Question about Mazda Cars & Trucks

1 Answer

MY MAZDA STILL STARTS AND IDLES BUT CUTS OUT AFTER 2000 RPMS ANY SUGGESTIONS WHAT THIS CAN BE I ALREADY REPLACED THE PLUGS CORDS AND DIST CAP , REPLACED FUEL FILTER TESTED PRESSURE ON FUEL PUMP

CAN IT BE THE ECU THAT IS FAULTY

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Night Owl:

    An expert who has answered 10 or more questions between 12 midnight and 6am on the same day.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 35 Answers

Change your fuel filter

Posted on Dec 10, 2016

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2000 gmc jimmy 4x4 p0300. Replaced cap, rotor, wires, plugs, map sensor, checked icm. Nothing has helped


Just a thought,pull the dist.cap and make sure the rotor has
no side to side play ,thinking maybe a bad upper bushing in
the dist.Also,if the EGR valve has carbon and soot built up
on the piston it will make it idle really poor ,but run ok.
Might pull the EGR and clean it with intake cleaner.
Hope this helps.

Apr 12, 2013 | 2000 GMC Jimmy

1 Answer

2000 chevrolet silverado 1500 4.3l v6 misses at 2000 rpm and now wont start


It sounds like u have a cam correlation problem... Take ur cap off mark where ur rotor is pointing on the dist. Mark the firewall where the dist plug is pointing take the 10mm bolt out n look @ the dist gear and see how bad it's worn!! When u take the cap off some times they're so bad when u move the rotor u can tell the excessive play hope this helps!!!!

Dec 18, 2011 | 2000 Chevrolet Silverado 1500

1 Answer

MY 1984 GS CARB RUNS GOOD, STARTS GOOD WON'T IDLE BELOW 1500 RPMS, CLEANED CARB, ALL JETS CLEANED, JUST GOT IT AND WONDER IF SOMETHING NOT SET OR CONTROL HOSES ON WRONG, I HAD A 1984 NEW AND A 1985 YEARS...


Replace your fuel filter first, cheap and easy to rule out, probably needs it anyways. Could also be a massive vacuum leak. On that year's carb there are 2 adjustments... Here's a page on idle tuning: http://sterlingmetalworks.com/tuning_the_nikki.htm

May 05, 2011 | 1984 Mazda RX-7

1 Answer

Multiple missfires on 2000 blazer just off idle. seems better with the map sensor disconnected.4.3


first off, just take distributor cap off and check the cap for corrosion and pitting. turn the dist. shaft by hand. if it turns a lot then the gear on bottom of dist, shaft is worn. you can either replace dist. or replace gear on shaft. check all wires and plugs. hard to say, but i would start at distributor to see if it is ok.

Apr 20, 2011 | 2000 Chevrolet Blazer

2 Answers

Misfires 96 gmc sierra 5.0


if the check engine light starts flashing its probably setting a code may have an injector problem

Aug 05, 2009 | 1996 GMC Sierra

2 Answers

RPM's will not stay at a steady pace


have you thought about the idle air control (iac) or T.p.s sensor try unpluging the Iac see what happens. Just a thought also listen for a vacum leak

Jun 27, 2009 | 1996 Mazda Protege

1 Answer

1994 Geo Tracker 4x4 Automatic


it is probably out of water as mine did that and the radiator was dry. due to a bad water pump.

Nov 02, 2008 | 1992 Geo Tracker

4 Answers

Mazda 626 engine cut off when excel over 3000 rmp


my 1988 mazda 626 starts okay then dies everytime it idles down to normal idle speed. i replaced the throttle control sensor and the mass air sensor. i replaced the rotor in the distributor but is still dies. if you throttle up to about 1500 rpm it keeps running. any ideas???

Aug 04, 2008 | 1994 Mazda 626

2 Answers

1994 Nissan Hardbody limited rpms when warm


HAVE YOUR EXHAUST CONVERTER CHECKED! IF IT'S BAD AND YOU HAVE IT REPLACED, DON'T LET THE ONE THAT REPLACE'S IT TAKE YOUR OLD ONE!!!!! IT'S WORTH ABOUT $250.00

May 19, 2008 | 1994 Nissan Pickup

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8729 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...