Question about 1991 Buick LeSabre

2 Answers

Removal of read door panel 1991 buick lesabre

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Buick Master
  • 13,505 Answers

Posted on Dec 10, 2016

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Buick Master
  • 48,532 Answers

Not supposed to remove them ever

Posted on Dec 10, 2016

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

Tip

How To Install Remove Rear Door Panel 1st Design Buick LeSabre 00-05 1AAuto.com


How To Install Remove Rear Door Panel 1st Design Buick LeSabre 00-05 1AAuto.com

on May 03, 2012 | 2002 Buick LeSabre

Tip

How To Remove Door Panel 1st Design Buick Lesabre 2000-05 1AAuto.com


How To Remove Door Panel 1st Design Buick Lesabre 2000-05 1AAuto.com

on May 02, 2012 | 2000 Buick LeSabre

1 Answer

Backdoor is unlocked on passenger side, but wont open


Sounds like you have a rusted door lock in that door, inside panel will have to be removed to access the lock assembly!

Mar 17, 2014 | 1991 Buick LeSabre

2 Answers

Locate fuel filter for a 1991 buick lesabre limited


fuel filter should be in the tank with the fuel pump.

Jan 04, 2010 | 1991 Buick LeSabre

1 Answer

Removal of the stereo of a Buick LeSabre. what part of the dash do i need to remove and how?


the trim around the heater controls snaps in, its black. Remove it and remove the four screws on the woodgrain panel. Lift off to acess radio.

Nov 22, 2009 | 1991 Buick LeSabre

1 Answer

94 LeSabre inner door panel removal


On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls

Apr 22, 2009 | 1994 Buick LeSabre

1 Answer

Buick LeSabre left front window will not close


Don it. Good half day for amateur. Get Chilton 86-99 Bonneville, 88, Lesabre manuel.. Tricky to find bolts are under end flaps on door close handgrips. Took me a day to figure that one out. Others under light at lip of back of door. Book indicates to strart with window 3/4 up if you can. Flip up window control at rear of panel. After all screws are out raise outer edge of armrest and look for notches 4" and 11-1/2" from rear of armrest to slide inward to remove. There are screws under the door handle too. Screws everwhere. When pulling bottom of panel from door lift with a notched bar to avoid tearing the fasteners out of the cardboard panel. Two screws behind seatbelt notch at top need to come out to allow positioning the glass. The panel at the bottom of the top opening can be removed for more fredom in positioning the glass when reinserting the ball in the lower track on the window. Tape glass with duct tape to keep it from falling. Drill the factory rivets that hold the old regulator and I replaced with stove bolts with nylon locknuts slotted head to the inside the car. Can't remember the size, probably 1/4 or 3/16". Remove speaker if in front bottom of door to use your hand to do work in the door. You must twist the regulator forward with window 1/2 down to remove the ball from the socket in the bottom sliding metal track at the bottom of the window. Don't drop the window after removing the socket, tape it in place. Don't know what you do if you cannot move it to 1/2 up position. By the way, the body shops say you must use rivets, not screws or it will shift, but I have had no problems with the screws for reinstallation several years old. The rivet they use take a big hydraulic pop rivet gun that you won't have. Good luck, I don't envy you. Need to do other window on my 91. The window control may not be the same on the Custom, mine is the Ltd. you may be able to remove the motor from the regulator in the door without removing the regulator if you can figure out how to get the bolts that hold the moter to the regulator. inside the door.

Dec 19, 2008 | 1991 Buick LeSabre

1 Answer

Ihave no heat on my 1991 buick lesabre


A device called the "blend door" may be inoperable; this is located in the heater exchange box on the firewall...accordianman

Dec 15, 2008 | 1991 Buick LeSabre

Not finding what you are looking for?
1991 Buick LeSabre Logo

Related Topics:

33 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...