need further assistance ok

Feb 01, 2010 | 1998 Oldsmobile Aurora

1 Answer

98 aurora the dash instruments and engine control center DEAD


sounds like an open ground in the dash.run a wire from the dash metal framework to the negative battery terminal and see if it helps.

Oct 23, 2009 | 1998 Oldsmobile Aurora

4 Answers

Head gasket repair on the v 8 4.0 engine is it hard to do?


Very difficult, especially if you have never done one. This requires high precision tools and mechanical capabilities. You are advised to leave this one up to the professionals. Believe me, I still remember MY first headgasket and it drove me crazy back in 1969. Okay, yes, I'm getting old. Thanks, Dana.

Sep 30, 2009 | 1997 Oldsmobile Aurora

Not finding what you are looking for?
1998 Oldsmobile Aurora Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7688 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...