Question about Cars & Trucks

1 Answer

How do you fix error code U0151 in a 2014 Lancer?

I have a 2.4L engine. I don't know where to start.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that gotĀ 5 achievements.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

  • Contributor
  • 36 Answers

I'd start by rechecking the "MDS on" install to make sure all connectors near where you were working are well seated. also recheck where the previous harness would contact. i find it really hard to beleive that the old harness was too short. improperly routed perhaps, but too short???

U0154 - LOST COMMUNICATION WITH OCM (occupant classification module)

  • When Monitored:
  • With the ignition on
  • IOD fuse installed
  • FCM is configured correctly
  • Set Condition: Bus messages not received from the Occupant Classification Module for approximately 2 to 5 seconds.
Possible Causes
CAN B BUS CIRCUITS OPEN OR SHORTED
DTCS RELATED TO BATTERY VOLTAGE, IGNITION, OR VIN MESSAGES
FCM NOT CONFIGURED CORRECTLY
OCCUPANT CLASSIFICATION MODULE
OCCUPANT CLASSIFICATION MODULE POWER AND GROUND
MODULE THAT SET THIS DTC


OCM is located under passenger seat. make sure it's connector isn't loose.

Posted on Dec 10, 2016

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Mitsubishi lancer check engine light


yeah, if I were you, I will erase the fault code with your OBD2 car code scanner first. If the engine light on, there must have some questions on the throttle position sensor, I will fix it.

Dec 10, 2012 | 2008 Mitsubishi Lancer

3 Answers

My 2003 lancer over heated and won't start now.


too late, but the answer is: when the water system loses enough water, there is a sensor in the water inlet that tells the computer that there is no water, then the computer will not allow the engine to start, I check it on a radiator change I had to make a lancer 2006, we wanted to move the car a few meters but did not start because the hoses were not installed and the block had no water, so we had to start pouring water with a garden hose to the water inlet of the block and in that way started the engine.

Sep 16, 2011 | 2003 Mitsubishi Lancer

1 Answer

I installed a short ram air intake in my 2011 mitsubishi lancer es 2.0l and my engine didnt accept it its telling me my traction control is out and my rpm wont go over 4000 and its puting out a code that...


WOW! Don't even know what to guess on this one. I do have a suggestion though. Go to the manufactuers web site (of the short ram air intake) and see if they have a work around to make their product work with your car.

Jun 04, 2011 | 2011 Mitsubishi Lancer

1 Answer

Engine light came on after hard **** going up hill. Brought car to the dealer and they said nothing is wrong but these codes came up and now I'm wanting to know what these codes are


P1243 - Inquiry Response Error - try reading codes again.
P0725 - Engine Speed Circuit Sensor Malfunction. - VSS or wiring bad.
P0705 - Transmission Range Sensor Circuit malfunction (PRNDL Input) - Sensor or wiring bad.


Thanks for using FixYa - a FixYa rating is appreciated for answering your FREE question.

May 21, 2009 | 2008 Mitsubishi Lancer

1 Answer

Dodge ram50 1992 swap 2,4L to 2,6L


Greetings!

Yes, the engine mounts and bell housings are the same.
The swap should be straight forward, however be sure to swap all the vaccum controls and emission system from the 2.6L.

Have fun!
Cheers, Jay

Apr 29, 2009 | 1992 Dodge Power Ram 50

1 Answer

Dodge Caravan 2,4l 1997 timing belt change


you will need to change the belt tencioner aswell
if you havent don a cambelt before dont see youre local mechanic ok m8

Jan 03, 2009 | 1997 Dodge Grand Caravan

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

54 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...