Question about Cars & Trucks

1 Answer

Where is the position sensor located 5.7 liter chevy sierra k1500

Truck cranks,no start,no spark

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert that has over 500 points.

  • Cars & Trucks Expert
  • 236 Answers

Passenger side of the engine down by the crankshaft behind the harmonic balancer

Posted on Dec 09, 2016


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer


1993 5.7 liters didn't have a crank sensor. They used a pickup coil in the distributor to control spark and injector pulses. (Throttle body injection).

Aug 02, 2013 | 1993 GMC Sierra K1500

2 Answers

Where are the cam & crank position sensors for a 1999 chevy suburbon 5.7?

THE crank sensor is located at bottom of timing cover on front of engine if you look under engine below crank pulley around oil pan timing cover you will see it. the cam sensor is in the distributor.

Dec 22, 2010 | 1999 Chevrolet K1500

1 Answer

1999 chevy pick up 1500 series 4x4 has spark getting fuel new crank position sensor back fires through throttle body wont start

the back firing sounds like to me that the spark plug wires are not in right position on distributor cap, firing on wrong cylinder, did you remove distributor or distributor cap?

Feb 08, 2010 | 1999 Chevrolet K1500

1 Answer

Chevy k1500 5.7 v8 wont start

Sounds like your timing is off when you placed the distributor back in or your spark plug wires are crossed. Start with the simple and check the spark plug wire firing order. 1-8-4-3-6-5-7-2 Cylinder numbers drivers side 1-3-5-7 radiator to firewall. Cylinder numbers passenger side 2-4-6-8 radiator to firewall. Distributor cap #1 is at 5 O'clock and rotates clock wise. Once that is establish to be good then make sure the cylinder 1 is at TDC with the distributor rotor at the #1 position. Good luck and hope it's a crossed firing order.

Jan 11, 2010 | 1994 Chevrolet K1500

2 Answers

97 chevy 4.3 liter no spark no fuel pump running.

4.3 and 2.8 motors have a ceramic module in the distributor. if you have alot of miles on the truck, and there is no spark, that module is usually the culprit. easy to replace with a nut driver and some dielectric grease. mod is located in the distributor when you take the cap off look straight dowm and its right there.
also check eec relay and fuse. that will also cause the prob.

Jul 18, 2009 | 1997 Chevrolet K1500

2 Answers

Engine won't spark' distributor's ohms OK

if you are getting no spark you have 3 different things that could be your problem #1 would be the coil. #2 would be the ignition module located inside the distributor. #3 would be the crank position sensor the last one would throw a code and turn on your service engine soon light.

May 25, 2009 | 1992 GMC Sierra K1500

2 Answers

1998 Chevy silverado K1500 5.7 liter

I would check a few things:
Load test the battery. If its got any age on it at all, this could be the culprit.
Test the starter.
Check for loose connections at the distributor cap. Make sure the rotor in the cap is seated and that the cap is properly seated.
Check for loose connections on the battery, the starter and make sure you have fuel pressure on the injector rails (key on, detent the shrader valve .. you should get fuel).

Sep 27, 2017 | 1996 GMC Sierra

1 Answer

Intermittent long crank times hot or cold service lamp on intermi

Code 43 has different meanings.It has to do with the knock sensor, electronic spark timing failure, left O2 sensor failure, and equate code 42a. Ithink that has to do with ignition switch failure. Good luck.

Mar 05, 2009 | 1993 Chevrolet K1500

1 Answer


try messing with the radiator because it is most likely overheating

Dec 02, 2008 | 1999 Chevrolet Blazer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

77932 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14403 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides