Question about 1985 Ford F150

2 Answers

Where is the inertia switch located

Thats all for now in the middle of motor swap

Posted by on


2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • Master
  • 834 Answers

If it is not found behind the passenger side kick-panel, then check under the dash, below the heater case, and behind the carpet on the passenger side. Here are diagrams to assist you.where is the inertia switch located - 6658478.jpg


Posted on Jun 24, 2010

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.


    An expert whose answer got voted for 20 times.


    An expert who has answered 20 questions.

  • Expert
  • 56 Answers

It is under the glove box on the passenger side wall in fornt of the door hinge.

Posted on Jul 21, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

Do I have to have the brain relearned after swapping out motors.

If everything on both engines were the same, no reprogramming should be required. The engine should start, and it may take a few minutes for the engine to run smoothly since there are going to be some differences in the way the "new" engine performs. I would guess that there is some connection to the engine that is loose or missing. You said it has fuel and fire. The only other thing needed is air. And unless you are in a vacuum, it should start.

Nov 02, 2015 | Dodge Cars & Trucks

1 Answer

2001 dodge ram 5.2 motor swapped out of a 1996 dodge ram turns but don't start

Is it possible that you did not swap the ECM module along with the engine

May 31, 2015 | Dodge Ram Cars & Trucks

1 Answer

Swapped motor miss fires throught throttle

Why motor swap?

Used motor went in,I don't ever like that senerio

Junk out --junk in

Explain the thru throttle part

Explain in detail what has been tested,how & the results

Dec 10, 2012 | 1999 Mercury Mountaineer

1 Answer

Can I put a 1981 ford f-150 motor in a 1991 ford f-150 truck

Sounds to me like you opened a can of worms that you are not equipped/qualified to deal with. To begin with, doing an engine change the way you did it is illegal. It is OK to put the newer motor in the older vehicle, but it is against federal law to put the older engine into the newer vehicle. REFERENCE: EPA ENGINE SWAP FACT SHEET

With all that said, if you want to do a swap like that, it is necessary to also swap wiring harnesses and computer modules (among several other components) if you expect it to work.

Mar 17, 2012 | 1991 Ford F150

1 Answer

My driver's side power seat works going up and down but it only moves 1" forward and backward about in the middle of the track. What could be the problem?

it is 17 years old, and like all electric motors, it is worn out. pull the seat out and take a long look at the mechanism on the bottom, then start cruising junkyards until you find one like it. buy it and swap it in, most likely any 90s ford power seat will have about the same electricals.

Mar 08, 2011 | 1994 Ford Mustang

1 Answer

I cant locate the fuse for my fan to cool the engine in my 1997 chrysler concorde

Look for the Fan Relay on the engine compartment fuse box, I think is on the Driver's side by the fenderwell. To test it, swap it with the AC Relay or another one with same relay number. The Fan should come on when the niddle is about the middle OR if you turn the AC on, the fan should start inmediately.

I have an 99 Intrepid and I had to replace the fan motor last year, the motor's bearings got dry and it was a little hard to turn. With engine OFF, turn the fan by hand and see if it keep turning, if it does not turn at least once, replace motor.

Good Luck!! Don't forget to rate this post!!

Sep 03, 2010 | Chrysler Concorde Cars & Trucks

1 Answer

I have a 1993 Honda Civic EX (2dr) which continues 2 overheat! The radiator has been replaced 3 times. The 1st time it had a hole, 2nd time it was determined that it leaked @ the seams when a pressure test...

any motor swap? have a block test done to check for the headgasket... it's possible you have warped the head with the list of cooling issues you have had.

Aug 06, 2010 | 1993 Honda Civic 4 Door

1 Answer

Looking to do a motor swap in a 98 sunfire...what motors fit?

It is true, you can only put another 98 2.2 liter in it. They did come with a 2.4 liter but you have to swap the motor, transmission, wiring harness, computer, and God knows what else. I would go with the 2.2 liter and check into some performance aftermarket parts for the 2.2, computer chip, performance exhaust and so on, somewhere like Summit Racing.

May 23, 2010 | 1997 Pontiac Sunfire

2 Answers

1999 bonneville blower motor not working all the time

I had similar problem, it would cut out in the middle of driving, I replaced the blower motor and it has been fine ever since, It was pretty easy to swap out.

Apr 10, 2009 | 1999 Pontiac Bonneville

Not finding what you are looking for?
Cars & Trucks Logo

798 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

79847 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers


Level 3 Expert

5685 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides