Question about Cars & Trucks

Open Question

Need scmetic for hw1210lr heat section, how do you remove for service

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you replace the evaporator for the a/c on a 2000 jimmy? What do you have to remove to "get" at it???


This is a pretty major job. The standard labor time to complete this task for an experienced technician with all of the correct tools and equipment is 6.2 hours.

Here are the steps from the service manual:

CAUTION: Perfom refrigerant recovery and verify A/C system pressure is at or below 0 in.Hg. before proceeding.
failure to do so can result in personal injury.

Disconnect the underhood lamp electrical connector, if equipped.
Remove the hood.
Remove the VCM or the PCM.
Remove the coolant recovery tank.
Disconnect the electrical connectors from the grille mounted lamps if equipped.
Remove the right front headlamp assembly.
Remove the front bumper.
Remove the right wheelhouse panel.
Disconnect the radio antenna cable.
Disconnect the electrical connector for the horn.
Remove the right fender.
Remove the blower motor resistor.
Remove the accumulator.
Remove the evaporator tube.
Remove the evaporator and blower module heat shield mounting screws (Utility).
Remove the evaporator and blower module heat shield (Utility).
IMPORTANT: Retain the evaporator and blower module heat shield mounting bracket for installation (Utility).
Remove the evaporator and blower module mounting bolts and nuts.
Remove the evaporator and blower module from the vehicle.
Remove the six evaporator case section to the blower case section retaining screws.
Separate the evaporator case section from the blower case section.
Remove the evaporator core from the blower case section.

Aug 27, 2011 | 2000 GMC Jimmy

1 Answer

How do you drop the exhaust system to pull the oil pan 0n a 1997 Ford 2 liter Escort


Section 309-00: Exhaust Components - General Information 1997 Escort, Tracer Workshop Manual REMOVAL AND INSTALLATION Three Way Catalytic Converter (TWC) Removal
  1. svf~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: When servicing the exhaust system or removing exhaust components, disconnect the heated oxygen sensors at the wiring harness to prevent damage to the sensors and harness.
    Disconnect the heated oxygen sensor (HO2S) electrical connectors.
  1. Remove the (A) five nuts and remove the (B) exhaust manifold heat shield.
  1. Remove the four exhaust manifold to three way catalytic converter (TWC) nuts.
  1. Raise and support the vehicle; refer to Section 100-02 .
  1. Disconnect the downstream HO2S and position it aside.
  1. Remove the two TWC bracket bolts.
  1. Remove the two (A) TWC to muffler inlet pipe bolts and nuts and the (B) TWC. Discard the gasket.

Jun 06, 2011 | Ford Escort Cars & Trucks

3 Answers

Where Is The Fuel Filter Located On A 2003 Ford Explorer V8 And How Do You Change It?


  1. Disconnect the battery ground cable.
  2. Properly relieve the fuel system pressure.
  3. Raise the vehicle on a hoist.
  4. Remove the bolts and the fuel filter heat shield.
  5. Remove the nuts and the fuel filter shield.
  6. Disconnect the quick release and spring lock couplings and remove the fuel filter.

To install:
  1. Remove any fuel line caps.
  2. Install the new fuel filter, connecting the quick-release and spring-lock couplings.
  3. Install the fuel filter shield.
  4. Install the fuel filter heat shield. Torque the bolts to 15 ft. lbs. (20 Nm).
  5. Reconnect the battery ground cable.
  6. Lower the vehicle.
  7. Start the vehicle, check for leaks and repair if necessary.


e38232f.jpg

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

Mar 26, 2010 | 2003 Ford Explorer Sport

1 Answer

Cannot find a maintenance manual any where for a 2006 Madza 3. I need to know where the spark plugs are at


For Mazda Car 2005-06 Spark Plugs...

Inspection
Inspect the electrodes and ceramic insulator.Burned or worn electrodes may be caused by:

Advanced ignition timing Loose spark plug Plug heat range too hot Insufficient cooling
Fouled plug may be caused by:
Retarded ignition timing Oil in combustion chamber Incorrect spark plug gap
Plug heat range too cold Excessive idling/low speed running Clogged air cleaner element Deteriorated ignition coils
Do not adjust the gap of platinum tip plugs; replace the spark plug if the gap is out of specification. The gap should be 0.049-0.053 in. on all models except Mazdaspeed6 or 0.028-0.031 on Mazdaspeed6 models.
  1. Replace the plug at the specified interval or if the center electrode is rounded.
  2. Apply a small quantity of anti-seize compound to the plug threads, and screw the plugs into the cylinder head finger-tight.
Removal & Installation
  1. Before servicing the vehicle, refer to the precautions section.
  2. Remove the battery cover.
  3. Disconnect the negative battery cable.
  4. Remove the plug hole plate by lifting off and removing the plug hole plate from the installation areas (rubber and clips) as shown in the illustration.
  5. Remove the front suspension tower bar (joint).
  6. Remove the ignition coils.
  7. Remove the spark plugs.

To install:
  1. Installation is the reverse of removal, tighten the plugs to 8-10 ft. lbs. (10-14 Nm).
2.3L (L3) Engine
  1. Before servicing the vehicle, refer to the precautions section.
  2. Disconnect the negative battery cable.
  3. Remove the ignition coils.
  4. Remove the spark plugs.

To install:
  1. Installation is the reverse of removal, tighten the plugs to 8-10 ft. lbs. (10-14 Nm).

Mazdaspeed6
  1. Before servicing the vehicle, refer to the precautions section.
  2. Disconnect the negative battery cable.
  3. If equipped with a turbocharger, remove the charge air cooler.
  4. Remove the ignition coils.
  5. Remove the spark plugs.

To install:
  1. Installation is the reverse of removal, tighten the plugs to 79-177 inch lbs. (9-20 Nm).

Good luck(remember rated and comment this help).

Mar 07, 2010 | 2006 Mazda 3

1 Answer

Heater core


You need review details in the Service Section-24-Heating-Air-Conditioning and Section-24a-Heating-Air-Conditioning

Hope helped with this (remember rated this help). Good luck.

Nov 12, 2009 | Jeep Cars & Trucks

1 Answer

Oxygen sensor


you need to borrow the oxygen sensor wrench from autozone or whereever you bought the sensor. Section 03-14: Engine Controls, Electronic 1996 Taurus, Sable Workshop Manual REMOVAL AND INSTALLATION -------------------------------------------------------------------------------- Heated Oxygen Sensor (HO2S) SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Oxygen Sensor Wrench T94P-9472-A Removal and Installation Disconnect battery ground cable (14301). Refer to Section 14-01 . On 3.0L (4V) engine remove cowl extension and right side of leaf screen. Disconnect engine control sensor wiring (12A581) from heated oxygen sensors (HO2S) (9F472). Do not remove harness connectors from the brackets. Raise vehicle on hoist. Refer to Section 00-02 . NOTE: If excessive force is needed to remove a heated oxygen sensor, lubricate the heated oxygen sensor with penetrating oil prior to removal. Remove heated oxygen sensors from exhaust manifolds (9430) using Oxygen Sensor Wrench T94P-9472-A. To install, reverse Removal procedure. Apply a coating of anti-sieze compound to threads of heated oxygen sensor. Tighten heated oxygen sensors to 34-46 Nm (26-34 lb-ft).

Jun 13, 2009 | 1996 Ford Taurus

1 Answer

How do you replace the oxygen sensors on a 1995 merc sable with a 3.0 ltr motor


they just unscrew from the exhaust pipe.

Heated Oxygen Sensor (HO2S) SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Oxygen Sensor Wrench T94P-9472-A
Removal and Installation
  1. Disconnect battery ground cable (14301). Refer to Section 14-01 .
  1. On 3.0L (4V) engine remove cowl extension and right side of leaf screen.
  1. Disconnect engine control sensor wiring (12A581) from heated oxygen sensors (HO2S) (9F472). Do not remove harness connectors from the brackets.
  1. Raise vehicle on hoist. Refer to Section 00-02 .
  1. NOTE: If excessive force is needed to remove a heated oxygen sensor, lubricate the heated oxygen sensor with penetrating oil prior to removal.

    Remove heated oxygen sensors from exhaust manifolds (9430) using Oxygen Sensor Wrench T94P-9472-A.
  1. To install, reverse Removal procedure. Apply a coating of anti-sieze compound to threads of heated oxygen sensor. Tighten heated oxygen sensors to 34-46 Nm (26-34 lb-ft).


    Heated Oxygen Sensors—3.0L (4V) Engine


4da449b.gif

May 02, 2009 | 1995 Mercury Sable

1 Answer

Where's my O2 sensor located


Heated Oxygen Sensor (HO2S) SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Oxygen Sensor Wrench T94L-9472-A
Removal and Installation
NOTE: If excessive force is needed to remove heated oxygen sensor (HO2S) (9F472) , lubricate heated oxygen sensor with penetrating oil prior to removal.
  1. Disconnect battery ground cable (14301) .
  1. Disconnect heated oxygen sensors from engine control sensor wiring (12A581) .
  1. Raise vehicle on hoist. Refer to Section 00-02 .
  1. Remove heated oxygen sensors from dual converter Y pipe (5F250) using Oxygen Sensor Wrench T94L-9472-A.
  1. To install, reverse Removal procedure. Tighten heated oxygen sensors to 36-46 Nm (26-34 lb-ft).

980db4e.gif

Feb 22, 2009 | 1994 Ford Thunderbird

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...