Question about 1989 GMC S-15 Jimmy

Open Question

Where is fuse panel for windshield wipers on a 1989 GMC S15 pickup truck

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 56 Answers

SOURCE: 1989 GMC Sierra truck doors loose

Hey there.You can purchase a door pin and bushing repair kit to tighten up the hinge area,requires removing the door to replace.If the hinge area is worn to badly,the brass bushings willnot last.Also your window crank handle is held on by a C-clip behind the handle in between the plastic shim and the handle which requires a special tool to remove or a small screwdriver to get the clip off.It is hard to see.The shaft that the handle is on are known to wear also and if thats the case you will need to have the window regulator replaced.Hope this helps.John.

Posted on Mar 10, 2009

  • 290 Answers

SOURCE: windshield wiper

I just take the arm off and reposition the arm in the splined shaft.

Posted on Jun 10, 2009

  • 89 Answers

SOURCE: looking for diagram of the fuse box for a 1984 gmc

dont realy need aq digram, open fuse box check each fuse with a test lamp when you get to the one that does not vlighht up chan ge it. berrydalewolf

Posted on Oct 29, 2009

  • 432 Answers

SOURCE: 1990 GMC Sierra 1500 pickup. Windshield wipers, Cruise Control

May want to look at replacing the wiper circuit board.It is located on the firewall adjacent to the wiper motor and has a some what square black cover with 3 torx screws and wireing harness pluged into the side.We had a truck that every time you washed it the wipers would stay on until it dryed out.You can try removing it and spaying it down with contact cleaner just watch the brease on the two contact tips.Well hope this helps.

Posted on Feb 05, 2010

  • 12 Answers

SOURCE: windshield wipers in my 1989 gmc sierra k1500 only

If you raise your hood and look at your wiper motor on the fire wall there is ablack plastic cover over the motor remove that and you will see a chip board that is replacable its usually around $20 or so, which is cheap way to find out if your wiper switch or multifunction switch is bad, since they arwe far more expensive! if the board does not solve your problem then suspect multifunction switch!

Posted on Mar 29, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is fuse for. GMC Acadia windshield wiper


You did not give the year, but it should be a 25amp fuse or circuit breaker in the panel inside the passenger compartment.
Check your owners manual for details.

Oct 21, 2014 | GMC Acadia Cars & Trucks

1 Answer

1989 dodge pickup fuse box location for windshield wipers locatio-n


If it uses a fuse it should be in the box under the speedometer or in the glove box. Some models use a circuit breaker.

Jan 19, 2013 | Cars & Trucks

1 Answer

1989 gmc s15 starts then dies


you need to check the battery cables and clean them and clean them, or it could be the coil needs replaceing or there might be a fuse blowed somewhere.

Mar 17, 2012 | GMC S-15 Cars & Trucks

1 Answer

Where is the wiper motor on my 1999 GMC Yukon?


Windshield Wiper Motor
Removal & Installation
To Remove:


  1. Remove wiper arms.
  2. Remove weatherstrip from cowl.
  3. Remove two cowl vent grille panel screws.
  4. Remove windshield nozzles and hoses.
  5. Remove three cowl vent grille panels.
  6. Disconnect windshield wiper motor electrical connector.
    NOTE: Do not remove crank arm from windshield wiper motor.

  7. Loosen nuts that attach the drive link brackets to the crank arm.
  8. Remove wiper motor crank arm brackets.






    gm-06-00-1079.gif



  9. Remove three bolts and windshield wiper motor from vehicle.

To Install:


  1. Install windshield wiper motor and three bolts.

    • Torque to: 62 in lbs. (7 Nm)

  2. With right side linkage closest to the windshield wiper motor, install drive
    link brackets to wiper motor crank arm.

    • Torque nuts to: 44 in lbs. (5 Nm)

  3. Connect electrical connector.
  4. Install nozzles and windshield washer hoses to cowl vent grille.
  5. Install three cowl vent grille panels and screws to vehicle.
  6. Install weatherstrip to cowl.
  7. Install wiper arms.


prev.gif next.gif

Oct 30, 2010 | 1999 GMC Yukon

2 Answers

1990 GMC Sierra 1500 pickup. Windshield wipers, Cruise Control


May want to look at replacing the wiper circuit board.It is located on the firewall adjacent to the wiper motor and has a some what square black cover with 3 torx screws and wireing harness pluged into the side.We had a truck that every time you washed it the wipers would stay on until it dryed out.You can try removing it and spaying it down with contact cleaner just watch the brease on the two contact tips.Well hope this helps.

Feb 05, 2010 | 1990 GMC Sierra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...