Question about Cars & Trucks

1 Answer

What does it mean when i see STOP and LOSS OF PERFOMANCE on a midlum 150

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 75,051 Answers

It means that a serious fault has occurred, and you need a service tech to look into it.

Posted on Dec 09, 2016

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Looking for a sump pan for a Midlum 150


Depends a bit where you are. In many locations wreckers maintain a parts query website, to which they all subscribe. You place a query, and any wrecker with the part will email you, eg

http://www.partshotlines.com/

Look for these websites. Also eBay lists one or two of these vehicles but the seller nay not want to separate the pan from the engine,

If it is dented and gashed you can have it welded OK.
.

Sep 09, 2016 | Renault Cars & Trucks

1 Answer

Code 00016407126,renault midlum 7t..2003..what does it mean..the truck is not pulling after changing filterd


that code should be in your owner manual. If it not Auto zone will have a book on your car Haynes manuals they have a code section. Buy the manual is $30.00

Aug 02, 2016 | Cars & Trucks

1 Answer

2004. Why did it lose acceleration?


run the fault codes and check for transmission control, servo, solenoid problems

Oct 11, 2015 | Ford F-150 Cars & Trucks

1 Answer

96 ford f-150, well that was the first problem. I continued to drive it with overdrive turned off. Then it got so it surges when you stop at a light and it's in gear. You have to rev it up a little to...


What was the first problem ??
If you have a trouble code for the idle air bypass valve, it means the valve is not working, not that the valve is defective. You could have a dirty throttle body or sludge in the port for the valve. The computer uses the valve to control air entering the intake to regulate idle speed.

May 10, 2013 | Cars & Trucks

1 Answer

Its showing code P2118, Throttle actuator control motor current range perfomance


Thankyou folks for the great answer, i did a OBD scan and based on the code i came to this site, with a $5 fuse i was able to get my life back.
the dealership quoited me $150 for diagnostics and parts additional.

Oct 09, 2012 | 2007 Toyota Camry

1 Answer

Runs terrible misses loss of power and reading p0174 code.


P0174 means that you have to much oxygen in the exaust system. When your car is running your computer sets the air/fuel mixture for you to run at its best perfomance. Most causes for this propblems are; 1. MAF Mass Air Flow Sensor. 2. worn out/dry rotted/ leaky vacuum lines 3. posible EGR vavle but not real common & 4. low fuel pressue. You can clean the MAF with electrical parts cleaner but don't touch the wires and stuff and I would only use elecrical parts cleaner. It should be located in the air duct. Next I would check all my vaccuum lines including the EGR valve for dry rot and the such. The finally you might want to change your fuel filter if it hasn't been done in awhile as well as if posible check your fuel pressure. Disconnect your battery when you are taking the MAF off. I hope this helps and good luck.

Jan 29, 2011 | 2003 Ford Expedition

1 Answer

Volkswagen lt 2.8 cut down on the road, when i restart works


If it sputters to a stop, then I would suspect fuel delivery problems, If it stops abruptly, then likely loss of ignition power (fuse?) or loss of the crank or cam sensor signals. You need to have a code reader attached while driving, that records intermittent faults, to track this one down. It could also be the computer itself!

Aug 08, 2009 | 2005 Volkswagen Microbus

1 Answer

Problems with pressing brakes to stop


U either have a leaking power brake booster or a loss of vacuum to the booster.

Dec 24, 2008 | 2006 Ford F-150

1 Answer

Audi A4, 2.8, 1998


remove the engine strip and rebuild its whats known in the trade as a banger,knackered,thrashed ,had its day.caused by high mileage ,broken piston rings worn valve guides ,valve seats burnt out ,high internal pressure caused by on or all of these things

Jun 05, 2008 | 1998 Audi A4

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...