Question about Cars & Trucks

1 Answer

I HAD THEMORSTAT REPLACED AND TOP HOSE BUT IT KEEPS COLLASPING WHAT DO I NEED TO DO

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 75,807 Answers

You are low on coolant that is the most common reason that hose will do that. You likely need to bleed the air out of the cooling system. I also suggest you replace the radiator cap as it may cause this as well, but that is very rare.

Follow the link to asssit you to bleed it of air. How to Burp your car cooling system

Posted on Dec 09, 2016

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Thermorstat replace


follow upper radiator hose to top of engine , remove 2 bolts, thermosstat is underneath this , remove old stat, clean gasket off, replace thermostat & gasket, note position of old stat, place new stat in same postion, & new gasket, reinstall bolts tighten, done

Feb 02, 2013 | 2003 Chevrolet Impala

1 Answer

Honda 2003 themorstat


remove lower splash shield, follow lower coolant hose to engine thermostat housing.

Nov 09, 2012 | 2003 Honda CR-V

1 Answer

2002 pontiac montana overheats


i would 1st check the thermostat, most overheating problems result from the thermostat sticking closed, and not allowing the coolant to circulate, while you are doing this, check the upper and lower radiator and heater hoses, to make sure that they are not collasping, also check the coolant temperature switch. this switch is normally located on the top of the intake manifold, most of the time, not too far from where the top radiator hose is connected. hope that this information has helped you.

Mar 30, 2011 | 2002 Pontiac Montana

1 Answer

Hi i have a 1988 cadilliac seville changed the therstat on it it reads some times 150 to 170 degree but a lot of time it only reads only 120 degree the main top hose is only warm and it idles realy high...


it should go to 195 degrees if new
either the coolant galeries areplugged up somewhere
it can be from the heater core
radiator
engine block or heads
a collasped hose will do that also keeping the temperature down
ever a bad seal on the overflow tank or radiatop too

Nov 21, 2010 | 1988 Cadillac Seville

1 Answer

Front brakes keep seizing up on 96 nissan pick up ..replaced calipers..pads..rotars..master cylinder..still locking up


The rubber brake hose can be clogged or collasped causing this problem Bleed the system of all brake fluid on this and try before replacing the hoses

Jul 17, 2010 | 1996 Nissan Pickup

1 Answer

Where is themorstat?


the thermostat is located in the housing where the top radiator hose goes onto the engine.....hope this helps .....cheers

Jul 13, 2010 | 2003 Chevrolet Impala

1 Answer

My front brakes lockin up on my 92 eagle talon


The cause is most likely caused by a defective brake hose. The flexible line that runs to the caliper has collasped inside, causing the pressure to remain on the caliper. These hoses have a very small passage and easily collapse over time due to wear. Just a thought.

Jul 08, 2010 | 1992 Eagle Talon

2 Answers

Coolant doesn't appear to be moving through engine


Check for a collasped hose
A frozen shut thermostat
a plugged up radiator or heater core

May 11, 2010 | 1997 Ford Contour

1 Answer

90 lincoln was running hot 3 yrs ago,and no heat just replaced head gasket,heads pass pressure test,no cracks in heads, head gasket was bad,still no heat,heater hoses hot, pressure test cooling system...


Have you even considered the heater core? Have the heater core checked/replaced. As for the top hose collapsing...that is not good. Have the entire system checked out by a qualified mechanic.

Feb 15, 2010 | 1997 Lincoln Continental

1 Answer

Vacuum hoses make sucking sound


The hoses are probaly collasped....it's like tring to **** a real thick milkshake through a skinny straw..it collaspes due to the pressure, and being weak..All you have to do is find which one or ones it is, and replace it...

Dec 04, 2009 | 1992 Ford Explorer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...