Question about Ford Cars & Trucks

1 Answer

Will a TPS sensor and MAP sensor work off an 1993 ford esort 1.9 motor

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 1,334 Answers

If part numbers match yes

Posted on Dec 10, 2016

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Will any ford TPS and MAP sensors work in 1993 probe gt 5 speed


All depends on if that part is designed to function on those vehicles. Go to a parts store or on line and look for those components for those cars. Compare part numbers, if they match then you're ok.

Dec 10, 2016 | Ford Cars & Trucks

1 Answer

How to idol down a 4.3 v 6 throttle body motor in a 1993 chevy astro mini van.


Sometimes a car idles high because the mass airflow sensor doesnt work and then the throttle sensor assumes a default position of wide open. Maf, Map, and tps are connected.

Nov 05, 2012 | Cars & Trucks

1 Answer

1993 ford f350 with 7.5 liter gas sticking on high idle i changed the tps and map sensors and new vacuum lines


check your idle air controller, they usually get a heavy carbon buildup on them and stick-easy to remove and clean.

Oct 04, 2011 | 1993 Ford F350

1 Answer

Is the module and/or solenoids inside of the transmission or outside of the transmission on a 1993 ford F250?


The transmission control module is part of the engine controller in the firewall behind left fenderwell.There is a solenoid block inside the Transmission pan that contains 5 solenoids , 2 shift,1 coast , 1 tcc and 1 pressure control.Various engine sensors also input into the transmission controller such as TPS ( throttle position sensor ) , map/mass ( engine load ) , and engine rpm.Also there is a trans temp sensor built into solenoid block and a range sensor on the side of trans that tells the computer where there gear selector is.Vehicle speed sensor also inputs into transmission controller.It takes a lot of data to decide what gear the transmission should be in.

Feb 25, 2011 | Ford F-250 Cars & Trucks

1 Answer

1993 pontiac grand am 3800 v6.codes 22,31,and 34.engine dies and sometimes won't restart for awhile....why? any help would be greatly appreicated,thanks


22 is tps sensor signal low--31 is cam sensor fault---34 is map sensor signal out of range. have a great day!!

Oct 18, 2010 | 1993 Pontiac Grand Am

1 Answer

Location of tps and map sensor on a 02 jeep grand cherokee 4.7l


Both are attached to the throttle body. Tps is on the other end of the throttle plate shaft opposite the linkage, MAP is on the side...has small vacuum hose underneath and is flat, about 3" long. The other item on the TB is the idle air motor, next to tps.

May 07, 2010 | 2002 Jeep Grand Cherokee

2 Answers

1993 Lexus Ls400 loss of power at 2500-3000rpm


Check your MAF and MAP sensor. The first 80% of your throttle signal from the TPS works with the O2 sensor to try to keep the air fuel ratio to 14.7 to 1 with the ECM controlling the fuel injector spray time and timing the ignition. After the 80% to WOT the ECM puts the O2 sensor in to an open loop and takes the Reading form the MAF and MAP sensor to run the engine richer so there will not be any Detonation to the engine and burning holes in the valves for running too lean. That is why it always feel like you get a little more when you ease off on the gas peddle from WOT. Recap check the TPS, MAF,and MAP sensor and wires to those sensors, if you can get the car scanned that would be great and you may find out which sensor may have gone bad, the other thing to is the fuel pressure regulator may be going bad and at WOT the pressure may be to high causing it to run to rich causing the loss of power. Good luck and hope this helps. 

Jul 04, 2009 | 1991 Lexus LS 400

1 Answer

93 ford probe kills when i let off the gas, is starts up fine ,after it warm up it kills


Most likely the TPS (Throttle Position Sensor) which controls cold, warm, and AC on idling speeds. Another cause could be the MAP sensor but I'd lean toward the TPS. Best of luck.
Greg

p.s. You can bring the car to a service station or auto parts store which features free diagnostic testing which will give you any error codes to lead you in the right direction.

Jul 04, 2009 | 1993 Ford Probe

2 Answers

What is check engine codes 24 and 33?


Code 24 is a defective speed sensor, usually located on the side of the tranny.
Code 33 is a defective map sensor, under hood located in one of many places. It's a black plastic square in shape box, has a wire connection and a vaccum hose connected to it.

Apr 08, 2009 | 1993 Oldsmobile Cutlass Supreme

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5481 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...