Question about 1999 GMC Jimmy

4 Answers

Passlock how to reset passlock in a 1999 Jimmy

Posted by on

Ad

4 Answers

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 31 Answers

Transmitter programming: with the driver closed, hold down the power unlock button on the door panel. turn the ignition switch to the on position, turn the ignition to the off position turn the ignition to the off position. release the power unlock button on the door panel. the remote control door lock reciever will respond in the following manner in order to indicate that the reciever is in the programming mode. hold down the lock and unlock buttons on the transmitter until the remote control door lock reciever will respond in the following manner: locking the doors, unlocking the doors. this is what I had to do get my new remote to work. good luck.

Posted on Jul 25, 2009

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 186 Answers

Turn key all the way on (not to start) let set for 1 hur cycle key and try it.

Posted on Jul 21, 2009

Ad
  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 31 Answers

Transmitter programming: with the driver closed, hold down the power unlock button on the door panel. turn the ignition switch to the on position, turn the ignition to the off position turn the ignition to the on position. release the power unlock button on the door panel. the remote controlpasslock - 2.gif door lock reciever will respond in the following manner in order to indicate that the reciever is in the programming mode. hold down the lock and unlock buttons on the transmitter until the remote control door lock reciever will respond in the following manner: locking the doors, unlocking the doors. this is what I had to do get my new remote to work. good luck.

Posted on Jul 25, 2009

×

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Expert
  • 59 Answers

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Security light is on my 1999 Chevrolet suburban how to reset it


Passlock on this vehicle shows the key does not have a pellet and no transponder. It's just a mechanical key. It is the tumbler that communicates with passlock sensor. The passlock sensor wiring is noted for problems. Can you check applicable trouble codes?
security-light-1999-chevrolet-suburban-azs333ycsk2k2jdexvu4jvmf-4-0.jpg

Nov 12, 2016 | 1999 Chevrolet Suburban

1 Answer

How do I hot wire a 1999 GMC jimmy


1999 jimmys have a passlock system that is a theft deterrent and cant be "hot-wired" in the normal way. If the cylinder isn't rotated while beinging started correctly - the ecm will disable fuel to the injectors and it will not run

Oct 25, 2015 | GMC Cars & Trucks

1 Answer

How to bypass passlock on 1999 chevy blazer


The most common repair is to replace the ignition lock cylinder due to broken wires inside the steering column. Most common problems related to the Passlock family involve the Passlock sensor. The sensor is part of the ignition lock cylinder on Passlock I and Passlock II systems. ( Where the key goes ), Good-Day!

Aug 27, 2014 | 1999 Chevrolet Blazer

1 Answer

1999 GMC Jimmy Security light


Without the proper testing equipment an knowledge ( factory service info. ) You have no idea what's up . an don't have a chance of fixing this . Checking for DTC'S - diagnostic trouble codes is always the first step . Take's a professional type scan tool to read these codes. Serial data info from module incharge to PCM/ECM ,enable or disable fuel and or starter operation . Sends coded messages Your best bet , take it to a qualified repair shop . That white component is the ignition switch .
The design of the passlock™ system is to prevent the vehicle operation if the proper ignition key is not used in order to start the vehicle. The mechanical key, in normal operation, will turn the passlock™ lock cylinder. The passlock™ sensor will relay the passlock™ data to the body control module (BCM). The BCM will determine the validity of the passlock™ data. The BCM will send a code password to the vehicle/powertrain control module (VCM/PCM). When the VCM/PCM receives the correct code the VCM/PCM allows the fuel injectors to operate normally. The passlock™ system requires the VCM/PCM and the BCM to communicate the various functions in order to operate. These functions transmit over the class 2 serial data line CKT 1807. For an explanation of the class 2 serial data operation refer to Data Link Communications Circuit Description in Wiring Systems

Oct 07, 2017 | 1999 GMC Jimmy

2 Answers

WHERE IS THE FUSE OR RELAY FOR THE FACTORY ALARM 99GMCJIMMY


check at battery for voltage with truck off,then check battery condition.it (the battery) could be weak.

Aug 16, 2009 | 1999 GMC Jimmy

1 Answer

Passlock gmc jimmy


try this, turn key on but do not try to start, walk away for 30 mins, turn key off for 1 min, then try to start

Aug 04, 2009 | 2000 GMC Jimmy

Not finding what you are looking for?
1999 GMC Jimmy Logo

Related Topics:

1,018 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...